hi, I set max_backoff as 10 sec and then after every 10 sec i saw controller status as *"connecting*" using *ovs-vsctl list controller* command but i can not see any echo request message being sent from switch to controller ip after max_backoff interval is over.
On Thu, Mar 15, 2012 at 10:16 AM, Ben Pfaff <[email protected]> wrote: > No, I didn't say that, and that is not what the documentation says. > Please read the documentation. > > On Thu, Mar 15, 2012 at 10:13:01AM +0530, selen jia wrote: > > hi, > > so what you say is if i set max_backoff 10 sec then after 10 seconds > switch > > and controller connection should disconnect.. > > but that is not happening. > > > > On Thu, Mar 15, 2012 at 9:50 AM, Ben Pfaff <[email protected]> wrote: > > > > > OK, that's the same definition I had. > > > > > > You must be doing something wrong. This works fine for everyone else. > > > > > > On Thu, Mar 15, 2012 at 09:27:32AM +0530, selen jia wrote: > > > > hi, > > > > > > > > In openflow spec 1.0 it is written - > > > > *"In the case that a switch loses contact with the controller, as a > > > result > > > > of a echo > > > > * > > > > *request timeout, TLS session timeout, or other disconnection, it > should > > > > attempt* > > > > *to contact one or more backup controllers."* > > > > > > > > so im trying ro simulate this scenario where switch looses contact > after > > > > echo request timeout. > > > > > > > > > > > > > > > > On Wed, Mar 14, 2012 at 10:10 PM, Ben Pfaff <[email protected]> wrote: > > > > > > > > > Perhaps your definition of "echo session timeout" is different from > > > > > mine. Please tell me what it means to you. > > > > > > > > > > On Wed, Mar 14, 2012 at 03:10:44PM +0530, selen jia wrote: > > > > > > hi, > > > > > > i set max_backoff and inactivity_probe as 10 sec but there is no > > > response > > > > > > of this configuration in network analyzer . i have checked with > both > > > > > > situations - when controller is connected and not connected . > > > > > > But its seems like max_backoff is a interval time and > > > inactivity_probe > > > > > is a > > > > > > kind of ping. > > > > > > > > > > > > so how it will work as a echo session timeout? > > > > > > > > > > > > On Wed, Mar 14, 2012 at 10:14 AM, Justin Pettit < > [email protected]> > > > > > wrote: > > > > > > > > > > > > > Look at "max_backoff" and "inactivity_probe". > > > > > > > > > > > > > > --Justin > > > > > > > > > > > > > > > > > > > > > On Mar 13, 2012, at 8:19 PM, selen jia <[email protected]> > wrote: > > > > > > > > > > > > > > Hi, > > > > > > > there is no information for echo request timeout in > > > > > > > ovs-vswitchd.conf.db . > > > > > > > > > > > > > > On Wed, Mar 14, 2012 at 8:42 AM, Ben Pfaff <[email protected]> > wrote: > > > > > > > > > > > > > >> There is no way to set the TLS session timeout. > > > > > > >> > > > > > > >> ovs-vswitchd.conf.db(5) documents how to set the echo request > > > timeout. > > > > > > >> > > > > > > >> On Wed, Mar 14, 2012 at 08:21:16AM +0530, selen jia wrote: > > > > > > >> > hi, > > > > > > >> > i need to know how to set TLS session timeout and echo > request > > > time > > > > > > >> out ? > > > > > > >> > > > > > > > >> > On Tue, Mar 13, 2012 at 9:58 PM, Ben Pfaff <[email protected]> > > > wrote: > > > > > > >> > > > > > > > >> > > There is no limit on retries. > > > > > > >> > > > > > > > > >> > > On Tue, Mar 13, 2012 at 05:28:23PM +0530, selen jia wrote: > > > > > > >> > > > *Hii,* > > > > > > >> > > > * > > > > > > >> > > > * > > > > > > >> > > > i m using openvswitch 1.2.2 and nox as controller , > now if > > > > > switch > > > > > > >> loses > > > > > > >> > > > contact form controller due to lan issue , switch > keeps on > > > > > sending > > > > > > >> tcp > > > > > > >> > > > request to controller ip > > > > > > >> > > > i believe there should be limited number of retry.. but > i > > > dont > > > > > see > > > > > > >> it. > > > > > > >> > > > > > > > > > >> > > > * > > > > > > >> > > > > > > > > > >> > > > i need to know how to set TLS session timeout and echo > > > request > > > > > time > > > > > > >> out > > > > > > >> > > ?* > > > > > > >> > > > * > > > > > > >> > > > * > > > > > > >> > > > On Tue, Feb 7, 2012 at 11:15 AM, Ben Pfaff < > [email protected]> > > > > > wrote: > > > > > > >> > > > > > > > > > >> > > > > On Tue, Feb 07, 2012 at 10:52:55AM +0530, selen jia > wrote: > > > > > > >> > > > > > How can i set this NXT_ROLE_REQUEST parameter from > ovs > > > > > > >> commandline. > > > > > > >> > > > > > > > > > > >> > > > > You cannot. > > > > > > >> > > > > > > > > > > >> > > > > > > > > >> > > > > > > > > > > > > > > _______________________________________________ > > > > > > > discuss mailing list > > > > > > > [email protected] > > > > > > > http://openvswitch.org/mailman/listinfo/discuss > > > > > > > > > > > > > > > > > > > > > > >
_______________________________________________ discuss mailing list [email protected] http://openvswitch.org/mailman/listinfo/discuss
