I have two Squeezebox v3 (~18 months old). Until last Sunday I was using the Slimserver v6.2.1 and everything was fine. I've then decided to install the Softsqueeze 3.3 which made me upgrade to the slimserver to v6.5.2.(or at least I thought I did but I ended up apparently with 6.5.1)
Since then one of the Squeezebox keeps hanging then resetting as soon as a play a file (FLAC) (i.e. anywhere between 2secs and 2 minutes into playing the song) from the slimserver or from Internet radios. Navigating through the menus doesn't cause the reset. Sometimes when the box hangs the display flashes or displays garbage or display lines (noise) in every direction then turns blank the the box resets. The sound turns sometimes into noise too. I've changed the power supply (using the other one) but it still hangs then resets. I have the impression that the box resets because I see the Squeezebox logo when it comes back up. Also sometimes it comes back up instantly, sometimes it can take 1 or 2 minutes or so. The remote at that time isn't responsive so I can't turn it back on with it. But if I unplug the power cable (after it has hang) and plug it back on it boots instantly. The other Squeezebox runs as good as before. I didn't changed any of the hardware configuration when these problems started to appear but just as a test I've swapped both squeezebox. The faulty one keeps faulting even at the new "location". Here is some information on my setup: Faulty Squeezebox v3: - Connected through wireless to a linksys router (this always worked before the slimserver upgrade). No hardware changes were made. Signal Strength:~70% - Gets IP address through DHCP - Slimserver appears to be v6.5.1 (although I've installed a 6.5.2 archive)running on Windows XP SP2 - Firmware version: 72 - Mac address: 00 04 20 06 3D CF - Connected through the analog outputs to a Harman/Kardon AVR340 and also tried to a Harman/Kardon AVR7300. The working Squeezebox v3: - Connected through wireless to a linksys wireless router (this always worked before the slimserver upgrade). No hardware changes were made. Signal Strength:~80% - Gets IP address through DHCP - Slimserver v 6.5.1 running on Windows XP SP2 - Firmware version: 72 - Mac Address: 00 04 20 06 3C 3E - Connected through the analog outputs to a Harman/Kardon AVR7300. Slimserver: - I'm pretty sure that I have installed the 6.5.2 archive (I still have the archive so I can send the checksum if necessary) but I read: SlimServer Version: 6.5.1 - 11206 - Windows XP - EN - cp1252 Server IP address: 155.165.175.110 Perl Version: 5.8.8 MSWin32-x86-multi-thread MySQL Version: 5.0.22-community-nt - Running on a Celeron 1.6GHz (dedicated to just that. CPU load 2-3%) - 512MB of RAM - 98% of Data is encoded with FLAC. The rest are MP3s. Basically how can I debug this? Is there a way to log what's happening in the squeezebox before the resetoccurs? The fact that one works and the other doesn't, puzzles me. So far I've ran slimserver with debug (C:\Program Files\SlimServer\server>slim.exe --d_startup) and I've checked in all the debug messages in the server settings "debugging". This is the ouput that I get: C:\Program Files\SlimServer\server>slim.exe --d_startup Got @INC containing: C:/Program Files/SlimServer/server C:\Program Files\SlimServer\server Extended @INC to contain: C:\Program Files\SlimServer\server\CPAN\arch\5.8\MSWin32-x86-multi-thread C:\Program Files\SlimServer\server\CPAN\arch\5.8\MSWin32-x86-multi-thread\auto C:\Program Files\SlimServer\server\CPAN\arch\5.8.8\MSWin32-x86-multi-thread C:\Program Files\SlimServer\server\CPAN\arch\5.8.8\MSWin32-x86-multi-thread\auto <snip>...(no errors) Loaded module: [Time::HiRes] ok! Loaded module: [DBD::mysql] ok! Loaded module: [DBI] ok! Loaded module: [XML::Parser::Expat] ok! Loaded module: [HTML::Parser] ok! Loaded module: [Compress::Zlib] ok! Loaded module: [Digest::SHA1] ok! Loaded module: [YAML::Syck] ok! Loaded module: [GD] ok! Loaded module: [Locale::Hebrew] ok! <snip>...