> On Mar 6, 2015, at 11:08 PM, Nicolas Ferre <[email protected]> wrote:
>
> Le 26/02/2015 10:34, Jean-Christophe PLAGNIOL-VILLARD a écrit :
>> Today if we want to disable a pio bank we may will siliently break pinctrl
>> configuration in the DT. This will be detected only at runtime.
>>
>> So move the pinctrl configuration to the bank instead of the bus.
>> This allow to detect pinctrl issue at DT compiling time when disable a bank.
>>
>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <[email protected]>
>> Cc: Linus Walleij <[email protected]>
>> Cc: [email protected]
>> ---
>> .../bindings/pinctrl/atmel,at91-pinctrl.txt | 66
>> ++++++++++++++++++++++
>> 1 file changed, 66 insertions(+)
>>
>> diff --git
>> a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
>> b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
>> index b7a93e8..78355ee 100644
>> --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
>> +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
>> @@ -148,3 +148,69 @@ dbgu: serial@fffff200 {
>> pinctrl-0 = <&pinctrl_dbgu>;
>> status = "disabled";
>> };
>> +
>> +II) New Bindings per PIO Block
>
> Sorry but NACK.
>
> I don't want to manage another flavor of the pinmux biding with no real
> benefit. I would have been good if we had it from day-1. Now it's too late.
yes we do, we catch but a compiling time instead of RUNTIME which is critical
so I’ll pass on the NACK
>
> Moreover, splitting a binding definition if you have a function given by
> multiple banks can be weird and not well understood in regard to our
> current group+function definition scheme (Cf. your last example).
>
Others already do so and this is not complex at all
Best Regards,
J.
>
>> +This allow to detect pinctrl issue at DT compiling time when disable a bank
>> +
>> +Required properties for iomux controller:
>> +- compatible: "atmel,at91rm9200-pio-pinctrl" or
>> "atmel,at91sam9x5-pio-pinctrl"
>> + or "atmel,sama5d3-pio-pinctrl"
>> +- atmel,mux-mask: array of mask (periph per bank) to describe if a pin can
>> be
>> + configured in this periph mode. All the periph and bank need to be
>> describe.
>> +
>> +How to create such array:
>> +
>> +Each column will represent the possible peripheral of the pinctrl for the
>> bank
>> +
>> +Take an example on the 9260
>> +Peripheral: 2 ( A and B)
>> +=>
>> +
>> + /* A B */
>> + 0xffffffff 0xffc00c3b /* pioA */
>> +
>> +For each peripheral/bank we will descibe in a u32 if a pin can be
>> +configured in it by putting 1 to the pin bit (1 << pin)
>> +
>> +Required properties for pin configuration node:
>> +- atmel,pins: 3 integers array, represents a group of pins mux and config
>> + setting. The format is atmel,pins = <PIN_NUM PERIPH CONFIG>.
>> + The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B...
>> +
>> +Bits used for CONFIG:
>> +cf atmel,at91-pinctrl
>> +
>> +pioB: gpio@fffff600 {
>> + compatible = "atmel,at91rm9200-gpio", "atmel,at91rm9200-pio-pinctrl";
>> + reg = <0xfffff600 0x200>;
>> + interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
>> + #gpio-cells = <2>;
>> + gpio-controller;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> + clocks = <&pioB_clk>;
>> +
>> + /* A B */
>> + atmel,mux-mask = <0xffffffff 0x7fff3ccf>;
>> +
>> + dbgu {
>> + pinctrl_dbgu: dbgu-0 {
>> + atmel,pins =
>> + <14 0x1 0x0 /* PB14 periph A */
>> + 15 0x1 0x1>; /* PB15 periph A with pullup */
>> + };
>> + };
>> +};
>> +
>> +dbgu: serial@fffff200 {
>> + compatible = "atmel,at91sam9260-usart";
>> + reg = <0xfffff200 0x200>;
>> + interrupts = <1 4 7>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_dbgu>;
>> + status = "disabled";
>> +};
>> +
>> +if you have to use multiple bank
>> + pinctrl-0 = <&pinctrl_ip_piaa>, <&pinctrl_ip_piab>;
>>
>
> Best regards,
> --
> Nicolas Ferre
>
> _______________________________________________
> linux-arm-kernel mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
