On 17/04/2014 16:55, Alexandre Belloni wrote:
> On 14/04/2014 at 10:43:12 +0200, Boris Brezillon wrote :
>> Define sam9x5 clocks in sam9x5 dt files and make use of them in peripheral
>> definitions.
>>
>> Signed-off-by: Boris BREZILLON <[email protected]>
>> ---
>> arch/arm/boot/dts/at91sam9x5.dtsi | 355
>> ++++++++++++++++++++++++++++++-
>> arch/arm/boot/dts/at91sam9x5_can.dtsi | 31 +++
>> arch/arm/boot/dts/at91sam9x5_isi.dtsi | 26 +++
>> arch/arm/boot/dts/at91sam9x5_lcd.dtsi | 26 +++
>> arch/arm/boot/dts/at91sam9x5_macb0.dtsi | 11 +
>> arch/arm/boot/dts/at91sam9x5_macb1.dtsi | 11 +
>> arch/arm/boot/dts/at91sam9x5_usart3.dtsi | 11 +
>> 7 files changed, 470 insertions(+), 1 deletion(-)
>> create mode 100644 arch/arm/boot/dts/at91sam9x5_can.dtsi
>> create mode 100644 arch/arm/boot/dts/at91sam9x5_isi.dtsi
>> create mode 100644 arch/arm/boot/dts/at91sam9x5_lcd.dtsi
>>
>> diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi
>> b/arch/arm/boot/dts/at91sam9x5.dtsi
>> index fc13c92..723daf6 100644
>> --- a/arch/arm/boot/dts/at91sam9x5.dtsi
>> +++ b/arch/arm/boot/dts/at91sam9x5.dtsi
>> @@ -14,6 +14,7 @@
>> #include <dt-bindings/pinctrl/at91.h>
>> #include <dt-bindings/interrupt-controller/irq.h>
>> #include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/clk/at91.h>
>>
>> / {
>> model = "Atmel AT91SAM9x5 family SoC";
>> @@ -51,6 +52,24 @@
>> reg = <0x20000000 0x10000000>;
>> };
>>
>> + slow_xtal: slow_xtal {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <0>;
>> + };
>> +
>> + main_xtal: main_xtal {
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <0>;
>> + };
>> +
>> + adc_op_clk: adc_op_clk{
>> + compatible = "fixed-clock";
>> + #clock-cells = <0>;
>> + clock-frequency = <5000000>;
>> + };
>> +
>> ahb {
>> compatible = "simple-bus";
>> #address-cells = <1>;
>> @@ -77,8 +96,272 @@
>> };
>>
>> pmc: pmc@fffffc00 {
>> - compatible = "atmel,at91rm9200-pmc";
>> + compatible = "atmel,at91sam9x5-pmc";
>> reg = <0xfffffc00 0x100>;
>> + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + interrupt-controller;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + #interrupt-cells = <1>;
>> +
>> + main_rc_osc: main_rc_osc {
>> + compatible =
>> "atmel,at91sam9x5-clk-main-rc-osc";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc
>> AT91_PMC_MOSCRCS>;
>> + clock-frequency = <12000000>;
>> + clock-accuracy = <50000000>;
>> + };
>> +
>> + main_osc: main_osc {
>> + compatible =
>> "atmel,at91sam9x5-clk-main-osc";
> I know I acked the patch but after having a closer look, I think you are
> using a compatible string that doesn't exist at all here.
You're right, this should be "atmel,at91rm9200-clk-main-osc".
BTW, the same bug is present in the sam9n12 patch series :-).
I'll fix it.
Thanks.
