Thank you Marcus again,
I changed device address, in both places, but the same problem appears. I
see that it loads now 4rx image, but the problem remains.
self.uhd_usrp_source_1 = uhd.usrp_source(
device_addr="fpga=usrp1_fpga_4rx.rbf",
stream_args=uhd.stream_args(
cpu_format="fc32",
channels=range(1),
),
)
On Tue, Dec 3, 2013 at 5:40 PM, Marcus D. Leech <[email protected]> wrote:
> On 12/03/2013 11:24 AM, Nemanja Savic wrote:
>
> I see, but still don't get where this change should be made.
> And also, more important, i I have standard configuration with 2 DDCs and
> 2 DUCs, then it should work like that, cause I need only 2 DDCs if I am not
> wrong.
>
> YOu make the change in the device_addr args.
>
> And you really do need the 4RX image to make this work.
>
>
>
>
> On Tue, Dec 3, 2013 at 5:15 PM, Marcus D. Leech <[email protected]> wrote:
>
>> On 12/03/2013 11:10 AM, Nemanja Savic wrote:
>>
>> Hi all guys,
>>
>> I would like to receive in my application signals from WBX board and
>> from LFTX simultaneousely.
>> At the moment, when I run the flow graph it ends immediately with core
>> dump, and zero divisin exception.
>>
>> In the script, sources are defined in this way:
>>
>> self.uhd_usrp_source_0 = uhd.usrp_source(
>> device_addr="",
>> stream_args=uhd.stream_args(
>> cpu_format="fc32",
>> channels=range(1),
>> ),
>> )
>>
>> self.uhd_usrp_source_0.set_subdev_spec("A:0", 0)
>> self.uhd_usrp_source_0.set_samp_rate(samp_rate_wbx)
>> self.uhd_usrp_source_0.set_center_freq(433900000, 0)
>> self.uhd_usrp_source_0.set_gain(input_gain_slider_wbx, 0)
>> self.uhd_usrp_source_0.set_antenna("RX2", 0)
>>
>> and the second:
>>
>> self.uhd_usrp_source_1 = uhd.usrp_source(
>> device_addr="",
>> stream_args=uhd.stream_args(
>> cpu_format="fc32",
>> channels=range(1),
>> ),
>> )
>>
>> self.uhd_usrp_source_1.set_subdev_spec("B:A", 0)
>> self.uhd_usrp_source_1.set_samp_rate(samp_rate_CC1000)
>> self.uhd_usrp_source_1.set_center_freq(freq_CC1000, 0)
>> self.uhd_usrp_source_1.set_gain(gain_CC1000, 0)
>>
>> There are certain posts about using different firmware, but I am not
>> able to figure out what should I really do, and is that necessary?
>>
>> Thanx for help,
>>
>> Best,
>>
>> --
>> Nemanja Savić
>>
>>
>> _______________________________________________
>> Discuss-gnuradio mailing
>> [email protected]https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>
>> You need to specify the dual-DDC image for USRP1:
>>
>> usrp1_fpga_4rx.rbf
>>
>>
>> http://files.ettus.com/uhd_docs/manual/html/usrp1.html#specify-a-non-standard-image
>>
>>
>>
>> --
>> Marcus Leech
>> Principal Investigator
>> Shirleys Bay Radio Astronomy Consortiumhttp://www.sbrac.org
>>
>>
>> _______________________________________________
>> Discuss-gnuradio mailing list
>> [email protected]
>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>
>>
>
>
> --
> Nemanja Savić
>
>
>
> --
> Marcus Leech
> Principal Investigator
> Shirleys Bay Radio Astronomy Consortiumhttp://www.sbrac.org
>
>
--
Nemanja Savić
_______________________________________________
Discuss-gnuradio mailing list
[email protected]
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
