On Wed, May 28, 2014 at 08:23:09PM +0900, Yoshihiro Shimoda wrote:
> The R-Car H2 and M2 SoCs come with an xHCI controller that requires
> some specific initializations related to the firmware downloading and
> some specific registers. This patch adds the support for this special
> configuration as an xHCI quirk executed during probe and start.
>
> Signed-off-by: Yoshihiro Shimoda <[email protected]>
> ---
> drivers/usb/host/Kconfig | 8 +++
> drivers/usb/host/Makefile | 3 +
> drivers/usb/host/xhci-plat.c | 18 +++++
> drivers/usb/host/xhci-rcar.c | 160
> ++++++++++++++++++++++++++++++++++++++++++
> drivers/usb/host/xhci-rcar.h | 27 +++++++
> 5 files changed, 216 insertions(+)
> create mode 100644 drivers/usb/host/xhci-rcar.c
> create mode 100644 drivers/usb/host/xhci-rcar.h
>
> diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
> index 61b7817..537d9e1 100644
> --- a/drivers/usb/host/Kconfig
> +++ b/drivers/usb/host/Kconfig
> @@ -37,6 +37,14 @@ config USB_XHCI_MVEBU
> Say 'Y' to enable the support for the xHCI host controller
> found in Marvell Armada 375/38x ARM SOCs.
>
> +config USB_XHCI_RCAR
> + tristate "xHCI support for Renesas R-Car SoCs"
> + select USB_XHCI_PLATFORM
> + depends on ARCH_SHMOBILE || COMPILE_TEST
> + ---help---
> + Say 'Y' to enable the support for the xHCI host controller
> + found in Renesas R-Car ARM SoCs.
> +
> endif # USB_XHCI_HCD
>
> config USB_EHCI_HCD
> diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
> index af89a90..144c038 100644
> --- a/drivers/usb/host/Makefile
> +++ b/drivers/usb/host/Makefile
> @@ -22,6 +22,9 @@ ifneq ($(CONFIG_USB_XHCI_PLATFORM), )
> ifneq ($(CONFIG_USB_XHCI_MVEBU), )
> xhci-hcd-y += xhci-mvebu.o
> endif
> +ifneq ($(CONFIG_USB_XHCI_RCAR), )
> + xhci-hcd-y += xhci-rcar.o
> +endif
> endif
>
> obj-$(CONFIG_USB_WHCI_HCD) += whci/
> diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c
> index 1389370..7c714c1 100644
> --- a/drivers/usb/host/xhci-plat.c
> +++ b/drivers/usb/host/xhci-plat.c
> @@ -21,6 +21,7 @@
>
> #include "xhci.h"
> #include "xhci-mvebu.h"
> +#include "xhci-rcar.h"
>
> static void xhci_plat_quirks(struct device *dev, struct xhci_hcd *xhci)
> {
> @@ -40,6 +41,12 @@ static int xhci_plat_setup(struct usb_hcd *hcd)
>
> static int xhci_plat_start(struct usb_hcd *hcd)
> {
> + struct device_node *of_node = hcd->self.controller->of_node;
> +
> + if (of_device_is_compatible(of_node, "renesas,xhci-r8a7790") ||
> + of_device_is_compatible(of_node, "renesas,xhci-r8a7791"))
> + xhci_rcar_start(hcd);
> +
> return xhci_run(hcd);
> }
>
> @@ -181,6 +188,15 @@ static int xhci_plat_probe(struct platform_device *pdev)
> goto disable_phy;
> }
>
> + if (of_device_is_compatible(pdev->dev.of_node,
> + "renesas,xhci-r8a7790") ||
> + of_device_is_compatible(pdev->dev.of_node,
> + "renesas,xhci-r8a7791")) {
> + ret = xhci_rcar_init_quirk(pdev);
> + if (ret)
> + goto power_off_phy;
> + }
> +
> ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
> if (ret)
> goto power_off_phy;
> @@ -295,6 +311,8 @@ static const struct of_device_id usb_xhci_of_match[] = {
> { .compatible = "xhci-platform" },
> { .compatible = "marvell,armada-375-xhci"},
> { .compatible = "marvell,armada-380-xhci"},
> + { .compatible = "renesas,xhci-r8a7790"},
> + { .compatible = "renesas,xhci-r8a7791"},
> { },
> };
> MODULE_DEVICE_TABLE(of, usb_xhci_of_match);
> diff --git a/drivers/usb/host/xhci-rcar.c b/drivers/usb/host/xhci-rcar.c
> new file mode 100644
> index 0000000..233726b
> --- /dev/null
> +++ b/drivers/usb/host/xhci-rcar.c
> @@ -0,0 +1,160 @@
> +/*
> + * xHCI host controller driver for R-Car SoCs
> + *
> + * Copyright (C) 2014 Renesas Electronics Corporation
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + */
> +
> +#include <linux/firmware.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/usb/phy.h>
> +
> +#include "xhci.h"
> +#include "xhci-rcar.h"
> +
> +#define FIRMWARE_NAME "r8a779x_usb3_v1.dlmem"
Shouldn't you also add a:
MODULE_FIRMWARE(FIRMWARE_NAME);
line to this file so that the automatic tools can pick it up properly?
thanks,
greg k-h
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