Boris
>
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc
>> AT91_PMC_MOSCS>;
>> + clocks = <&main_xtal>;
>> + };
>> +
>> + main: mainck {
>> + compatible =
>> "atmel,at91sam9x5-clk-main";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc
>> AT91_PMC_MOSCSELS>;
>> + clocks = <&main_rc_osc>, <&main_osc>;
>> + };
>> +
>> + plla: pllack {
>> + compatible = "atmel,at91rm9200-clk-pll";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc
>> AT91_PMC_LOCKA>;
>> + clocks = <&main>;
>> + reg = <0>;
>> + atmel,clk-input-range = <2000000
>> 32000000>;
>> + #atmel,pll-clk-output-range-cells = <4>;
>> + atmel,pll-clk-output-ranges =
>> <745000000 800000000 0 0
>> +
>> 695000000 750000000 1 0
>> +
>> 645000000 700000000 2 0
>> +
>> 595000000 650000000 3 0
>> +
>> 545000000 600000000 0 1
>> +
>> 495000000 555000000 1 1
>> +
>> 445000000 500000000 1 2
>> +
>> 400000000 450000000 1 3>;
>> + };
>> +
>> + plladiv: plladivck {
>> + compatible =
>> "atmel,at91sam9x5-clk-plldiv";
>> + #clock-cells = <0>;
>> + clocks = <&plla>;
>> + };
>> +
>> + utmi: utmick {
>> + compatible =
>> "atmel,at91sam9x5-clk-utmi";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc
>> AT91_PMC_LOCKU>;
>> + clocks = <&main>;
>> + };
>> +
>> + mck: masterck {
>> + compatible =
>> "atmel,at91sam9x5-clk-master";
>> + #clock-cells = <0>;
>> + interrupts-extended = <&pmc
>> AT91_PMC_MCKRDY>;
>> + clocks = <&clk32k>, <&main>,
>> <&plladiv>, <&utmi>;
>> + atmel,clk-output-range = <0 133333333>;
>> + atmel,clk-divisors = <1 2 4 3>;
>> + atmel,master-clk-have-div3-pres;
>> + };
>> +
>> + usb: usbck {
>> + compatible = "atmel,at91sam9x5-clk-usb";
>> + #clock-cells = <0>;
>> + clocks = <&plladiv>, <&utmi>;
>> + };
>> +
>> + prog: progck {
>> + compatible =
>> "atmel,at91sam9x5-clk-programmable";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + interrupt-parent = <&pmc>;
>> + clocks = <&clk32k>, <&main>,
>> <&plladiv>, <&utmi>, <&mck>;
>> +
>> + prog0: prog0 {
>> + #clock-cells = <0>;
>> + reg = <0>;
>> + interrupts =
>> <AT91_PMC_PCKRDY(0)>;
>> + };
>> +
>> + prog1: prog1 {
>> + #clock-cells = <0>;
>> + reg = <1>;
>> + interrupts =
>> <AT91_PMC_PCKRDY(1)>;
>> + };
>> + };
>> +
>> + smd: smdclk {
>> + compatible = "atmel,at91sam9x5-clk-smd";
>> + #clock-cells = <0>;
>> + clocks = <&plladiv>, <&utmi>;
>> + };
>> +
>> + systemck {
>> + compatible =
>> "atmel,at91rm9200-clk-system";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + ddrck: ddrck {
>> + #clock-cells = <0>;
>> + reg = <2>;
>> + clocks = <&mck>;
>> + };
>> +
>> + smdck: smdck {
>> + #clock-cells = <0>;
>> + reg = <4>;
>> + clocks = <&smd>;
>> + };
>> +
>> + uhpck: uhpck {
>> + #clock-cells = <0>;
>> + reg = <6>;
>> + clocks = <&usb>;
>> + };
>> +
>> + udpck: udpck {
>> + #clock-cells = <0>;
>> + reg = <7>;
>> + clocks = <&usb>;
>> + };
>> +
>> + pck0: pck0 {
>> + #clock-cells = <0>;
>> + reg = <8>;
>> + clocks = <&prog0>;
>> + };
>> +
>> + pck1: pck1 {
>> + #clock-cells = <0>;
>> + reg = <9>;
>> + clocks = <&prog1>;
>> + };
>> + };
>> +
>> + periphck {
>> + compatible =
