Hummingboard has no over current hardware, so disable the over current detection for both ports.
Cubox-i has over current hardware, so appropriately configure this. Signed-off-by: Russell King <[email protected]> --- arch/arm/boot/dts/imx6dl-hummingboard.dts | 2 ++ arch/arm/boot/dts/imx6qdl-cubox-i.dtsi | 17 +++++++++++++---- 2 files changed, 15 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/imx6dl-hummingboard.dts b/arch/arm/boot/dts/imx6dl-hummingboard.dts index c8e51dd41b8f..d1c892e28296 100644 --- a/arch/arm/boot/dts/imx6dl-hummingboard.dts +++ b/arch/arm/boot/dts/imx6dl-hummingboard.dts @@ -181,11 +181,13 @@ }; &usbh1 { + disable-over-current; vbus-supply = <®_usbh1_vbus>; status = "okay"; }; &usbotg { + disable-over-current; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hummingboard_usbotg_id>; vbus-supply = <®_usbotg_vbus>; diff --git a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi b/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi index e8e781656b3f..298d0fdf8ebe 100644 --- a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi +++ b/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi @@ -130,16 +130,23 @@ fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>; }; + pinctrl_cubox_i_usbh1: cubox-i-usbh1 { + fsl,pins = <MX6QDL_PAD_GPIO_3__USB_H1_OC 0x1b0b0>; + }; + pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus { fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>; }; - pinctrl_cubox_i_usbotg_id: cubox-i-usbotg-id { + pinctrl_cubox_i_usbotg: cubox-i-usbotg { /* - * The Cubox-i pulls this low, but as it's pointless + * The Cubox-i pulls ID low, but as it's pointless * leaving it as a pull-up, even if it is just 10uA. */ - fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>; + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059 + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0 + >; }; pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus { @@ -173,13 +180,15 @@ }; &usbh1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_cubox_i_usbh1>; vbus-supply = <®_usbh1_vbus>; status = "okay"; }; &usbotg { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_cubox_i_usbotg_id>; + pinctrl-0 = <&pinctrl_cubox_i_usbotg>; vbus-supply = <®_usbotg_vbus>; status = "okay"; }; -- 1.8.3.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
