Hi, On Monday 14 December 2015 21:26:25 Laurent Pinchart wrote: > Hi Markus, > > Thank you for the patch. > > On Monday 14 December 2015 15:41:51 Markus Pargmann wrote: > > Add optional reset and standby gpios. The reset gpio is used to reset > > the chip in power_on(). > > > > The standby gpio is not used currently. It is just unset, so the chip is > > not in standby. > > > > Signed-off-by: Markus Pargmann <[email protected]> > > Reviewed-by: Philipp Zabel <[email protected]> > > Acked-by: Rob Herring <[email protected]> > > --- > > .../devicetree/bindings/media/i2c/mt9v032.txt | 2 ++ > > drivers/media/i2c/mt9v032.c | 28 +++++++++++++++++++ > > 2 files changed, 30 insertions(+) > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt > > b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt index > > 202565313e82..100f0ae43269 100644 > > --- a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt > > +++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt > > @@ -20,6 +20,8 @@ Optional Properties: > > > > - link-frequencies: List of allowed link frequencies in Hz. Each frequency > > is expressed as a 64-bit big-endian integer. > > +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. > > +- standby-gpios: GPIO handle which is connected to the standby pin of the > > chip. > > > > For further reading on port node refer to > > Documentation/devicetree/bindings/media/video-interfaces.txt. > > diff --git a/drivers/media/i2c/mt9v032.c b/drivers/media/i2c/mt9v032.c > > index a68ce94ee097..c1bc564a0979 100644 > > --- a/drivers/media/i2c/mt9v032.c > > +++ b/drivers/media/i2c/mt9v032.c > > @@ -14,6 +14,7 @@ > > > > #include <linux/clk.h> > > #include <linux/delay.h> > > +#include <linux/gpio/consumer.h> > > #include <linux/i2c.h> > > #include <linux/log2.h> > > #include <linux/mutex.h> > > @@ -251,6 +252,8 @@ struct mt9v032 { > > > > struct regmap *regmap; > > struct clk *clk; > > + struct gpio_desc *reset_gpio; > > + struct gpio_desc *standby_gpio; > > > > struct mt9v032_platform_data *pdata; > > const struct mt9v032_model_info *model; > > @@ -312,16 +315,31 @@ static int mt9v032_power_on(struct mt9v032 *mt9v032) > > struct regmap *map = mt9v032->regmap; > > int ret; > > > > + if (mt9v032->reset_gpio) > > + gpiod_set_value_cansleep(mt9v032->reset_gpio, 1); > > + > > gpiod_set_value_cansleep() already checks whether the gpiod is NULL, you > don't > need to duplicate the check here. > > Apart from that, > > Acked-by: Laurent Pinchart <[email protected]> > > No need to resubmit I'll fix this when applying.
Ok, thank you.
Best Regards,
Markus
>
> > ret = clk_set_rate(mt9v032->clk, mt9v032->sysclk);
> > if (ret < 0)
> > return ret;
> >
> > + /* System clock has to be enabled before releasing the reset */
> > ret = clk_prepare_enable(mt9v032->clk);
> > if (ret)
> > return ret;
> >
> > udelay(1);
> >
> > + if (mt9v032->reset_gpio) {
> > + gpiod_set_value_cansleep(mt9v032->reset_gpio, 0);
> > +
> > + /* After releasing reset we need to wait 10 clock cycles
> > + * before accessing the sensor over I2C. As the minimum SYSCLK
> > + * frequency is 13MHz, waiting 1µs will be enough in the worst
> > + * case.
> > + */
> > + udelay(1);
> > + }
> > +
> > /* Reset the chip and stop data read out */
> > ret = regmap_write(map, MT9V032_RESET, 1);
> > if (ret < 0)
> > @@ -954,6 +972,16 @@ static int mt9v032_probe(struct i2c_client *client,
> > if (IS_ERR(mt9v032->clk))
> > return PTR_ERR(mt9v032->clk);
> >
> > + mt9v032->reset_gpio = devm_gpiod_get_optional(&client->dev, "reset",
> > + GPIOD_OUT_HIGH);
> > + if (IS_ERR(mt9v032->reset_gpio))
> > + return PTR_ERR(mt9v032->reset_gpio);
> > +
> > + mt9v032->standby_gpio = devm_gpiod_get_optional(&client->dev, "standby",
> > + GPIOD_OUT_LOW);
> > + if (IS_ERR(mt9v032->standby_gpio))
> > + return PTR_ERR(mt9v032->standby_gpio);
> > +
> > mutex_init(&mt9v032->power_lock);
> > mt9v032->pdata = pdata;
> > mt9v032->model = (const void *)did->driver_data;
>
>
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
signature.asc
Description: This is a digitally signed message part.