>> "atmel,at91sam9x5-clk-peripheral";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + clocks = <&mck>;
>> +
>> + pioAB_clk: pioAB_clk {
>> + #clock-cells = <0>;
>> + reg = <2>;
>> + };
>> +
>> + pioCD_clk: pioCD_clk {
>> + #clock-cells = <0>;
>> + reg = <3>;
>> + };
>> +
>> + smd_clk: smd_clk {
>> + #clock-cells = <0>;
>> + reg = <4>;
>> + };
>> +
>> + usart0_clk: usart0_clk {
>> + #clock-cells = <0>;
>> + reg = <5>;
>> + };
>> +
>> + usart1_clk: usart1_clk {
>> + #clock-cells = <0>;
>> + reg = <6>;
>> + };
>> +
>> + usart2_clk: usart2_clk {
>> + #clock-cells = <0>;
>> + reg = <7>;
>> + };
>> +
>> + twi0_clk: twi0_clk {
>> + reg = <9>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + twi1_clk: twi1_clk {
>> + #clock-cells = <0>;
>> + reg = <10>;
>> + };
>> +
>> + twi2_clk: twi2_clk {
>> + #clock-cells = <0>;
>> + reg = <11>;
>> + };
>> +
>> + mci0_clk: mci0_clk {
>> + #clock-cells = <0>;
>> + reg = <12>;
>> + };
>> +
>> + spi0_clk: spi0_clk {
>> + #clock-cells = <0>;
>> + reg = <13>;
>> + };
>> +
>> + spi1_clk: spi1_clk {
>> + #clock-cells = <0>;
>> + reg = <14>;
>> + };
>> +
>> + uart0_clk: uart0_clk {
>> + #clock-cells = <0>;
>> + reg = <15>;
>> + };
>> +
>> + uart1_clk: uart1_clk {
>> + #clock-cells = <0>;
>> + reg = <16>;
>> + };
>> +
>> + tcb0_clk: tcb0_clk {
>> + #clock-cells = <0>;
>> + reg = <17>;
>> + };
>> +
>> + pwm_clk: pwm_clk {
>> + #clock-cells = <0>;
>> + reg = <18>;
>> + };
>> +
>> + adc_clk: adc_clk {
>> + #clock-cells = <0>;
>> + reg = <19>;
>> + };
>> +
>> + dma0_clk: dma0_clk {
>> + #clock-cells = <0>;
>> + reg = <20>;
>> + };
>> +
>> + dma1_clk: dma1_clk {
>> + #clock-cells = <0>;
>> + reg = <21>;
>> + };
>> +
>> + uhphs_clk: uhphs_clk {
>> + #clock-cells = <0>;
>> + reg = <22>;
>> + };
>> +
>> + udphs_clk: udphs_clk {
>> + #clock-cells = <0>;
>> + reg = <23>;
>> + };
>> +
>> + mci1_clk: mci1_clk {
>> + #clock-cells = <0>;
>> + reg = <26>;
>> + };
>> +
>> + ssc0_clk: ssc0_clk {
>> + #clock-cells = <0>;
>> + reg = <28>;
>> + };
>> + };
>> };
>>
>> rstc@fffffe00 {
>> @@ -95,18 +378,47 @@
>> compatible = "atmel,at91sam9260-pit";
>> reg = <0xfffffe30 0xf>;
>> interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> + clocks = <&mck>;
>> + };
>> +
>> + sckc@fffffe50 {
>> + compatible = "atmel,at91sam9x5-sckc";
>> + reg = <0xfffffe50 0x4>;
>> +
>> + slow_osc: slow_osc {
>> + compatible =
>> "atmel,at91sam9x5-clk-slow-osc";
>> + #clock-cells = <0>;
>> + clocks = <&slow_xtal>;
>> + };
>> +
>> + slow_rc_osc: slow_rc_osc {
>> + compatible =
>> "atmel,at91sam9x5-clk-slow-rc-osc";
>> + #clock-cells = <0>;
>> + clock-frequency = <32768>;
>> + clock-accuracy = <50000000>;
>> + };
>> +
>> + clk32k: slck {
>> + compatible =
>> "atmel,at91sam9x5-clk-slow";
>> + #clock-cells = <0>;
>> + clocks = <&slow_rc_osc>, <&slow_osc>;
>> + };
>> };
>>
>> tcb0: timer@f8008000 {
>> compatible = "atmel,at91sam9x5-tcb";
>> reg = <0xf8008000 0x100>;
>> interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
>> + clocks = <&tcb0_clk>;
>> + clock-names = "t0_clk";
>> };
>>
>> tcb1: timer@f800c000 {
>> compatible = "atmel,at91sam9x5-tcb";
>> reg = <0xf800c000 0x100>;
>> interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
>> + clocks = <&tcb0_clk>;
>> + clock-names = "t0_clk";
>> };
>>
>> dma0: dma-controller@ffffec00 {
>> @@ -114,6 +426,8 @@
>> reg = <0xffffec00 0x200>;
>> interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
>> #dma-cells = <2>;
>> + clocks = <&dma0_clk>;
>> + clock-names = "dma_clk";
>> };
>>
>> dma1: dma-controller@ffffee00 {
>> @@ -121,6 +435,8 @@
>> reg = <0xffffee00 0x200>;
>> interrupts = <21 IRQ_TYPE_LEVEL_HIGH 0>;
>> #dma-cells = <2>;
>> + clocks = <&dma1_clk>;
>> + clock-names = "dma_clk";
>> };
>>
>> pinctrl@fffff400 {
>> @@ -453,6 +769,7 @@
>> gpio-controller;
>> interrupt-controller;
>> #interrupt-cells = <2>;
>> + clocks = <&pioAB_clk>;
>> };
>>
>> pioB: gpio@fffff600 {
>> @@ -464,6 +781,7 @@
>> #gpio-lines = <19>;
>> interrupt-controller;
>> #interrupt-cells = <2>;
>> + clocks = <&pioAB_clk>;
>> };
>>
>> pioC: gpio@fffff800 {
>> @@ -474,6 +792,7 @@
>> gpio-controller;
>> interrupt-controller;
>> #interrupt-cells = <2>;
>> + clocks = <&pioCD_clk>;
>> };
>>
>> pioD: gpio@fffffa00 {
>> @@ -485,6 +804,7 @@
>> #gpio-lines = <22>;
>> interrupt-controller;
>> #interrupt-cells = <2>;
>> + clocks = <&pioCD_clk>;
>> };
>> };
>>
>> @@ -497,6 +817,8 @@
>> dma-names = "tx", "rx";
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
>> + clocks = <&ssc0_clk>;
>> + clock-names = "pclk";
>> status = "disabled";
>> };
>>
>> @@ -507,6 +829,8 @@
>> dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(0)>;
>> dma-names = "rxtx";
>> pinctrl-names = "default";
>> + clocks = <&mci0_clk>;
>> + clock-names = "mci_clk";
>> #address-cells = <1>;
>> #size-cells = <0>;
>> status = "disabled";
>> @@ -519,6 +843,8 @@
>> dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(0)>;
>> dma-names = "rxtx";
>> pinctrl-names = "default";
>> + clocks = <&mci1_clk>;
>> + clock-names = "mci_clk";
>> #address-cells = <1>;
>> #size-cells = <0>;
>> status = "disabled";
>> @@ -530,6 +856,8 @@
>> interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_dbgu>;
>> + clocks = <&mck>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>>
>> @@ -539,6 +867,8 @@
>> interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_usart0>;
>> + clocks = <&usart0_clk>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>>
>> @@ -548,6 +878,8 @@
>> interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_usart1>;
>> + clocks = <&usart1_clk>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>>
>> @@ -557,6 +889,8 @@
>> interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_usart2>;
>> + clocks = <&usart2_clk>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>>
>> @@ -571,6 +905,7 @@
>> #size-cells = <0>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_i2c0>;
>> + clocks = <&twi0_clk>;
>> status = "disabled";
>> };
>>
>> @@ -585,6 +920,7 @@
>> #size-cells = <0>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_i2c1>;
>> + clocks = <&twi1_clk>;
>> status = "disabled";
>> };
>>
>> @@ -599,6 +935,7 @@
>> #size-cells = <0>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_i2c2>;
