Yes and no. The signal source just uses the information "sampling rate" to
calculate the length of one period in samples. Other than that, nothing in GNU
radio cares about sampling rate - that's a real world concept that only applies
to real world devices (such as the USRP sink) but not to the digital signal
processing. You should make sure to use the same nominal sampling rate that you
used to generate the files with the signal in. For example, if you calculated
the satellite signal based on a nominal rate of 1MS/s, and play it back at
5MS/s, everything will be frequency scaled with a factor of five.
Greetings,
Marcus
On December 22, 2014 11:51:34 AM CET, Carlos Alberto Ruiz Naranjo
<[email protected]> wrote:
>Ok. Signal and sine must have the same sample rate (5 MS/s), right?
>
>2014-12-22 11:46 GMT+01:00 Marcus Müller <[email protected]>:
>
>> Yes and no: the shifting is done right; however, you should make
>sure to
>> use a consistent sampling rate throughout the block.
>> The USRP sink interprets the samples that come into it as having a
>sample
>> rate of 5MS/s, whereas the nominal sampling rate in the signal
>sources is
>> set to 2MS/s.
>>
>>
>>
>> On 12/22/2014 10:45 AM, Saul E. wrote:
>>
>> First of all, I want to thank you for your answer.
>>
>> Then, It is correct? (for a simple simulation of 1k, 2k and 3k Hz of
>> doppler shift)
>>
>>
>>
>>
>>
>> Thank you.
>>
>> Saul E.
>>
>>
>>
>> 2014-12-22 10:26 GMT+01:00 Marcus Müller <[email protected]>:
>>
>>> Hi Saul,
>>>
>>> a doppler shift is, mathematically speaking, nothing more than a
>>> multiplication with a complex sine, so use a multiply block and a
>signal
>>> source per simulated sattelite.
>>>
>>> Now, you might want to update your doppler shift according to a
>simulated
>>> sattelite's position. I recommend having a look at PyEphem[1], which
>offers
>>> you calculational routines for such things, and writing your own
>python
>>> block[2] to generate the complex sine.
>>>
>>> Greetings,
>>> Marcus
>>>
>>> [1] http://rhodesmill.org/pyephem/
>>> [2]
>http://gnuradio.org/redmine/projects/gnuradio/wiki/Guided_Tutorials
>>> ; go through tutorials 1, 2, 3
>>>
>>>
>>> On 12/22/2014 10:14 AM, Saul E. wrote:
>>>
>>> Hi all!!
>>>
>>> I am developing a SDR receiver and want to simulate the doppler of
>signal
>>> from several satellites.
>>> Any suggestions?
>>>
>>> Signal1, signal2 and signal3 are BPSK signals and I use a USRP
>N200.
>>>
>>>
>>>
>>>
>>>
>>> Thank you very much in advance.
>>> Saul E.
>>>
>>>
>>>
>>> _______________________________________________
>>> Discuss-gnuradio mailing
>[email protected]https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>>
>>>
>>>
>>> _______________________________________________
>>> Discuss-gnuradio mailing list
>>> [email protected]
>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>>
>>>
>>
>>
>> _______________________________________________
>> Discuss-gnuradio mailing list
>> [email protected]
>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>
>>
--
Sent from my Android device with K-9 Mail. Please excuse my brevity.
_______________________________________________
Discuss-gnuradio mailing list
[email protected]
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
