This patch adds support for the Ka-Ro electronics GmbH TX6 modules. There are four distinct module types. Two equipped with an i.MX6Q processor, two with i.MX6DL. Each of these has either an LVDS display interface or a parallel LCD interface.
Signed-off-by: Lothar Waßmann <[email protected]> --- arch/arm/boot/dts/Makefile | 4 + arch/arm/boot/dts/imx6dl-tx6u-801x.dts | 350 +++++++++++++++++++++++++ arch/arm/boot/dts/imx6dl-tx6u-811x.dts | 242 ++++++++++++++++++ arch/arm/boot/dts/imx6q-tx6q-101x.dts | 350 +++++++++++++++++++++++++ arch/arm/boot/dts/imx6q-tx6q-111x.dts | 246 ++++++++++++++++++ arch/arm/boot/dts/imx6qdl-tx6.dtsi | 434 ++++++++++++++++++++++++++++++++ 6 files changed, 1626 insertions(+), 0 deletions(-) create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-801x.dts create mode 100644 arch/arm/boot/dts/imx6dl-tx6u-811x.dts create mode 100644 arch/arm/boot/dts/imx6q-tx6q-101x.dts create mode 100644 arch/arm/boot/dts/imx6q-tx6q-111x.dts create mode 100644 arch/arm/boot/dts/imx6qdl-tx6.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 535c98f..40175a9 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -152,6 +152,8 @@ dtb-$(CONFIG_ARCH_MXC) += \ imx6dl-gw54xx.dtb \ imx6dl-sabreauto.dtb \ imx6dl-sabresd.dtb \ + imx6dl-tx6u-801x.dtb \ + imx6dl-tx6u-811x.dtb \ imx6dl-wandboard.dtb \ imx6q-arm2.dtb \ imx6q-cm-fx6.dtb \ @@ -166,6 +168,8 @@ dtb-$(CONFIG_ARCH_MXC) += \ imx6q-sabrelite.dtb \ imx6q-sabresd.dtb \ imx6q-sbc6x.dtb \ + imx6q-tx6q-101x.dtb \ + imx6q-tx6q-111x.dtb \ imx6q-udoo.dtb \ imx6q-wandboard.dtb \ imx6sl-evk.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-tx6u-801x.dts b/arch/arm/boot/dts/imx6dl-tx6u-801x.dts new file mode 100644 index 0000000..453a05b --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-tx6u-801x.dts @@ -0,0 +1,350 @@ +/* + * Copyright 2013 Lothar Waßmann <[email protected]> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-tx6.dtsi" + +/ { + model = "Ka-Ro electronics TX6DL Module"; + compatible = "fsl,imx6dl-tx6dl", "fsl,imx6dl"; + + aliases { + display = &display; + lcdif_23bit_pins_a = &pinctrl_disp0_1; + lcdif_24bit_pins_a = &pinctrl_disp0_2; + }; + + backlight@0 { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 500000>; + power-supply = <®_3v3>; + /* + * a poor man's way to create an inverse 1:1 relationship + * between the PWM value and the actual duty cycle + */ + brightness-levels = <100 + 99 98 97 96 95 94 93 92 91 90 + 89 88 87 86 85 84 83 82 81 80 + 79 78 77 76 75 74 73 72 71 70 + 69 68 67 66 65 64 63 62 61 60 + 59 58 57 56 55 54 53 52 51 50 + 49 48 47 46 45 44 43 42 41 40 + 39 38 37 36 35 34 33 32 31 30 + 29 28 27 26 25 24 23 22 21 20 + 19 18 17 16 15 14 13 12 11 10 + 9 8 7 6 5 4 3 2 1 0>; + default-brightness-level = <50>; + }; + + display: display@di0 { + compatible = "fsl,imx-parallel-display"; + crtcs = <&ipu1 0>; + interface-pix-fmt = "rgb24"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_disp0_1>; + status = "okay"; + + display-timings { + timing@0 { + panel-name = "VGA"; + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <48>; + hsync-len = <96>; + hfront-porch = <16>; + vback-porch = <31>; + vsync-len = <2>; + vfront-porch = <12>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + timing@1 { + panel-name = "ETV570"; + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <114>; + hsync-len = <30>; + hfront-porch = <16>; + vback-porch = <32>; + vsync-len = <3>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + timing@2 { + panel-name = "ET0350"; + clock-frequency = <6413760>; + hactive = <320>; + vactive = <240>; + hback-porch = <34>; + hsync-len = <34>; + hfront-porch = <20>; + vback-porch = <15>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + timing@3 { + panel-name = "ET0430"; + clock-frequency = <9009000>; + hactive = <480>; + vactive = <272>; + hback-porch = <2>; + hsync-len = <41>; + hfront-porch = <2>; + vback-porch = <2>; + vsync-len = <10>; + vfront-porch = <2>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing@4 { + panel-name = "ET0500"; + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + timing@5 { + panel-name = "ET0700"; /* same as ET0500 */ + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + timing@6 { + panel-name = "ETQ570"; + clock-frequency = <6596040>; + hactive = <320>; + vactive = <240>; + hback-porch = <38>; + hsync-len = <30>; + hfront-porch = <30>; + vback-porch = <16>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; + + regulators { + reg_lcd_pwr: regulator@6 { + compatible = "regulator-fixed"; + regulator-name = "LCD POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + + reg_lcd_reset: regulator@7 { + compatible = "regulator-fixed"; + regulator-name = "LCD RESET"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>; + startup-delay-us = <300000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + }; + }; +}; + +&i2c3 { + touchscreen: tsc2007@48 { + compatible = "ti,tsc2007"; + reg = <0x48>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc2007>; + interrupt-parent = <&gpio3>; + interrupts = <26 0>; + gpios = <&gpio3 26 GPIO_ACTIVE_LOW>; + ti,x-plate-ohms = <660>; + linux,wakeup; + }; + + polytouch: edt-ft5x06@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_edt_ft5x06>; + interrupt-parent = <&gpio6>; + interrupts = <15 0>; + reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; + wake-gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; + }; +}; + +&iomuxc { + display { + pinctrl_disp0_1: disp0grp-1 { + fsl,pins = < + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10 + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 + /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */ + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10 + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10 + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10 + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10 + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10 + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10 + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10 + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10 + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10 + >; + }; + + pinctrl_disp0_2: disp0grp-2 { + fsl,pins = < + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10 + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10 + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10 + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10 + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10 + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10 + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10 + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10 + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10 + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10 + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10 + >; + }; + }; + + kpp { + pinctrl_kpp: kppgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_9__KEY_COL6 0x1b0b1 + MX6QDL_PAD_GPIO_4__KEY_COL7 0x1b0b1 + MX6QDL_PAD_KEY_COL2__KEY_COL2 0x1b0b1 + MX6QDL_PAD_KEY_COL3__KEY_COL3 0x1b0b1 + + MX6QDL_PAD_GPIO_2__KEY_ROW6 0x1b0b1 + MX6QDL_PAD_GPIO_5__KEY_ROW7 0x1b0b1 + MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x1b0b1 + MX6QDL_PAD_KEY_ROW3__KEY_ROW3 0x1b0b1 + >; + }; + }; + + touchpanel { + pinctrl_tsc2007: tsc2007grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x1b0b0 /* Interrupt */ + >; + }; + + pinctrl_edt_ft5x06: edt-ft5x06grp { + fsl,pins = < + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 /* Interrupt */ + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b0b0 /* Reset */ + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0 /* Wake */ + >; + }; + }; +}; + +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp>; + status = "okay"; + + /* sample keymap */ + /* row/col 0,1 are mapped to KPP row/col 6,7 */ + linux,keymap = < + 0x06060074 /* row 6, col 6, KEY_POWER */ + 0x06070052 /* row 6, col 7, KEY_KP0 */ + 0x0602004f /* row 6, col 2, KEY_KP1 */ + 0x06030050 /* row 6, col 3, KEY_KP2 */ + 0x07060051 /* row 7, col 6, KEY_KP3 */ + 0x0707004b /* row 7, col 7, KEY_KP4 */ + 0x0702004c /* row 7, col 2, KEY_KP5 */ + 0x0703004d /* row 7, col 3, KEY_KP6 */ + 0x02060047 /* row 2, col 6, KEY_KP7 */ + 0x02070048 /* row 2, col 7, KEY_KP8 */ + 0x02020049 /* row 2, col 2, KEY_KP9 */ + >; +}; diff --git a/arch/arm/boot/dts/imx6dl-tx6u-811x.dts b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts new file mode 100644 index 0000000..1c4b24e --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-tx6u-811x.dts @@ -0,0 +1,242 @@ +/* + * Copyright 2013 Lothar Waßmann <[email protected]> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-tx6.dtsi" + +/ { + model = "Ka-Ro electronics TX6DL (LVDS) Module"; + compatible = "fsl,imx6dl-tx6dl", "fsl,imx6dl"; + + aliases { + display = &lvds0; + lvds0 = &lvds0; + lvds1 = &lvds1; + }; + + backlight@0 { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 500000>; + power-supply = <®_3v3>; + brightness-levels = < + 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100 + >; + default-brightness-level = <50>; + }; + + backlight1: pwm-backlight@1 { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 500000>; + power-supply = <®_3v3>; + brightness-levels = < + 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100 + >; + default-brightness-level = <50>; + }; + + + regulators { + reg_lcd_pwr: regulator@6 { + compatible = "regulator-fixed"; + regulator-name = "LVDS0 POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + + reg_lcd_reset: regulator@7 { + compatible = "regulator-fixed"; + regulator-name = "LVDS1 POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + }; +}; + +&i2c2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + + touchscreen2: eeti@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eeti_2>; + interrupt-parent = <&gpio3>; + interrupts = <23 0>; + wakeup-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + linux,wakeup; + }; +}; + +&i2c3 { + touchscreen1: eeti@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eeti_1>; + interrupt-parent = <&gpio3>; + interrupts = <22 0>; + wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; + linux,wakeup; + }; +}; + +&iomuxc { + i2c { + pinctrl_i2c2: i2c2-grp1 { + fsl,pins = <MX6QDL_I2C2_PINGRP2>; + }; + }; + + kpp { + pinctrl_kpp: kppgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_9__KEY_COL6 0x1b0b1 + MX6QDL_PAD_GPIO_4__KEY_COL7 0x1b0b1 + MX6QDL_PAD_KEY_COL2__KEY_COL2 0x1b0b1 + + MX6QDL_PAD_GPIO_2__KEY_ROW6 0x1b0b1 + MX6QDL_PAD_GPIO_5__KEY_ROW7 0x1b0b1 + MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x1b0b1 + >; + }; + }; + + pwm { + pinctrl_pwm1: pwm1grp { + fsl,pins = <MX6QDL_PAD_GPIO_9__PWM1_OUT 0x80000000>; + }; + }; + + touchpanel { + pinctrl_eeti_1: eetigrp-1 { + fsl,pins = < + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0xe0 /* Interrupt */ + >; + }; + + pinctrl_eeti_2: eetigrp-2 { + fsl,pins = < + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0xe0 /* Interrupt */ + >; + }; + }; +}; + +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp>; + status = "okay"; + + /* sample keymap */ + /* row/col 0,1 are mapped to KPP row/col 6,7 + * row/col 3 are used for I2C2 (second touch controller on hsd100pxn1) + */ + linux,keymap = < + 