>> + clocks = <&twi2_clk>;
>> status = "disabled";
>> };
>>
>> @@ -608,6 +945,8 @@
>> interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_uart0>;
>> + clocks = <&uart0_clk>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>>
>> @@ -617,6 +956,8 @@
>> interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_uart1>;
>> + clocks = <&uart1_clk>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>>
>> @@ -626,6 +967,9 @@
>> compatible = "atmel,at91sam9260-adc";
>> reg = <0xf804c000 0x100>;
>> interrupts = <19 IRQ_TYPE_LEVEL_HIGH 0>;
>> + clocks = <&adc_clk>,
>> + <&adc_op_clk>;
>> + clock-names = "adc_clk", "adc_op_clk";
>> atmel,adc-use-external-triggers;
>> atmel,adc-channels-used = <0xffff>;
>> atmel,adc-vref = <3300>;
>> @@ -673,6 +1017,8 @@
>> dma-names = "tx", "rx";
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_spi0>;
>> + clocks = <&spi0_clk>;
>> + clock-names = "spi_clk";
>> status = "disabled";
>> };
>>
>> @@ -687,6 +1033,8 @@
>> dma-names = "tx", "rx";
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_spi1>;
>> + clocks = <&spi1_clk>;
>> + clock-names = "spi_clk";
>> status = "disabled";
>> };
>>
>> @@ -805,6 +1153,9 @@
>> compatible = "atmel,at91rm9200-ohci", "usb-ohci";
>> reg = <0x00600000 0x100000>;
>> interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
>> + clocks = <&usb>, <&uhphs_clk>, <&udphs_clk>,
>> + <&uhpck>;
>> + clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck";
>> status = "disabled";
>> };
>>
>> @@ -812,6 +1163,8 @@
>> compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
>> reg = <0x00700000 0x100000>;
>> interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
>> + clocks = <&usb>, <&uhphs_clk>, <&uhpck>;
>> + clock-names = "usb_clk", "ehci_clk", "uhpck";
>> status = "disabled";
>> };
>> };
>> diff --git a/arch/arm/boot/dts/at91sam9x5_can.dtsi
>> b/arch/arm/boot/dts/at91sam9x5_can.dtsi
>> new file mode 100644
>> index 0000000..f44ab77
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91sam9x5_can.dtsi
>> @@ -0,0 +1,31 @@
>> +/*
>> + * at91sam9x5_macb0.dtsi - Device Tree Include file for AT91SAM9x5 SoC with
>> 1
>> + * Ethernet interface.
>> + *
>> + * Copyright (C) 2013 Boris BREZILLON <[email protected]>
>> + *
>> + * Licensed under GPLv2.
>> + */
>> +
>> +#include <dt-bindings/pinctrl/at91.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +
>> +/ {
>> + ahb {
>> + apb {
>> + pmc: pmc@fffffc00 {
>> + periphck {
>> + can0_clk: can0_clk {
>> + #clock-cells = <0>;
>> + reg = <29>;
>> + };
>> +
>> + can1_clk: can1_clk {
>> + #clock-cells = <0>;
>> + reg = <30>;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +};
>> diff --git a/arch/arm/boot/dts/at91sam9x5_isi.dtsi
>> b/arch/arm/boot/dts/at91sam9x5_isi.dtsi
>> new file mode 100644
>> index 0000000..98bc877
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91sam9x5_isi.dtsi
>> @@ -0,0 +1,26 @@
>> +/*
>> + * at91sam9x5_isi.dtsi - Device Tree Include file for AT91SAM9x5 SoC with an
>> + * Image Sensor Interface.
>> + *
>> + * Copyright (C) 2013 Boris BREZILLON <[email protected]>
>> + *
>> + * Licensed under GPLv2.
