---
 dnsmasq.conf.example | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/dnsmasq.conf.example b/dnsmasq.conf.example
index e58c812..e523209 100644
--- a/dnsmasq.conf.example
+++ b/dnsmasq.conf.example
@@ -27,8 +27,8 @@
 
 # Replies which are not DNSSEC signed may be legitimate, because the domain
 # is unsigned, or may be forgeries. Setting this option tells dnsmasq to
-# check that an unsigned reply is OK, by finding a secure proof that a DS 
-# record somewhere between the root and the domain does not exist. 
+# check that an unsigned reply is OK, by finding a secure proof that a DS
+# record somewhere between the root and the domain does not exist.
 # The cost of setting this is that even queries in unsigned domains will need
 # one or more extra DNS queries to verify.
 #dnssec-check-unsigned
@@ -183,11 +183,11 @@
 #dhcp-range=1234::2, 1234::500, 64, 12h
 
 # Do Router Advertisements, BUT NOT DHCP for this subnet.
-#dhcp-range=1234::, ra-only 
+#dhcp-range=1234::, ra-only
 
 # Do Router Advertisements, BUT NOT DHCP for this subnet, also try and
-# add names to the DNS for the IPv6 address of SLAAC-configured dual-stack 
-# hosts. Use the DHCPv4 lease to derive the name, network segment and 
+# add names to the DNS for the IPv6 address of SLAAC-configured dual-stack
+# hosts. Use the DHCPv4 lease to derive the name, network segment and
 # MAC address and assume that the host will also have an
 # IPv6 address calculated using the SLAAC algorithm.
 #dhcp-range=1234::, ra-names
@@ -210,9 +210,9 @@
 #dhcp-range=1234::, ra-stateless, ra-names
 
 # Do router advertisements for all subnets where we're doing DHCPv6
-# Unless overridden by ra-stateless, ra-names, et al, the router 
+# Unless overridden by ra-stateless, ra-names, et al, the router
 # advertisements will have the M and O bits set, so that the clients
-# get addresses and configuration from DHCPv6, and the A bit reset, so the 
+# get addresses and configuration from DHCPv6, and the A bit reset, so the
 # clients don't use SLAAC addresses.
 #enable-ra
 
@@ -285,11 +285,11 @@
 # any machine with Ethernet address starting 11:22:33:
 #dhcp-host=11:22:33:*:*:*,set:red
 
-# Give a fixed IPv6 address and name to client with 
+# Give a fixed IPv6 address and name to client with
 # DUID 00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2
 # Note the MAC addresses CANNOT be used to identify DHCPv6 clients.
 # Note also that the [] around the IPv6 address are obligatory.
-#dhcp-host=id:00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2, fred, [1234::5] 
+#dhcp-host=id:00:01:00:01:16:d2:83:fc:92:d4:19:e2:d8:b2, fred, [1234::5]
 
 # Ignore any clients which are not specified in dhcp-host lines
 # or /etc/ethers. Equivalent to ISC "deny unknown-clients".
@@ -345,7 +345,7 @@
 # Send DHCPv6 option. Note [] around IPv6 addresses.
 #dhcp-option=option6:dns-server,[1234::77],[1234::88]
 
-# Send DHCPv6 option for namservers as the machine running 
+# Send DHCPv6 option for namservers as the machine running
 # dnsmasq and another.
 #dhcp-option=option6:dns-server,[::],[1234::88]
 
@@ -550,7 +550,7 @@
 # Set the DHCP server to enable DHCPv4 Rapid Commit Option per RFC 4039.
 # In this mode it will respond to a DHCPDISCOVER message including a Rapid 
Commit
 # option with a DHCPACK including a Rapid Commit option and fully committed 
address
-# and configuration information. This must only be enabled if either the 
server is 
+# and configuration information. This must only be enabled if either the 
server is
 # the only server for the subnet, or multiple servers are present and they each
 # commit a binding for all clients.
 #dhcp-rapid-commit
-- 
2.1.4


_______________________________________________
Dnsmasq-discuss mailing list
Dnsmasq-discuss@lists.thekelleys.org.uk
http://lists.thekelleys.org.uk/mailman/listinfo/dnsmasq-discuss

Reply via email to