Hi Organ,
This all sounds like you still have the horribly outdated version of UHD
installed that Ubuntu 14.04 has. Make sure to
sudo apt-get remove uhd libuhd\* uhd-host
And run build-gnuradio again.
Best regards,
Marcus
Am 27. November 2015 04:36:17 MEZ, schrieb "Orhan Öçal" <[email protected]>:
>Hello,
>
>I have been trying to have GNURADIO and USRP B200 work on a Ubuntu
>14.04.3
>
>I have first tried the call `sudo apt-get install gnuradio`. This
>installs
>GNURADIO fine. However, the drivers for B200 is not installed
>unfortunately, hence the machine cannot see my device.
>
>So instead I downloaded the driver binaries after updating the apt-get
>package manager through the way written on ETTUS research's website
>http://files.ettus.com/manual/page_install.html#install_linux_pkgmgr
>This
>solved the problem with connecting to USRP B200. However, it
>uninstalled
>gnuradio as expected since it depends on the UHD library. Then I
>installed
>gnuradio by `apt-get install gnuradio`. However, this gives a
>segmentation
>fault when I try running gnuradio. This link
>https://www.ruby-forum.com/topic/4837808 mentions about such a problem
>due
>to `libboost`, I believe I have the same problem.
>
>So instead I tried building GNURADIO and UHD through the installation
>script as `wget http://www.sbrac.org/files/build-gnuradio && chmod a+x
>./build-gnuradio && ./build-gnuradio`. However, with this I get the
>following error:
>
>##############################
>
>[ 87%] Building CXX object
>gr-uhd/swig/CMakeFiles/_uhd_swig.dir/uhd_swigPYTHON_wrap.cxx.o
>/home/username/Documents/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:
>In function ‘void init_uhd_swig()’:
>/home/username/Documents/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:47037:91:
>error: ‘ATR_REG_IDLE’ is not a member of ‘uhd::usrp::dboard_iface’
> SWIG_Python_SetConstant(d,
>"dboard_iface_ATR_REG_IDLE",SWIG_From_int(static_cast< int
>>(uhd::usrp::dboard_iface::ATR_REG_IDLE)));
>
> ^
>/home/username/Documents/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:47038:94:
>error: ‘ATR_REG_TX_ONLY’ is not a member of ‘uhd::usrp::dboard_iface’
> SWIG_Python_SetConstant(d,
>"dboard_iface_ATR_REG_TX_ONLY",SWIG_From_int(static_cast< int
>>(uhd::usrp::dboard_iface::ATR_REG_TX_ONLY)));
>
> ^
>/home/username/Documents/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:47039:94:
>error: ‘ATR_REG_RX_ONLY’ is not a member of ‘uhd::usrp::dboard_iface’
> SWIG_Python_SetConstant(d,
>"dboard_iface_ATR_REG_RX_ONLY",SWIG_From_int(static_cast< int
>>(uhd::usrp::dboard_iface::ATR_REG_RX_ONLY)));
>
> ^
>/home/username/Documents/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:47040:98:
>error: ‘ATR_REG_FULL_DUPLEX’ is not a member of
>‘uhd::usrp::dboard_iface’
> SWIG_Python_SetConstant(d,
>"dboard_iface_ATR_REG_FULL_DUPLEX",SWIG_From_int(static_cast< int
>>(uhd::usrp::dboard_iface::ATR_REG_FULL_DUPLEX)));
>
> ^
>make[2]: ***
>[gr-uhd/swig/CMakeFiles/_uhd_swig.dir/uhd_swigPYTHON_wrap.cxx.o] Error
>1
>make[1]: *** [gr-uhd/swig/CMakeFiles/_uhd_swig.dir/all] Error 2
>make: *** [all] Error 2
>make failed
>Exiting Gnu Radio build/install
>
>##############################
>
>The script builds UHD itself, I could not think of how to approach
>this
>problem. Would you have any hints as to how to proceed?
>
>Oh, and, happy thanksgiving!
>
>Orhan
>
>
>------------------------------------------------------------------------
>
>_______________________________________________
>Discuss-gnuradio mailing list
>[email protected]
>https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
--
Sent from my Android device with K-9 Mail. Please excuse my brevity.
_______________________________________________
Discuss-gnuradio mailing list
[email protected]
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
