New IGEP boards revisions will use another Wifi module, so this patch moves the DT nodes outside the common omap3-igep.dtsi file to specific DT for every board.
Signed-off-by: Enric Balletbo i Serra <[email protected]> --- arch/arm/boot/dts/omap3-igep.dtsi | 29 --------------------------- arch/arm/boot/dts/omap3-igep0020.dts | 39 ++++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/omap3-igep0030.dts | 39 ++++++++++++++++++++++++++++++++++++ 3 files changed, 78 insertions(+), 29 deletions(-) diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index 04a58ab..6118e7f 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -31,18 +31,6 @@ regulator-always-on; }; - lbee1usjyc_vmmc: lbee1usjyc_vmmc { - pinctrl-names = "default"; - pinctrl-0 = <&lbee1usjyc_pins>; - compatible = "regulator-fixed"; - regulator-name = "regulator-lbee1usjyc"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>; /* gpio_138 WIFI_PDN */ - startup-delay-us = <10000>; - enable-active-high; - vin-supply = <&vdd33>; - }; }; &omap3_pmx_core { @@ -60,15 +48,6 @@ >; }; - /* WiFi/BT combo */ - lbee1usjyc_pins: pinmux_lbee1usjyc_pins { - pinctrl-single,pins = < - 0x136 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat5.gpio_137 */ - 0x138 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat6.gpio_138 */ - 0x13a (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 */ - >; - }; - mcbsp2_pins: pinmux_mcbsp2_pins { pinctrl-single,pins = < 0x10c (PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx.mcbsp2_fsx */ @@ -223,14 +202,6 @@ bus-width = <4>; }; -&mmc2 { - pinctrl-names = "default"; - pinctrl-0 = <&mmc2_pins>; - vmmc-supply = <&lbee1usjyc_vmmc>; - bus-width = <4>; - non-removable; -}; - &mmc3 { status = "disabled"; }; diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index 75a3ac3..0d82f09 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -45,6 +45,27 @@ }; }; + /* Regulator to trigger the WIFI_PDN signal of the Wifi module */ + lbee1usjyc_pdn: lbee1usjyc_pdn { + compatible = "regulator-fixed"; + regulator-name = "regulator-lbee1usjyc-pdn"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>; /* gpio_138 - WIFI_PDN */ + startup-delay-us = <10000>; + enable-active-high; + }; + + /* Regulator to trigger the RESET_N_W signal of the Wifi module */ + lbee1usjyc_reset_n_w: lbee1usjyc_reset_n_w { + compatible = "regulator-fixed"; + regulator-name = "regulator-lbee1usjyc-reset-n-w"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 11 GPIO_ACTIVE_HIGH>; /* gpio_139 - RESET_N_W */ + enable-active-high; + }; + /* HS USB Port 1 Power */ hsusb1_power: hsusb1_power_reg { compatible = "regulator-fixed"; @@ -150,6 +171,14 @@ >; }; + lbee1usjyc_pins: pinmux_lbee1usjyc_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat5.gpio_137 - RESET_N_W */ + OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat6.gpio_138 - WIFI_PDN */ + OMAP3_CORE1_IOPAD(0x216a, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 - RST_N_B */ + >; + }; + uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */ @@ -218,6 +247,16 @@ }; }; +/* On board Wifi module */ +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins &lbee1usjyc_pins>; + vmmc-supply = <&lbee1usjyc_pdn>; + vmmc_aux-supply = <&lbee1usjyc_reset_n_w>; + bus-width = <4>; + non-removable; +}; + &uart2 { pinctrl-names = "default"; pinctrl-0 = <&uart2_pins>; diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts index d7527b6..cc2a374 100644 --- a/arch/arm/boot/dts/omap3-igep0030.dts +++ b/arch/arm/boot/dts/omap3-igep0030.dts @@ -44,9 +44,38 @@ default-state = "off"; }; }; + + /* Regulator to trigger the WIFI_PDN signal of the Wifi module */ + lbee1usjyc_pdn: lbee1usjyc_pdn { + compatible = "regulator-fixed"; + regulator-name = "regulator-lbee1usjyc-pdn"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>; /* gpio_138 - WIFI_PDN */ + startup-delay-us = <10000>; + enable-active-high; + }; + + /* Regulator to trigger the RESET_N_W signal of the Wifi module */ + lbee1usjyc_reset_n_w: lbee1usjyc_reset_n_w { + compatible = "regulator-fixed"; + regulator-name = "regulator-lbee1usjyc-reset-n-w"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio5 11 GPIO_ACTIVE_HIGH>; /* gpio_139 - RESET_N_W */ + enable-active-high; + }; }; &omap3_pmx_core { + lbee1usjyc_pins: pinmux_lbee1usjyc_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat5.gpio_137 - RESET_N_W */ + OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat6.gpio_138 - WIFI_PDN */ + OMAP3_CORE1_IOPAD(0x216a, PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 - RST_N_B */ + >; + }; + uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1) /* mcbsp3_dx.uart2_cts */ @@ -65,6 +94,16 @@ }; }; +/* On board Wifi module */ +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins &lbee1usjyc_pins>; + vmmc-supply = <&lbee1usjyc_pdn>; + vmmc_aux-supply = <&lbee1usjyc_reset_n_w>; + bus-width = <4>; + non-removable; +}; + &uart2 { pinctrl-names = "default"; pinctrl-0 = <&uart2_pins>; -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