0x06060074 /* row 6, col 6, KEY_POWER */ + 0x06070052 /* row 6, col 7, KEY_KP0 */ + 0x0602004f /* row 6, col 2, KEY_KP1 */ + 0x07060050 /* row 7, col 6, KEY_KP2 */ + 0x07070051 /* row 7, col 7, KEY_KP3 */ + 0x0702004b /* row 7, col 2, KEY_KP4 */ + 0x0206004c /* row 2, col 6, KEY_KP5 */ + 0x0207004d /* row 2, col 7, KEY_KP6 */ + 0x02020047 /* row 2, col 2, KEY_KP7 */ + >; +}; + +&ldb { + status = "okay"; +// fsl,dual-channel; + + lvds0: lvds-channel@0 { + fsl,data-mapping = "jeida"; + fsl,data-width = <24>; + status = "okay"; + + display-timings { + native-mode = <&lvds_timing0>; + lvds_timing0: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hsync-len = <60>; + hfront-porch = <40>; + vback-porch = <21>; + vsync-len = <10>; + vfront-porch = <7>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; + + lvds1: lvds-channel@1 { + fsl,data-mapping = "jeida"; + fsl,data-width = <24>; + status = "okay"; + + display-timings { + native-mode = <&lvds_timing1>; + lvds_timing1: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hsync-len = <60>; + hfront-porch = <40>; + vback-porch = <21>; + vsync-len = <10>; + vfront-porch = <7>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; +}; diff --git a/arch/arm/boot/dts/imx6q-tx6q-101x.dts b/arch/arm/boot/dts/imx6q-tx6q-101x.dts new file mode 100644 index 0000000..066bbee --- /dev/null +++ b/arch/arm/boot/dts/imx6q-tx6q-101x.dts @@ -0,0 +1,350 @@ +/* + * Copyright 2013 Lothar Waßmann <[email protected]> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include "imx6qdl-tx6.dtsi" + +/ { + model = "Ka-Ro electronics TX6Q Module"; + compatible = "fsl,imx6q-tx6q", "fsl,imx6q"; + + aliases { + display = &display; + lcdif_23bit_pins_a = &pinctrl_disp0_1; + lcdif_24bit_pins_a = &pinctrl_disp0_2; + }; + + backlight@0 { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 500000>; + power-supply = <®_3v3>; + /* + * a poor man's way to create an inverse 1:1 relationship + * between the PWM value and the actual duty cycle + */ + brightness-levels = <100 + 99 98 97 96 95 94 93 92 91 90 + 89 88 87 86 85 84 83 82 81 80 + 79 78 77 76 75 74 73 72 71 70 + 69 68 67 66 65 64 63 62 61 60 + 59 58 57 56 55 54 53 52 51 50 + 49 48 47 46 45 44 43 42 41 40 + 39 38 37 36 35 34 33 32 31 30 + 29 28 27 26 25 24 23 22 21 20 + 19 18 17 16 15 14 13 12 11 10 + 9 8 7 6 5 4 3 2 1 0>; + default-brightness-level = <50>; + }; + + display: display@di0 { + compatible = "fsl,imx-parallel-display"; + crtcs = <&ipu1 0>; + interface-pix-fmt = "rgb24"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_disp0_1>; + status = "okay"; + + display-timings { + timing@0 { + panel-name = "VGA"; + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <48>; + hsync-len = <96>; + hfront-porch = <16>; + vback-porch = <31>; + vsync-len = <2>; + vfront-porch = <12>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + timing@1 { + panel-name = "ETV570"; + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <114>; + hsync-len = <30>; + hfront-porch = <16>; + vback-porch = <32>; + vsync-len = <3>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + timing@2 { + panel-name = "ET0350"; + clock-frequency = <6413760>; + hactive = <320>; + vactive = <240>; + hback-porch = <34>; + hsync-len = <34>; + hfront-porch = <20>; + vback-porch = <15>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + timing@3 { + panel-name = "ET0430"; + clock-frequency = <9009000>; + hactive = <480>; + vactive = <272>; + hback-porch = <2>; + hsync-len = <41>; + hfront-porch = <2>; + vback-porch = <2>; + vsync-len = <10>; + vfront-porch = <2>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + timing@4 { + panel-name = "ET0500"; + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + timing@5 { + panel-name = "ET0700"; /* same as