Hi Marcus,
No luck, I removed complete folder and uninstalled all previous installations by $ sudo apt-get purge --auto-remove uhd-host and installed uhd & gnuradio from source. uhd completed successfully, but gnuradio showing same errors. How to resolve it ? -ben ________________________________ From: Marcus Müller <marcus.muel...@ettus.com> Sent: Sunday, October 30, 2016 8:41:44 PM To: Benny Alexandar; discuss-gnuradio@gnu.org Subject: Re: [Discuss-gnuradio] Not able to build GNU Radio (git checkout v3.7.10.1) So, you want to make sure you *don't* install uhd-host via apt-get, then do the UHD source build and installation, and then do the GNU Radio source build and installation. Best regards, Marcus On 10/30/2016 04:07 PM, Benny Alexandar wrote: Hi Marcus, I installed uhd from source and is ( git checkout release_003_010_000_000), from this link https://kb.ettus.com/Building_and_Installing_the_USRP_Open-Source_Toolchain_(UHD_and_GNU_Radio)_on_Linux<https://kb.ettus.com/Building_and_Installing_the_USRP_Open-Source_Toolchain_%28UHD_and_GNU_Radio%29_on_Linux> Can i uninstall uhd completely, by the below command sudo apt-get purge --auto-remove uhd-host Again, fresh installation should I first install uhd followed by gnuradio ? -ben ________________________________ From: Marcus Müller <marcus.muel...@ettus.com><mailto:marcus.muel...@ettus.com> Sent: Sunday, October 30, 2016 8:01:19 PM To: Benny Alexandar; discuss-gnuradio@gnu.org<mailto:discuss-gnuradio@gnu.org> Subject: Re: [Discuss-gnuradio] Not able to build GNU Radio (git checkout v3.7.10.1) Hi Ben, This is very symptomatic of a system with conflicting installs of a library, in your case UHD. Uninstall all UHDs that you have (check by searching for libuhd.so<http://libuhd.so> and multi_usrp.* globally) and reinstall only that UHD you want. If that is not the UHD that came with your Linux distro, make sure you don't accidentally reinstall it, e.g. by installing something that depends on it. Best regards, Marcus Am 30. Oktober 2016 15:22:22 MEZ, schrieb Benny Alexandar <ben.a...@outlook.com><mailto:ben.a...@outlook.com>: Hi, I get this following error while building GNU Radio 3.7.10.1. Please find the below errors ----- [ 86%] Built target uhd_swig_gr_uhd_swig_5e3ce Scanning dependencies of target _uhd_swig [ 86%] Building CXX object gr-uhd/swig/CMakeFiles/_uhd_swig.dir/uhd_swigPYTHON_wrap.cxx.o /home/ben/workarea-gnuradio/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx: In function ‘PyObject* _wrap_dboard_iface_set_gpio_debug(PyObject*, PyObject*, PyObject*)’: /home/ben/workarea-gnuradio/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:26696:15: error: ‘class uhd::usrp::dboard_iface’ has no member named ‘set_gpio_debug’ (arg1)->set_gpio_debug(arg2,arg3); ^ /home/ben/workarea-gnuradio/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx: In function ‘PyObject* _wrap_dboard_iface_sptr_set_gpio_debug(PyObject*, PyObject*, PyObject*)’: /home/ben/workarea-gnuradio/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:27979:16: error: ‘class uhd::usrp::dboard_iface’ has no member named ‘set_gpio_debug’ (*arg1)->set_gpio_debug(arg2,arg3); ^ /home/ben/workarea-gnuradio/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx: In function ‘void init_uhd_swig()’: /home/ben/workarea-gnuradio/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:48039:91: error: ‘ATR_REG_IDLE’ is not a member of ‘uhd::usrp::dboard_iface’ SWIG_Python_SetConstant(d, "dboard_iface_ATR_REG_IDLE",SWIG_From_int(static_cast< int >(uhd::usrp::dboard_iface::ATR_REG_IDLE))); ^ /home/ben/workarea-gnuradio/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:48040:94: error: ‘ATR_REG_TX_ONLY’ is not a member of ‘uhd::usrp::dboard_iface’ SWIG_Python_SetConstant(d, "dboard_iface_ATR_REG_TX_ONLY",SWIG_From_int(static_cast< int >(uhd::usrp::dboard_iface::ATR_REG_TX_ONLY))); ^ /home/ben/workarea-gnuradio/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:48041:94: error: ‘ATR_REG_RX_ONLY’ is not a member of ‘uhd::usrp::dboard_iface’ SWIG_Python_SetConstant(d, "dboard_iface_ATR_REG_RX_ONLY",SWIG_From_int(static_cast< int >(uhd::usrp::dboard_iface::ATR_REG_RX_ONLY))); ^ /home/ben/workarea-gnuradio/gnuradio/build/gr-uhd/swig/uhd_swigPYTHON_wrap.cxx:48042:98: error: ‘ATR_REG_FULL_DUPLEX’ is not a member of ‘uhd::usrp::dboard_iface’ SWIG_Python_SetConstant(d, "dboard_iface_ATR_REG_FULL_DUPLEX",SWIG_From_int(static_cast< int >(uhd::usrp::dboard_iface::ATR_REG_FULL_DUPLEX))); ^ make[2]: *** [gr-uhd/swig/CMakeFiles/_uhd_swig.dir/uhd_swigPYTHON_wrap.cxx.o] Error 1 make[1]: *** [gr-uhd/swig/CMakeFiles/_uhd_swig.dir/all] Error 2 make: *** [all] Error 2 ________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org<mailto:Discuss-gnuradio@gnu.org> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio -- Sent from my Android device with K-9 Mail. Please excuse my brevity.
_______________________________________________ Discuss-gnuradio mailing list Discuss-gnuradio@gnu.org https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
