Broadcom's Cygnus chip has a USB 2.0 host controller connected to three separate phys. One of the phs (port 2) is also connectd to a usb 2.0 device controller
Signed-off-by: Arun Ramamurthy <[email protected]> Reviewed-by: Ray Jui <[email protected]> Reviewed-by: Scott Branden <[email protected]> --- .../bindings/phy/brcm,cygnus-usb-phy.txt | 69 ++++++++++++++++++++++ 1 file changed, 69 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt diff --git a/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt b/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt new file mode 100644 index 0000000..d1a9a65 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,cygnus-usb-phy.txt @@ -0,0 +1,69 @@ +BROADCOM CYGNUS USB PHY + +Required Properties: + - compatible: brcm,cygnus-usb-phy + - reg : usbphy_regs - Base address of phy registers + usb2h_idm_regs - Base address of host idm registers + usb2d_idm_regs - Base address of device idm registers + - phy-cells - must be 1 for each port declared. This is because the node + that uses the phy must provide one integers, 0 for device + and 1 for host + +NOTE: port 0 and port 1 are host only and port 2 can be configured for host or +device. + +Example of phy : + usbphy0: usbphy@0x0301c000 { + compatible = "brcm,cygnus-usb-phy"; + reg = <0x0301c000 0x2000>, + <0x18115000 0x1000>, + <0x18111000 0x1000>; + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + usbphy0_0: usbphy0@0 { + #phy-cells = <1>; + reg = <0>; + status = "okay"; + phy-supply = <&vbus_p0>; + }; + + usbphy0_1: usbphy0@1 { + #phy-cells = <1>; + reg = <1>; + status = "okay"; + }; + + usbphy0_2: usbphy0@2 { + #phy-cells = <1>; + reg = <2>; + status = "okay"; + phy-supply = <&vbus_p2>; + }; + }; + +Example of node using the phy: + + /* This nodes declares all three ports as host */ + + ehci0: usb@0x18048000 { + compatible = "generic-ehci"; + reg = <0x18048000 0x100>; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbphy0_0 1 &usbphy0_1 1 &usbphy0_2 1>; + status = "okay"; + }; + + /* + * This node declares port 2 phy + * and configures it for device + */ + + usbd_udc_dwc1: usbd_udc_dwc@0x1804c000 { + compatible = "iproc-udc"; + reg = <0x1804c000 0x2000>; + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbphy0_2 0>; + phy-names = "usb"; + }; -- 2.3.4 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
