From: xianda [mailto:[email protected]] Sent: 05 June 2014 09:50 To: David Halls Subject: Re:Re: [Discuss-gnuradio] Scheduling a block even with no input items RE: Flow graph blocking when doing 2x1 transmission
Hi David:
Thank you in advance.
I want to ask a question about "Payload TD Tx 1 is derived from
input codewords that are generated in MATLAB and stored in a file, then loaded
into the flow graph." as you said.I want to ask how to gnerated a dat document
which is in MATLAB.What command you use in MATLAB?
Thanks very much.
Best regards,
xianda
Hi Xianda,
Please find the zip file attached with files to read and write (to/from MATLAB)
both complex, and byte types.
Syntax is
input = read_complex_binary('filename.dat')
input = read_char_binary('filename.dat')
write_complex_binary(data,'filename.dat')
write_char_binary(data,'filename.dat')
Regards,
David
At 2014-06-04 08:53:31, "David Halls"
<[email protected]<mailto:[email protected]>> wrote:
Hi Activecat,
I have disconnected the rest of the flow graph because it is extremely complex.
In the system I have a Source, a Relay (1 rx USRP, 1 tx USRP), a Destination. S
---> R_rx/R_tx --> D
The two transmitters that you see on that flow graph snippet I sent you are the
the Source Tx and the Relay Tx.
Payload TD Tx 1 is derived from input codewords that are generated in MATLAB
and stored in a file, then loaded into the flow graph. The payload is created
in a similar fashion to Martin's original OFDM_tx. This is then transmitted
from Source Tx.
Until this point, no packets are received by Relay Rx but once the source
transmits, these packets are then received by Relay Rx, and then there is a
decode-and-forward chain of blocks, and this then creates Payload TD Tx 2.
The full flow graph is attached, but may be missing many blocks for you...
David
________________________________________
From: Activecat [[email protected]<mailto:[email protected]>]
Sent: 04 June 2014 13:45
To: [email protected]<mailto:[email protected]>
Cc: David Halls
Subject: Re: [Discuss-gnuradio] Scheduling a block even with no input items RE:
Flow graph blocking when doing 2x1 transmission
On Wed, Jun 4, 2014 at 7:10 PM, David Halls
<[email protected]<mailto:[email protected]><mailto:[email protected]<mailto:[email protected]>>>
wrote:
Activecat,
In fact my horrible hack doesn't work properly. Once items start arriving at
Payload TD Tx 2, they still don't arrive as 'consistently' (for want of a
better word), as those from the Noise Source block, and thus zeros are inserted
when they are not required!
David
David,
Could you please explain in details, what is this Payload TD Tx 2?
How does it generate data, is it getting data from a hardware or console, why
it sometime idle but sometime transmitting?
This is a virtual source. Where is it associated virtual sink?
________________________________
NOTE: The information in this email and any attachments may be confidential
and/or legally privileged. This message may be read, copied and used only by
the intended recipient. If you are not the intended recipient, please destroy
this message, delete any copies held on your system and notify the sender
immediately.
Toshiba Research Europe Limited, registered in England and Wales (2519556).
Registered Office 208 Cambridge Science Park, Milton Road, Cambridge CB4 0GZ,
England. Web: www.toshiba.eu/research/trl<http://www.toshiba.eu/research/trl>
________________________________
This email has been scanned for email related threats and delivered safely by
Mimecast.
For more information please visit http://www.mimecast.com
________________________________
________________________________
NOTE: The information in this email and any attachments may be confidential
and/or legally privileged. This message may be read, copied and used only by
the intended recipient. If you are not the intended recipient, please destroy
this message, delete any copies held on your system and notify the sender
immediately.
Toshiba Research Europe Limited, registered in England and Wales (2519556).
Registered Office 208 Cambridge Science Park, Milton Road, Cambridge CB4 0GZ,
England. Web: www.toshiba.eu/research/trl
---------------------------------------------------------------------------------------
This email has been scanned for email related threats and delivered safely by
Mimecast.
For more information please visit http://www.mimecast.com
---------------------------------------------------------------------------------------
Read_Write.rar
Description: Read_Write.rar
_______________________________________________ Discuss-gnuradio mailing list [email protected] https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
