Add the necessary nodes to enable the LCD controller and the LCD panel that is attached to the Texas Instruments AM335x EVMSK platform. Also setup the necessary pin mux within the DT file to drive the LCD connector and add the correct pinmux settings for the lcd pins to be configured to when the SoC goes into sleep state for the minimum power consumption.
For the sleep mode LCD pin settings, MUX_MODE7 is chosen as this corresponds to switching the pins into input GPIO's with an internal pulldown. Which has been determined to offer the lowest power solution vs leaving the pins configured in LCD mode. Signed-off-by: Darren Etheridge <[email protected]> --- v2: Fixed up the incorrect label ordering in the pinmux comments for LCD pins 16 through 23 as reported by Wolfram Sang <[email protected]> arch/arm/boot/dts/am335x-evmsk.dts | 105 +++++++++++++++++++++++++++++++++++++ 1 file changed, 105 insertions(+) diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index ab23885..d99c1b1 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -138,12 +138,113 @@ "Headphone Jack", "HPLOUT", "Headphone Jack", "HPROUT"; }; + + panel { + compatible = "ti,tilcdc,panel"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&lcd_pins_default>; + pinctrl-1 = <&lcd_pins_sleep>; + status = "okay"; + panel-info { + ac-bias = <255>; + ac-bias-intrpt = <0>; + dma-burst-sz = <16>; + bpp = <32>; + fdd = <0x80>; + sync-edge = <0>; + sync-ctrl = <1>; + raster-order = <0>; + fifo-th = <0>; + }; + display-timings { + 480x272 { + hactive = <480>; + vactive = <272>; + hback-porch = <43>; + hfront-porch = <8>; + hsync-len = <4>; + vback-porch = <12>; + vfront-porch = <4>; + vsync-len = <10>; + clock-frequency = <9000000>; + hsync-active = <0>; + vsync-active = <0>; + }; + }; + }; }; &am33xx_pinmux { pinctrl-names = "default"; pinctrl-0 = <&gpio_keys_s0 &clkout2_pin>; + lcd_pins_default: lcd_pins_default { + pinctrl-single,pins = < + 0x20 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data23 */ + 0x24 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad9.lcd_data22 */ + 0x28 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad10.lcd_data21 */ + 0x2c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad11.lcd_data20 */ + 0x30 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad12.lcd_data19 */ + 0x34 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad13.lcd_data18 */ + 0x38 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad14.lcd_data17 */ + 0x3c (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad15.lcd_data16 */ + 0xa0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data0.lcd_data0 */ + 0xa4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data1.lcd_data1 */ + 0xa8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data2.lcd_data2 */ + 0xac (PIN_OUTPUT | MUX_MODE0) /* lcd_data3.lcd_data3 */ + 0xb0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data4.lcd_data4 */ + 0xb4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data5.lcd_data5 */ + 0xb8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data6.lcd_data6 */ + 0xbc (PIN_OUTPUT | MUX_MODE0) /* lcd_data7.lcd_data7 */ + 0xc0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data8.lcd_data8 */ + 0xc4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data9.lcd_data9 */ + 0xc8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data10.lcd_data10 */ + 0xcc (PIN_OUTPUT | MUX_MODE0) /* lcd_data11.lcd_data11 */ + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* lcd_data12.lcd_data12 */ + 0xd4 (PIN_OUTPUT | MUX_MODE0) /* lcd_data13.lcd_data13 */ + 0xd8 (PIN_OUTPUT | MUX_MODE0) /* lcd_data14.lcd_data14 */ + 0xdc (PIN_OUTPUT | MUX_MODE0) /* lcd_data15.lcd_data15 */ + 0xe0 (PIN_OUTPUT | MUX_MODE0) /* lcd_vsync.lcd_vsync */ + 0xe4 (PIN_OUTPUT | MUX_MODE0) /* lcd_hsync.lcd_hsync */ + 0xe8 (PIN_OUTPUT | MUX_MODE0) /* lcd_pclk.lcd_pclk */ + 0xec (PIN_OUTPUT | MUX_MODE0) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + + lcd_pins_sleep: lcd_pins_sleep { + pinctrl-single,pins = < + 0x20 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad8.lcd_data23 */ + 0x24 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad9.lcd_data22 */ + 0x28 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad10.lcd_data21 */ + 0x2c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad11.lcd_data20 */ + 0x30 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad12.lcd_data19 */ + 0x34 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad13.lcd_data18 */ + 0x38 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad14.lcd_data17 */ + 0x3c (PIN_INPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad15.lcd_data16 */ + 0xa0 (PULL_DISABLE | MUX_MODE7) /* lcd_data0.lcd_data0 */ + 0xa4 (PULL_DISABLE | MUX_MODE7) /* lcd_data1.lcd_data1 */ + 0xa8 (PULL_DISABLE | MUX_MODE7) /* lcd_data2.lcd_data2 */ + 0xac (PULL_DISABLE | MUX_MODE7) /* lcd_data3.lcd_data3 */ + 0xb0 (PULL_DISABLE | MUX_MODE7) /* lcd_data4.lcd_data4 */ + 0xb4 (PULL_DISABLE | MUX_MODE7) /* lcd_data5.lcd_data5 */ + 0xb8 (PULL_DISABLE | MUX_MODE7) /* lcd_data6.lcd_data6 */ + 0xbc (PULL_DISABLE | MUX_MODE7) /* lcd_data7.lcd_data7 */ + 0xc0 (PULL_DISABLE | MUX_MODE7) /* lcd_data8.lcd_data8 */ + 0xc4 (PULL_DISABLE | MUX_MODE7) /* lcd_data9.lcd_data9 */ + 0xc8 (PULL_DISABLE | MUX_MODE7) /* lcd_data10.lcd_data10 */ + 0xcc (PULL_DISABLE | MUX_MODE7) /* lcd_data11.lcd_data11 */ + 0xd0 (PULL_DISABLE | MUX_MODE7) /* lcd_data12.lcd_data12 */ + 0xd4 (PULL_DISABLE | MUX_MODE7) /* lcd_data13.lcd_data13 */ + 0xd8 (PULL_DISABLE | MUX_MODE7) /* lcd_data14.lcd_data14 */ + 0xdc (PULL_DISABLE | MUX_MODE7) /* lcd_data15.lcd_data15 */ + 0xe0 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_vsync.lcd_vsync */ + 0xe4 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_hsync.lcd_hsync */ + 0xe8 (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_pclk.lcd_pclk */ + 0xec (PIN_INPUT_PULLDOWN | MUX_MODE7) /* lcd_ac_bias_en.lcd_ac_bias_en */ + >; + }; + + user_leds_s0: user_leds_s0 { pinctrl-single,pins = < 0x10 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_ad4.gpio1_4 */ @@ -560,3 +661,7 @@ ti,wire-config = <0x00 0x11 0x22 0x33>; }; }; + +&lcdc { + status = "okay"; +}; -- 1.8.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
