As far as I know. If you are sending vlan tagged traffic yes. (If it's untagged no).
Aaron On Wed, Sep 7, 2011 at 11:47 PM, Jen-Wei Hu <[email protected]> wrote: > Hi, > It works well if the cisco switch contains the Vlan IDs which used in VMs. > So, we have to manually add all Vlan IDs (which will be used in VMs) in > advance? > > Thanks, > Jen-Wei > On Thu, Sep 8, 2011 at 11:30 AM, Aaron Rosen <[email protected]> wrote: >> >> Is the trunk port on the cisco switch set to be the same vlan id that >> is coming out of the VMs? >> >> Aaron >> >> On Wed, Sep 7, 2011 at 10:34 PM, Ben Pfaff <[email protected]> wrote: >> > I only know how to configure OVS. >> > >> > On Thu, Sep 08, 2011 at 10:31:38AM +0800, Jen-Wei Hu wrote: >> >> Thanks for your quick reply. Could you kindly share and describe how >> >> other >> >> brands switch must configure when creating new VLAN ID on OVS? >> >> >> >> On Thu, Sep 8, 2011 at 10:01 AM, Ben Pfaff <[email protected]> wrote: >> >> >> >> > No, I don't know how to configure a Cisco switch. I hope that >> >> > someone >> >> > else can suggest how to do this. >> >> > >> >> > On Thu, Sep 08, 2011 at 09:39:44AM +0800, Jen-Wei Hu wrote: >> >> > > Sorry for the poor English. I try to describe my problem clearly. >> >> > Currently, >> >> > > we could configure the VLAN function of OVS successfully and work >> >> > > well >> >> > when >> >> > > our two servers (installed OVS) directly connected via a network >> >> > > cable. >> >> > But >> >> > > when we deploy these two servers to our physical switch, we meet a >> >> > problem >> >> > > that the VMs on these servers (have the same VLAN ID) could not >> >> > > ping >> >> > > successfully. Our physical switch is Cisco 3750 and we have set the >> >> > ports, >> >> > > connected two servers, to be trunking ports. Would you have any >> >> > experiences >> >> > > for this situation? >> >> > > >> >> > > Thanks again >> >> > > Jen-Wei >> >> > > On Wed, Sep 7, 2011 at 11:16 PM, Ben Pfaff <[email protected]> wrote: >> >> > > >> >> > > > On Wed, Sep 07, 2011 at 05:11:58PM +0800, Jen-Wei Hu wrote: >> >> > > > > Recently, we would like to let our deployed VMs that could be >> >> > separated >> >> > > > by >> >> > > > > VLAN. In this link ( >> >> > > > > >> >> > > > >> >> > >> >> > http://openvswitch.org/support/config-cookbooks/vlan-configuration-cookbook/ >> >> > > > ), >> >> > > > > it mentions that we should set up trunking ports on physical >> >> > switches. >> >> > > > Our >> >> > > > > switch is a port-based to set VLAN ID, so we need to manually >> >> > > > > add all >> >> > > > > created VLAN IDs in OVS? That is the only way to do? We >> >> > > > > appreciate >> >> > > > someone >> >> > > > > could share nice experience or advice for this problem. Thanks! >> >> > > > >> >> > > > I don't understand the question. Are you asking how to configure >> >> > > > OVS >> >> > or >> >> > > > how to configure your physical switch? >> >> > > > >> >> > >> > _______________________________________________ >> > discuss mailing list >> > [email protected] >> > http://openvswitch.org/mailman/listinfo/discuss >> > >> >> >> >> -- >> Aaron O. Rosen >> Masters Student - Network Communication >> 306B Fluor Daniel > > -- Aaron O. Rosen Masters Student - Network Communication 306B Fluor Daniel _______________________________________________ discuss mailing list [email protected] http://openvswitch.org/mailman/listinfo/discuss
