2014-05-05 14:47 GMT-07:00 Iyappan Subramanian <[email protected]>:
> This patch adds documentation for APM X-Gene SoC ethernet DTS binding.
>
> Signed-off-by: Iyappan Subramanian <[email protected]>
> Signed-off-by: Ravi Patel <[email protected]>
> Signed-off-by: Keyur Chudgar <[email protected]>
> ---
> .../devicetree/bindings/net/apm-xgene-enet.txt | 66
> ++++++++++++++++++++
> 1 file changed, 66 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/apm-xgene-enet.txt
>
> diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt
> b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt
> new file mode 100644
> index 0000000..9ad6fe1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt
> @@ -0,0 +1,66 @@
> +APM X-Gene SoC Ethernet nodes
> +
> +Ethernet nodes are defined to describe on-chip ethernet interfaces in
> +APM X-Gene SoC.
> +
> +Required properties:
> +- compatible: Should be "apm,xgene-enet"
> +- reg: First resource is the ethernet base register set
> + Second resource is the ring base register set
> + Third resource is the ring command register set
> +- interrupts: Ethernet main interrupt
> +- clocks: Reference to the clock entry.
> +- local-mac-address: Ethernet MAC address.
> +- phy-connection-type: Ethernet MII mode.
- phy-handle is not listed anywhere, yet, present in the example you give.
> +
> +- mdio device tree subnode: When the X-Gene SoC has a phy connected to its
> local
> + mdio, there must be device tree subnode with the following
> + required properties:
In that specific case, 'phy-handle' becomes an optional property.
> +
> + - compatible: Must be "apm,xgene-mdio".
> + - #address-cells: Must be <1>.
> + - #size-cells: Must be <0>.
> +
> + For the phy on the mdio bus, there must be a node with the following
> + fields:
> +
> + - reg: phy id used to communicate to phy.
Better refer to Documentation/devicetree/bindings/ethernet/phy.txt
which contains a more exhaustive binding description for Ethernet PHY
nodes.
> +
> +Optional properties:
> +- status : Should be "ok" or "disabled" for enabled/disabled.
> + Default is "ok".
> +
> +Example:
> + menetclk: menetclk {
> + compatible = "apm,xgene-device-clock";
> + clock-output-names = "menetclk";
> + status = "ok";
> + };
> +
> + menet: ethernet@17020000 {
> + compatible = "apm,xgene-enet";
> + status = "disabled";
> + reg = <0x0 0x17020000 0x0 0xd100>,
> + <0x0 0X17030000 0x0 0X400>,
> + <0x0 0X10000000 0x0 0X200>;
Since you have mutliple values in your 'reg' property, you could also
provide an optional 'reg-names' which documents what the register
ranges are about.
> + interrupts = <0x0 0x3c 0x4>;
> + clocks = <&menetclk 0>;
> + local-mac-address = [00 01 73 00 00 01];
> + phy-connection-type = "rgmii";
> + phy-handle = <&menetphy>;
> + mdio {
> + compatible = "apm,xgene-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + menetphy: menetphy@3 {
This PHY node is missing a compatible string as described in
Documentation/devicetree/bindings/net/ethernet/phy.txt. Your binding
should also link to that documentation for
> + reg = <0x3>;
> + };
> +
> + };
> + };
> +
> +/* Board-specific peripheral configurations */
> +
> +&menet {
> + status = "ok";
> +};
> --
> 1.7.9.5
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
