On 2015/1/15 12:39, Joe Perches wrote:
> On Wed, 2015-01-14 at 14:34 +0800, Ding Tianhong wrote:
>> Support Hisilicon hip04 ethernet driver, including 100M / 1000M controller.
>> The controller has no tx done interrupt, reclaim xmitted buffer in the poll.
>
> Mostly trivial comments:
>
>> +++ b/drivers/net/ethernet/hisilicon/hip04_eth.c
>
> []
>
>> +#define GMAC_MAX_PKT_LEN 1516
>
> []
>
>> +static int hip04_rx_poll(struct napi_struct *napi, int budget)
>> +{
> []
>> + while (cnt && !last) {
> []
>> + desc = (struct rx_desc *)skb->data;
>> + len = be16_to_cpu(desc->pkt_len);
>> + err = be32_to_cpu(desc->pkt_err);
>> +
>> + if (0 == len) {
>> + dev_kfree_skb_any(skb);
>> + last = true;
>> + } else if ((err & RX_PKT_ERR) || (len >= GMAC_MAX_PKT_LEN)) {
>
> Is this ">=" correct? Maybe it should be ">" ?
>
> []
>
>> +static irqreturn_t hip04_mac_interrupt(int irq, void *dev_id)
>> +{
>> + struct net_device *ndev = (struct net_device *)dev_id;
>
> Unnecessary cast of void *
>
> []
>
>> +static int hip04_set_coalesce(struct net_device *netdev,
>> + struct ethtool_coalesce *ec)
>> +{
>> + struct hip04_priv *priv = netdev_priv(netdev);
>> +
>> + /* Check not supported parameters */
>> + if ((ec->rx_max_coalesced_frames) || (ec->rx_coalesce_usecs_irq) ||
>> + (ec->rx_max_coalesced_frames_irq) || (ec->tx_coalesce_usecs_irq) ||
>> + (ec->use_adaptive_rx_coalesce) || (ec->use_adaptive_tx_coalesce) ||
>> + (ec->pkt_rate_low) || (ec->rx_coalesce_usecs_low) ||
>> + (ec->rx_max_coalesced_frames_low) || (ec->tx_coalesce_usecs_high) ||
>> + (ec->tx_max_coalesced_frames_low) || (ec->pkt_rate_high) ||
>> + (ec->tx_coalesce_usecs_low) || (ec->rx_coalesce_usecs_high) ||
>> + (ec->rx_max_coalesced_frames_high) || (ec->rx_coalesce_usecs) ||
>> + (ec->tx_max_coalesced_frames_irq) ||
>> + (ec->stats_block_coalesce_usecs) ||
>> + (ec->tx_max_coalesced_frames_high) || (ec->rate_sample_interval))
>> + return -EOPNOTSUPP;
>
> Rather than a somewhat haphazard mix of these values,
> this might be simpler to read as something like:
>
> /* Check not supported parameters */
> if (ec->pkt_rate_low ||
> ec->pkt_rate_high ||
>
> ec->use_adaptive_rx_coalesce ||
> ec->rx_coalesce_usecs ||
> ec->rx_coalesce_usecs_low ||
> ec->rx_coalesce_usecs_high ||
> ec->rx_coalesce_usecs_irq ||
> ec->rx_max_coalesced_frames ||
> ec->rx_max_coalesced_frames_low ||
> ec->rx_max_coalesced_frames_high ||
> ec->rx_max_coalesced_frames_irq ||
>
> ec->use_adaptive_tx_coalesce ||
> ec->tx_coalesce_usecs_low ||
> ec->tx_coalesce_usecs_high ||
> ec->tx_max_coalesced_frames_low ||
> ec->tx_max_coalesced_frames_high ||
> ec->tx_max_coalesced_frames_irq ||
>
> ec->stats_block_coalesce_usecs ||
> ec->rate_sample_interval)
> return -EOPNOTSUPP;
>
>
>> +static void hip04_free_ring(struct net_device *ndev, struct device *d)
>> +{
>> + struct hip04_priv *priv = netdev_priv(ndev);
>> + int i;
>> +
>> + for (i = 0; i < RX_DESC_NUM; i++)
>> + if (priv->rx_buf[i])
>> + put_page(virt_to_head_page(priv->rx_buf[i]));
>
> It's generally nicer to use braces around
> for loops with single ifs.
>
>> +
>> + for (i = 0; i < TX_DESC_NUM; i++)
>> + if (priv->tx_skb[i])
>> + dev_kfree_skb_any(priv->tx_skb[i]);
>
>
>
OK, fix them later, thanks.
Ding
> .
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