>> + */
>> +
>> +#include <dt-bindings/pinctrl/at91.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +
>> +/ {
>> + ahb {
>> + apb {
>> + pmc: pmc@fffffc00 {
>> + periphck {
>> + isi_clk: isi_clk {
>> + #clock-cells = <0>;
>> + reg = <25>;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +};
>> diff --git a/arch/arm/boot/dts/at91sam9x5_lcd.dtsi
>> b/arch/arm/boot/dts/at91sam9x5_lcd.dtsi
>> new file mode 100644
>> index 0000000..485302e
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/at91sam9x5_lcd.dtsi
>> @@ -0,0 +1,26 @@
>> +/*
>> + * at91sam9x5_lcd.dtsi - Device Tree Include file for AT91SAM9x5 SoC with an
>> + * LCD controller.
>> + *
>> + * Copyright (C) 2013 Boris BREZILLON <[email protected]>
>> + *
>> + * Licensed under GPLv2.
>> + */
>> +
>> +#include <dt-bindings/pinctrl/at91.h>
>> +#include <dt-bindings/interrupt-controller/irq.h>
>> +
>> +/ {
>> + ahb {
>> + apb {
>> + pmc: pmc@fffffc00 {
>> + periphck {
>> + lcdc_clk: lcdc_clk {
>> + #clock-cells = <0>;
>> + reg = <25>;
>> + };
>> + };
>> + };
>> + };
>> + };
>> +};
>> diff --git a/arch/arm/boot/dts/at91sam9x5_macb0.dtsi
>> b/arch/arm/boot/dts/at91sam9x5_macb0.dtsi
>> index 55731ff..57e89d1 100644
>> --- a/arch/arm/boot/dts/at91sam9x5_macb0.dtsi
>> +++ b/arch/arm/boot/dts/at91sam9x5_macb0.dtsi
>> @@ -43,12 +43,23 @@
>> };
>> };
>>
>> + pmc: pmc@fffffc00 {
>> + periphck {
>> + macb0_clk: macb0_clk {
>> + #clock-cells = <0>;
>> + reg = <24>;
>> + };
>> + };
>> + };
>> +
>> macb0: ethernet@f802c000 {
>> compatible = "cdns,at32ap7000-macb",
>> "cdns,macb";
>> reg = <0xf802c000 0x100>;
>> interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_macb0_rmii>;
>> + clocks = <&macb0_clk>, <&macb0_clk>;
>> + clock-names = "hclk", "pclk";
>> status = "disabled";
>> };
>> };
>> diff --git a/arch/arm/boot/dts/at91sam9x5_macb1.dtsi
>> b/arch/arm/boot/dts/at91sam9x5_macb1.dtsi
>> index 77425a6..663676c 100644
>> --- a/arch/arm/boot/dts/at91sam9x5_macb1.dtsi
>> +++ b/arch/arm/boot/dts/at91sam9x5_macb1.dtsi
>> @@ -31,12 +31,23 @@
>> };
>> };
>>
>> + pmc: pmc@fffffc00 {
>> + periphck {
>> + macb1_clk: macb1_clk {
>> + #clock-cells = <0>;
>> + reg = <27>;
>> + };
>> + };
>> + };
>> +
>> macb1: ethernet@f8030000 {
>> compatible = "cdns,at32ap7000-macb",
>> "cdns,macb";
>> reg = <0xf8030000 0x100>;
>> interrupts = <27 IRQ_TYPE_LEVEL_HIGH 3>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_macb1_rmii>;
>> + clocks = <&macb1_clk>, <&macb1_clk>;
>> + clock-names = "hclk", "pclk";
>> status = "disabled";
>> };
>> };
>> diff --git a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
>> b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
>> index 6801106..140217a5 100644
>> --- a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
>> +++ b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
>> @@ -42,12 +42,23 @@
>> };
>> };
>>
>> + pmc: pmc@fffffc00 {
>> + periphck {
>> + usart3_clk: usart3_clk {
>> + #clock-cells = <0>;
>> + reg = <8>;
>> + };
>> + };
>> + };
>> +
>> usart3: serial@f8028000 {
>> compatible = "atmel,at91sam9260-usart";
>> reg = <0xf8028000 0x200>;
>> interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_usart3>;
>> + clocks = <&usart3_clk>;
>> + clock-names = "usart";
>> status = "disabled";
>> };
>> };
>> --
>> 1.8.3.2
>>
--
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
