Hi All
I am Srinivasan living in Singapore and have M.Sc. Comp.Sci.
My self and few engineers have detected unknown RF at 2.4 GHz which has
different FFT pattern, waterfall image, Radio Sound.
The identification and classification of the signal is really difficult
process.
Below is the video reference :
· FFT at 2.4 GHz ( we can see sudden fluctuation and power in db is
really high )
https://sendvid.com/33f5hpkg
Detail : On this video, we can see peak hold in green color that leave a
trace something comes and go. Peak Hold line in green color shows external
signal interfered at 2.4 GHz
The fluctuation looks like external RF writing to it.
· Spectrum Density of RF at 2.4 GHz
http://sendvid.com/mu9m2jeg
Details : I have taken this video at place where there was no devices
that operate at 2.4 GHz ( near plantations ).
We can see noise floor in blue color comes and go.
This external interference cause Wi-Fi at 2.4 GHz to fluctuate and
sudden fluctuate at different power level will increase of SNR of Wi-Fi (
signal to noise ratio )
· AirMagnet XT
https://sendvid.com/tkq3xz0s
Details : This software one of the best software available in the market
for detection interference Wi-Fi at 2.4 GHz with different options.
We can see FFT picture at real time in leave suddenly max hold
around -10 dBm.
· Wi-Fi Fluctuations at Siloam Hospital in Medan - Indonesia
http://sendvid.com/2u2j34m7
I reported this issue to :
1. iDA - Singapore ( Radio Spectrum monitor - Goverment agency )
2. MCMC - Singapore ( Radio Spectrum monitor - Goverment agency )
3. Balmon - Indonesia ( Radio Spectrum monitor - Goverment agency )
4. Flight Operator because this unknown signal works on the flight as well.
They are not sure on how to pin point the source and other mechanism.
This signal works in 3 countries : Indonesia, Malaysia and Singapore.
The source may come from Satellite and possibility from SES-7 because this
satellite has S-band transponder.
Based on my detection :
1. The RF covered by Wi-Fi signal. This can be seen while recording the
signal in wav format using SDR# and HackRF
Image below :
cid:[email protected]
2. The carrier frequency is 2.4 GHz
3. Density value which I recorded :
1. 0.4187 mW / m2 ( 418.7 µW / m2 )
2. 0.5520 mW / m2 ( 552.0 µW / m2 )
3. 15.92 mW / m2 ( 15920 µW / m2 )
4. Recently i detected 1827 mW / m2 = 1.827 W / m2 = 1827000 uW / m2
Attached Radio Sound file :
https://mega.nz/#!8thAzY5D!4ZfOmHLSttQKtYQQlz6BBVtV_vqjrVsxSRiJVzdnRqs
Attached technical analysis in 84 pages ;
<https://mega.nz/#!YwplVCCT!Acbe00paHk3dLJuf04B5zSBifSw0-bHz5IciiNLgQwY>
https://mega.nz/#!YwplVCCT!Acbe00paHk3dLJuf04B5zSBifSw0-bHz5IciiNLgQwY
I know that Radio Sound that can be analyst further.
I am looking for external expert - urgently to help on this. Looking forward
for your reply.
Regards
Srinivasan T
HP : 65 - 91236851
_______________________________________________
Discuss-gnuradio mailing list
[email protected]
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
