On Thu, Oct 16, 2014 at 09:26:23PM +0100, Marek Belisko wrote:
> Signed-off-by: H. Nikolaus Schaller <[email protected]>
> Signed-off-by: Marek Belisko <[email protected]>
> ---
> .../devicetree/bindings/misc/wi2wi,w2sg0004.txt | 44
> ++++++++++++++++++++++
> 1 file changed, 44 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/misc/wi2wi,w2sg0004.txt
>
> diff --git a/Documentation/devicetree/bindings/misc/wi2wi,w2sg0004.txt
> b/Documentation/devicetree/bindings/misc/wi2wi,w2sg0004.txt
> new file mode 100644
> index 0000000..e144441
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/misc/wi2wi,w2sg0004.txt
> @@ -0,0 +1,44 @@
> +Wi2Wi GPS module connected through UART
> +
> +Required properties:
> +- compatible: wi2wi,w2sg0004 or wi2wi,w2sg0084
> +- pinctrl: specify two states (default and monitor). One is the default
> (UART) mode
> + and the other is for monitoring the RX line by an interrupt
> +- on-off-gpio: the GPIO that controls the module's on-off toggle input
> +
> +Optional properties:
> +- lna-suppy: an (optional) LNA regulator that is enabled together with the
> GPS receiver
> +
> +example:
> +
> + gps_receiver: w2sg0004 {
> + compatible = "wi2wi,w2sg0004";
I couldn't spot "wi2wi" in
Documentation/devicetree/bindings/vendor-prefixes.txt (in mainline).
Could you please add it?
> + gpio-controller;
> + #gpio-cells = <2>;
As far as I can see, these properties aren't necessary. This only
consumes a GPIO, it doesn't provide any.
> +
> + pinctrl-names = "default", "monitor";
> + pinctrl-0 = <&uart2_pins>;
> + pinctrl-1 = <&uart2_rx_irq_pins>;
> +
> + interrupt-parent = <&gpio5>;
> + interrupts = <19 IRQ_TYPE_EDGE_FALLING>; /* GPIO_147: RX -
> trigger on arrival of start bit */
While interrupts is a standard property, please describe above how many
you expect and what their logical function is.
The only part I'm confused about is how the link to the UART is
described. I assume I'm just ignorant of some existing pattern.
Otherwise this looks ok.
Thanks,
Mark.
> + lna-supply = <&vsim>; /* LNA regulator */
> + on-off-gpio = <&gpio5 17 0>; /* GPIO_145: trigger for
> turning on/off w2sg0004 */
> +
> +&pinmux {
> +
> + uart2_pins: pinmux_uart2_pins {
> + pinctrl-single,pins = <
> + 0x14a (PIN_INPUT | MUX_MODE0) /*
> uart2_tx.uart2_rx */
> + 0x148 (PIN_OUTPUT | MUX_MODE0) /*
> uart2_tx.uart2_tx */
> + >;
> + };
> +
> + uart2_rx_irq_pins: pinmux_uart2_rx_irq_pins {
> + pinctrl-single,pins = <
> + /* switch RX to GPIO so that we can get interrupts by
> the start bit */
> + 0x14a (PIN_INPUT | MUX_MODE4) /*
> uart2_tx.uart2_rx */
> + >;
> + };
> +
> +}
> --
> 1.9.1
>
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