ET0500 */ + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + timing@6 { + panel-name = "ETQ570"; + clock-frequency = <6596040>; + hactive = <320>; + vactive = <240>; + hback-porch = <38>; + hsync-len = <30>; + hfront-porch = <30>; + vback-porch = <16>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; + + regulators { + reg_lcd_pwr: regulator@6 { + compatible = "regulator-fixed"; + regulator-name = "LCD POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + + reg_lcd_reset: regulator@7 { + compatible = "regulator-fixed"; + regulator-name = "LCD RESET"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>; + startup-delay-us = <300000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + }; + }; +}; + +&i2c3 { + touchscreen: tsc2007@48 { + compatible = "ti,tsc2007"; + reg = <0x48>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc2007>; + interrupt-parent = <&gpio3>; + interrupts = <26 0>; + gpios = <&gpio3 26 GPIO_ACTIVE_LOW>; + ti,x-plate-ohms = <660>; + linux,wakeup; + }; + + polytouch: edt-ft5x06@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_edt_ft5x06>; + interrupt-parent = <&gpio6>; + interrupts = <15 0>; + reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; + wake-gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; + }; +}; + +&iomuxc { + display { + pinctrl_disp0_1: disp0grp-1 { + fsl,pins = < + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10 + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 + /* PAD DISP0_DAT0 is used for the Flexcan transceiver control */ + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10 + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10 + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10 + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10 + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10 + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10 + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10 + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10 + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10 + >; + }; + + pinctrl_disp0_2: disp0grp-2 { + fsl,pins = < + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10 + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10 + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10 + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10 + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10 + MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10 + MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10 + MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10 + MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10 + MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10 + MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10 + >; + }; + }; + + kpp { + pinctrl_kpp: kppgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_9__KEY_COL6 0x1b0b1 + MX6QDL_PAD_GPIO_4__KEY_COL7 0x1b0b1 + MX6QDL_PAD_KEY_COL2__KEY_COL2 0x1b0b1 + MX6QDL_PAD_KEY_COL3__KEY_COL3 0x1b0b1 + + MX6QDL_PAD_GPIO_2__KEY_ROW6 0x1b0b1 + MX6QDL_PAD_GPIO_5__KEY_ROW7 0x1b0b1 + MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x1b0b1 + MX6QDL_PAD_KEY_ROW3__KEY_ROW3 0x1b0b1 + >; + }; + }; + + touchpanel { + pinctrl_tsc2007: tsc2007grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x1b0b0 /* Interrupt */ + >; + }; + + pinctrl_edt_ft5x06: edt-ft5x06grp { + fsl,pins = < + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 /* Interrupt */ + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b0b0 /* Reset */ + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0 /* Wake */ + >; + }; + }; +}; + +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp>; + status = "okay"; + + /* sample keymap */ + /* row/col 0,1 are mapped to KPP row/col 6,7 */ + linux,keymap = < + 0x06060074 /* row 6, col 6, KEY_POWER */ + 0x06070052 /* row 6, col 7, KEY_KP0 */ + 0x0602004f /* row 6, col 2, KEY_KP1 */ + 0x06030050 /* row 6, col 3, KEY_KP2 */ + 0x07060051 /* row 7, col 6, KEY_KP3 */ + 0x0707004b /* row 7, col 7, KEY_KP4 */ + 0x0702004c /* row 7, col 2, KEY_KP5 */ + 0x0703004d /* row 7, col 3, KEY_KP6 */ + 0x02060047 /* row 2, col 6, KEY_KP7 */ + 0x02070048 /* row 2, col 7, KEY_KP8 */ + 0x02020049 /* row 2, col 2, KEY_KP9 */ + >; +}; diff --git a/arch/arm/boot/dts/imx6q-tx6q-111x.dts b/arch/arm/boot/dts/imx6q-tx6q-111x.dts new file mode 100644 index 0000000..102666a --- /dev/null +++ b/arch/arm/boot/dts/imx6q-tx6q-111x.dts @@ -0,0 +1,246 @@ +/* + * Copyright 2013 Lothar Waßmann <[email protected]> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include "imx6qdl-tx6.dtsi" + +/ { + model = "Ka-Ro electronics TX6Q (LVDS) Module"; + compatible = "fsl,imx6q-tx6q", "fsl,imx6q"; + + aliases { + display = &lvds0; + lvds0 = &lvds0; + lvds1 = &lvds1; + }; + + backlight@0 { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 500000>; + power-supply = <®_3v3>; + brightness-levels = < + 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100 + >; + default-brightness-level = <50>; + }; + + backlight1: pwm-backlight@1 { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 500000>; + power-supply = <®_3v3>; + brightness-levels = < + 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100 + >; + default-brightness-level = <50>; + }; + + + regulators { + reg_lcd_pwr: regulator@6 { + compatible = "regulator-fixed"; + regulator-name = "LVDS0 POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + + reg_lcd_reset: regulator@7 { + compatible = "regulator-fixed"; + regulator-name = "LVDS1 POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + }; +}; + +&i2c2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + + touchscreen2: eeti@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eeti_2>; + interrupt-parent = <&gpio3>; + interrupts = <23 0>; + wakeup-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + linux,wakeup; + }; +}; + +&i2c3 { + touchscreen1: eeti@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eeti_1>; + interrupt-parent = <&gpio3>; + interrupts = <22 0>; + wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; + linux,wakeup; + }; +}; + +&iomuxc { + i2c { + pinctrl_i2c2: i2c2-grp1 { + fsl,pins = <MX6QDL_I2C2_PINGRP2>; + }; + }; + + kpp { + pinctrl_kpp: kppgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_9__KEY_COL6 0x1b0b1 + MX6QDL_PAD_GPIO_4__KEY_COL7 0x1b0b1 + MX6QDL_PAD_KEY_COL2__KEY_COL2 0x1b0b1 + + MX6QDL_PAD_GPIO_2__KEY_ROW6 0x1b0b1 + MX6QDL_PAD_GPIO_5__KEY_ROW7 0x1b0b1 + MX6QDL_PAD_KEY_ROW2__KEY_ROW2 0x1b0b1 + >; + }; + }; + + pwm { + pinctrl_pwm1: pwm1grp { + fsl,pins = <MX6QDL_PAD_GPIO_9__PWM1_OUT 0x80000000>; + }; + }; + + touchpanel { + pinctrl_eeti_1: eetigrp-1 { + fsl,pins = < + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0xe0 /* Interrupt */ + >; + }; + + pinctrl_eeti_2: eetigrp-2 { + fsl,pins = < + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0xe0 /* Interrupt */ + >; + }; + }; +}; + +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp>; + status = "okay"; + + /* sample keymap */ + /* row/col 0,1 are mapped to KPP row/col 6,7 + * row/col 3 are used for I2C2 (second touch controller on hsd100pxn1) + */ + linux,keymap = < + 0x06060074 /* row 6, col 6, KEY_POWER */ + 0x06070052 /* row 6, col 7, KEY_KP0 */ + 0x0602004f /* row 6, col 2, KEY_KP1 */ + 0x07060050 /* row 7, col 6, KEY_KP2 */ + 0x07070051 /* row 7, col 7, KEY_KP3 */ + 0x0702004b /* row 7, col 2, KEY_KP4 */ + 0x0206004c /* row 2, col 6, KEY_KP5 */ + 0x0207004d /* row 2, col 7, KEY_KP6 */ + 0x02020047 /* row 2, col 2, KEY_KP7 */ + >; +}; + +&ldb { + status = "okay"; +// fsl,dual-channel; + + lvds0: lvds-channel@0 { + fsl,data-mapping = "jeida"; + fsl,data-width = <24>; + status = "okay"; + + display-timings { + native-mode = <&lvds_timing0>; + lvds_timing0: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hsync-len = <60>; + hfront-porch = <40>; + vback-porch = <21>; + vsync-len = <10>; + vfront-porch = <7>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; + + lvds1: lvds-channel@1 { + fsl,data-mapping = "jeida"; + fsl,data-width = <24>; + status = "okay"; + + display-timings { + native-mode = <&lvds_timing1>; + lvds_timing1: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hsync-len = <60>; + hfront-porch = <40>; + vback-porch = <21>; + vsync-len = <10>; + vfront-porch = <7>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi new file mode 100644 index 0000000..af315db --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi @@ -0,0 +1,434 @@ +/* + * Copyright 2013 Lothar Waßmann <[email protected]> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include <dt-bindings/gpio/gpio.h> + +/ { + aliases { + can0 = &can1; + can1 = &can2; + ethernet0 = &fec; + reg_can_xcvr = ®_can_xcvr; + stk5led = &user_led; + usbotg = &usbotg; + }; + + chosen { + }; + + memory { + reg = <0 0>; /* will be filled by U-Boot */ + }; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + mclk: codec_clock { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + power { + label = "Power Button"; + gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>; + linux,code = <116>; /* KEY_POWER */ + gpio-key,wakeup; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led>; + + user_led: user { + label = "Heartbeat"; + gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + regulators { + compatible = "simple-bus"; + + reg_3v3_etn: regulator@0 { + compatible = "regulator-fixed"; + regulator-name = "3V3_ETN"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_2v5: regulator@1 { + compatible = "regulator-fixed"; + regulator-name = "2V5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + + reg_3v3: regulator@2 { + compatible = "regulator-fixed"; + regulator-name = "3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_can_xcvr: regulator@3 { + compatible = "regulator-fixed"; + regulator-name = "CAN XCVR"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>; + enable-active-low; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan_xcvr>; + }; + + reg_usbh1_vbus: regulator@4 { + compatible = "regulator-fixed"; + regulator-name = "usbh1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1_vbus>; + gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usbotg_vbus: regulator@5 { + compatible = "regulator-fixed"; + regulator-name = "usbotg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg_vbus>; + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + }; + + sound { + compatible = "fsl,imx6qdl-tx6qdl-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "sgtl5000-audio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + ssi-controller = <&ssi1>; + audio-codec = <&sgtl5000>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <5>; + }; +}; + +&audmux { + status = "okay"; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_can_xcvr>; + + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + xceiver-supply = <®_can_xcvr>; + + status = "okay"; +}; + +&ecspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + fsl,spi-num-chipselects = <2>; + cs-gpios = < + &gpio2 30 GPIO_ACTIVE_HIGH + &gpio3 19 GPIO_ACTIVE_HIGH + >; + status = "okay"; + + spidev@0 { + compatible = "spidev"; + reg = <0>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rmii"; + phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_HIGH>; + phy-supply = <®_3v3_etn>; + status = "okay"; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + nand-on-flash-bbt; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clock-frequency = <400000>; + status = "okay"; + + ds1339: rtc@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clock-frequency = <400000>; + status = "okay"; + + sgtl5000: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_2v5>; + VDDIO-supply = <®_3v3>; + clocks = <&mclk>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + audmux { + pinctrl_audmux: audmuxgrp { + fsl,pins = <MX6QDL_AUDMUX_PINGRP5>; + }; + }; + + enet { + pinctrl_enet: enetgrp { + fsl,pins = <MX6QDL_ENET_PINGRP4>; + }; + }; + + flexcan { + pinctrl_flexcan1: flexcan1grp { + }; + + pinctrl_flexcan2: flexcan2grp { + }; + + pinctrl_flexcan_xcvr: flexcan-xcvrgrp { + fsl,pins = <MX6QDL_PAD_DISP0_DAT0__GPIO4_IO21 0x1b0b0>; /* Flexcan XCVR enable */ + }; + }; + + hog { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */ + MX6QDL_PAD_SD3_DAT2__GPIO7_IO06 0x1b0b1 /* ETN PHY RESET */ + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1 /* ETN PHY POWER */ + MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1b0b1 /* ETN PHY INT + MX6QDL_PAD_SD3_CMD__GPIO7_IO02 0x1b0b0 /* SD1 CD */ + MX6QDL_PAD_SD3_CLK__GPIO7_IO03 0x1b0b0 /* SD2 CD */ + MX6QDL_PAD_EIM_EB3__GPIO2_IO31 0x1b0b1 /* LCD Power Enable */ + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x1b0b1 /* LCD Reset */ + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b1 /* PWR BTN */ + >; + }; + }; + + i2c { + pinctrl_i2c1: i2c1grp { + fsl,pins = <MX6QDL_I2C1_PINGRP1>; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = <MX6QDL_I2C3_PINGRP2>; + }; + }; + + led { + pinctrl_led: ledgrp { + fsl,pins = < + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b1 /* LED */ + >; + }; + }; + + nand { + pinctrl_gpmi_nand: gpmi-nand { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + >; + }; + }; + + pwm { + pinctrl_pwm2: pwm2grp { + fsl,pins = <MX6QDL_PAD_GPIO_1__PWM2_OUT 0xb0b1>; + }; + }; + + ecspi { + pinctrl_ecspi1: ecspi1grp { + fsl,pins = <MX6QDL_ECSPI1_PINGRP1 + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b1 + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b0b1 + MX6QDL_PAD_GPIO_19__ECSPI1_RDY 0x1b0b1 + >; + }; + }; + + uart { + pinctrl_uart1: uart1grp { + fsl,pins = <MX6QDL_UART1_PINGRP2 + MX6QDL_PAD_SD3_DAT0__UART1_CTS_B 0x1b0b1 + MX6QDL_PAD_SD3_DAT1__UART1_RTS_B 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = <MX6QDL_UART2_PINGRP3 + MX6QDL_PAD_SD4_DAT6__UART2_CTS_B 0x1b0b1 + MX6QDL_PAD_SD4_DAT5__UART2_RTS_B 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = <MX6QDL_UART3_PINGRP3 + MX6QDL_PAD_SD3_DAT3__UART3_CTS_B 0x1b0b1 + MX6QDL_PAD_SD3_RST__UART3_RTS_B 0x1b0b1 + >; + }; + }; + + usbh1 { + pinctrl_usbh1_vbus: usbh1-vbusgrp { + fsl,pins = < + MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0 /* USBH1_VBUSEN */ + >; + }; + }; + + usbotg { + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x17059 + >; + }; + + pinctrl_usbotg_vbus: usbotg-vbusgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_7__GPIO1_IO07 0x1b0b0 /* USBOTG_VBUSEN */ + >; + }; + }; + + usdhc { + pinctrl_usdhc1: ussdhc1grp { + fsl,pins = <MX6QDL_USDHC1_PINGRP_D4_200MHZ>; + }; + + pinctrl_usdhc2: ussdhc2grp { + fsl,pins = <MX6QDL_USDHC2_PINGRP_D4_200MHZ>; + }; + }; +}; + +&pwm2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; + status = "okay"; +}; + +&ssi1 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usbh1_vbus>; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usbotg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + dr_mode = "peripheral"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + cd-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; -- 1.7.2.5 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