(no errors) Loaded module: [Slim::Utils::PerlRunTime] ok! Loaded module: [Plugins::Rescan] ok! Loaded module: [Plugins::RS232::Plugin] ok! Loaded module: [Plugins::PreventStandby::Plugin] ok! Loaded module: [Plugins::MusicMagic::Plugin] ok! Loaded module: [Plugins::Visualizer] ok! Loaded module: [Plugins::CLI] ok! Loaded module: [Plugins::Snow] ok! Loaded module: [Plugins::Rhapsody::Plugin] ok! Loaded module: [Plugins::RandomPlay::Plugin] ok! Loaded module: [Plugins::RPC] ok! Loaded module: [Plugins::Health::Plugin] ok! Loaded module: [Plugins::DateTime::Plugin] ok! Loaded module: [Plugins::RadioIO::Plugin] ok! Loaded module: [Plugins::SavePlaylist] ok! Loaded module: [Plugins::Podcast::Plugin] ok! Loaded module: [Plugins::DigitalInput::Plugin] ok! Loaded module: [Plugins::xPL] ok! Loaded module: [Plugins::Picks::Plugin] ok! Loaded module: [Plugins::RssNews] ok! Loaded module: [Plugins::Live365::Plugin] ok! Loaded module: [Plugins::LMA::Plugin] ok! Loaded module: [Plugins::ShoutcastBrowser::Plugin] ok! Loaded module: [Plugins::RadioTime::Plugin] ok! Loaded module: [Plugins::Visualizer] ok! Loaded module: [Plugins::iTunes::Plugin] ok! Loaded module: [Plugins::CLI] ok! Loaded module: [Plugins::Snow] ok! Loaded module: [Plugins::Rhapsody::Plugin] ok! Loaded module: [Plugins::RandomPlay::Plugin] ok! Loaded module: [Plugins::RPC] ok! Loaded module: [Plugins::Health::Plugin] ok! Loaded module: [Plugins::DateTime::Plugin] ok! Loaded module: [Plugins::RadioIO::Plugin] ok! Loaded module: [Plugins::SavePlaylist] ok! Loaded module: [Plugins::Podcast::Plugin] ok! Loaded module: [Plugins::SlimTris] ok! Loaded module: [Plugins::MoodLogic::Plugin] ok! Loaded module: [Plugins::DigitalInput::Plugin] ok! Loaded module: [Plugins::xPL] ok! Loaded module: [Plugins::Picks::Plugin] ok! Loaded module: [Plugins::RssNews] ok! Loaded module: [Plugins::Live365::Plugin] ok! Loaded module: [Plugins::LMA::Plugin] ok! Loaded module: [Plugins::ShoutcastBrowser::Plugin] ok! Loaded module: [Plugins::RadioTime::Plugin] ok! 2007-03-15 22:53:45.6240 The URL to access SlimServer is now: http://Squeeze-server:9000/ Loaded module: [Slim::Display::Squeezebox2] ok! Loaded module: [Slim::Display::Squeezebox2] ok! Loaded module: [Slim::Formats::FLAC] ok! After this the file played for about 20sec. Then the board reset and it continued to play and reset again... but strangely it is not logged here. Then I've synchronized the two squeezebox to play the exact same song. One keeps playing and the other one keeps resetting every 20seconds. I've let this run all night last night and I got this additional information this morning: 2007-03-16 07:56:47.0648 Backtrace: frame 0: Slim::Utils::Misc::assert (/PerlApp/Slim/Hardware/IR.pm line 68) frame 1: Slim::Hardware::IR::enqueue (/PerlApp/Slim/Networking/Slimproto.pm l ine 469) frame 2: Slim::Networking::Slimproto::_ir_handler (/PerlApp/Slim/Networking/S limproto.pm line 387) frame 3: Slim::Networking::Slimproto::client_readable (/PerlApp/Slim/Networki ng/Select.pm line 238) frame 4: (eval) (/PerlApp/Slim/Networking/Select.pm line 238) frame 5: Slim::Networking::Select::select (slimserver.pl line 492) frame 6: main::idle (slimserver.pl line 445) frame 7: main::main (slimserver.pl line 58) frame 8: PerlSvc::Interactive (perlsvc.pl line 1486) frame 9: PerlSvc::_interactive (slimserver.pl line 0) frame 10: (eval) (slimserver.pl line 0) Here's the problem. /PerlApp/Slim/Hardware/IR.pm, line 68: 2007-03-16 08:06:29.0027 Backtrace: frame 0: Slim::Utils::Misc::assert (/PerlApp/Slim/Hardware/IR.pm line 68) frame 1: Slim::Hardware::IR::enqueue (/PerlApp/Slim/Networking/Slimproto.pm l ine 469) frame 2: Slim::Networking::Slimproto::_ir_handler (/PerlApp/Slim/Networking/S limproto.pm line 387) frame 3: Slim::Networking::Slimproto::client_readable (/PerlApp/Slim/Networki ng/Select.pm line 238) frame 4: (eval) (/PerlApp/Slim/Networking/Select.pm line 238) frame 5: Slim::Networking::Select::select (slimserver.pl line 492) frame 6: main::idle (slimserver.pl line 445) frame 7: main::main (slimserver.pl line 58) frame 8: PerlSvc::Interactive (perlsvc.pl line 1486) frame 9: PerlSvc::_interactive (slimserver.pl line 0) frame 10: (eval) (slimserver.pl line 0) Here's the problem. /PerlApp/Slim/Hardware/IR.pm, line 68: Does that error message mean something to anyone? It seems to indicate an issue with the IR interface. Any help in debugging this issue would be appreciated. Hopefully I don't have a faulty hardware device. Thanks Tarus -- Tarus ------------------------------------------------------------------------ Tarus's Profile: http://forums.slimdevices.com/member.php?userid=10729 View this thread: http://forums.slimdevices.com/showthread.php?t=33683 _______________________________________________ discuss mailing list [email protected] http://lists.slimdevices.com/lists/listinfo/discuss
