Hi Tien Hock,
On 1/22/14 12:09 PM, Gerhard Sittig wrote:
> On Wed, Jan 22, 2014 at 10:54 +0800, [email protected] wrote:
>> From: Tien Hock Loh <[email protected]>
>>
>> Add driver support for Altera GPIO soft IP, including interrupts and I/O.
>> Tested on Altera CV SoC board using dipsw and LED using LED framework.
>>
>> Signed-off-by: Tien Hock Loh <[email protected]>
>> ---
>> .../devicetree/bindings/gpio/gpio-altera.txt | 42 +++
>> drivers/gpio/Kconfig | 7 +
>> drivers/gpio/Makefile | 1 +
>> drivers/gpio/gpio-altera.c | 420
>> +++++++++++++++++++++
>> 4 files changed, 470 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/gpio/gpio-altera.txt
>> create mode 100644 drivers/gpio/gpio-altera.c
> Since you not only introduce the driver, but do introduce the
> binding as well, I'd suggest to reflect this in the commit
> message. And put 'binding' into the subject line such that DT
> people can be aware they should have a look.
Yes, and you also do not have the correct DT email address too.
Please look at the updated MAINTAINERS file for the correct DT
BINDINGS address.
Dinh
>
>
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/gpio/gpio-altera.txt
>> @@ -0,0 +1,42 @@
>> +Altera GPIO controller bindings
>> +
>> +Required properties:
>> +- compatible:
>> + - "altr,pio-1.0"
>> +- reg: Physical base address and length of the controller's registers.
>> +- #gpio-cells : Should be 1
>> + - The first cell is the gpio offset number
>> +- gpio-controller : Marks the device node as a GPIO controller.
> Learning about required data types when reading the binding would
> be nice. So that DTS authors can tell whether a property is
> boolean, takes integers or strings, etc
>
>> +- #interrupt-cells : Should be 1.
>> + - The first cell is the GPIO offset number within the GPIO controller.
>> +- interrupts: Specify the interrupt.
>> +- interrupt-controller: Mark the device node as an interrupt controller
> Are these really 'required'? I'd expect those to be optional.
>
>> +
>> +Altera GPIO specific properties:
>> +- altr,gpio-bank-width: Width of the GPIO bank. This defines how many pins
>> the
>> + GPIO device has. Ranges between 1-32. Optional and defaults to 32 is not
>> + specified.
> In addition to being specific to the Altera GPIO implementation,
> aren't these optional, too?
>
>> +- altr,interrupt_trigger: Specifies the interrupt trigger type the GPIO
>> + hardware is synthesized. This field is required if the Altera GPIO
>> controller
>> + used has IRQ enabled as the interrupt type is not software controlled,
>> + but hardware synthesized. Required if GPIO is used as an interrupt
>> + controller. The value is defined in
>> <dt-bindings/interrupt-controller/irq.h>
>> + Only the following flags are supported:
>> + IRQ_TYPE_EDGE_RISING
>> + IRQ_TYPE_EDGE_FALLING
>> + IRQ_TYPE_EDGE_BOTH
>> + IRQ_TYPE_LEVEL_HIGH
> This text suggests that using the GPIO bank as an interrupt
> controller indeed is optional. As one would expect.
>
>> +
>> +Example:
>> +
>> +gpio_altr: gpio_altr {
> Should node names not be generic, i.e. "gpio"? While aliases do
> have specific names since they identify a specific node, to later
> reference it from other sites.
>
>> + compatible = "altr,pio-1.0";
>> + reg = <0xff200000 0x10>;
>> + interrupts = <0 45 4>;
>> + altr,gpio-bank-width = <32>;
>> + altr,interrupt_trigger = <IRQ_TYPE_EDGE_RISING>;
>> + #gpio-cells = <1>;
>> + gpio-controller;
>> + #interrupt-cells = <1>;
>> + interrupt-controller;
>> +};
>
> virtually yours
> Gerhard Sittig
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
