On Wed, 2010-08-18 at 18:23 +0200, Anders Logg wrote: > On Wed, Aug 18, 2010 at 08:31:55PM +0530, Harish Narayanan wrote: > > On 8/18/10 8:23 PM, Garth N. Wells wrote: > > > On Wed, 2010-08-18 at 16:16 +0200, Anders Logg wrote: > > >> On Wed, Aug 18, 2010 at 03:40:47PM +0200, Anders Logg wrote: > > >>> On Wed, Aug 18, 2010 at 06:58:24PM +0530, Harish Narayanan wrote: > > >>>> On 8/18/10 6:32 PM, Anders Logg wrote: > > > > > > > > >>>> > > >>>> ================================================================================ > > >>>> SLEPc Configuration > > >>>> ================================================================================ > > >>>> > > >>>> SLEPc source directory: > > >>>> /Users/harish/Work/FEniCS/test/src/slepc-3.1-p1 > > >>>> SLEPc install directory: > > >>>> /Users/harish/Work/FEniCS/test > > >>>> PETSc directory: > > >>>> /Users/harish/Work/FEniCS/test > > >>>> Architecture "unknown" with double precision real numbers > > >>>> > > >>>> ** > > >>>> ** Before running "make" your PETSC_ARCH must be specified with: > > >>>> ** ** setenv PETSC_ARCH unknown (csh/tcsh) > > >>>> ** ** PETSC_ARCH=unknown ; export PETSC_ARCH (sh/bash) > > >>>> ** > > >>>> > > >>>> makefile:30: darwin10.0.0-cxx-opt/conf/slepcvariables: No such file or > > >>>> directory > > >>>> /Users/harish/Work/FEniCS/test/src/slepc-3.1-p1/conf/slepc_common_variables:2: > > >>>> /Users/harish/Work/FEniCS/test/src/slepc-3.1-p1/darwin10.0.0-cxx-opt/conf/slepcvariables: > > >>>> No such file or directory > > >>>> /Users/harish/Work/FEniCS/test/src/slepc-3.1-p1/conf/slepc_common_rules:78: > > >>>> /Users/harish/Work/FEniCS/test/src/slepc-3.1-p1/darwin10.0.0-cxx-opt/conf/slepcrules: > > >>>> No such file or directory > > >>>> make: *** No rule to make target > > >>>> `/Users/harish/Work/FEniCS/test/src/slepc-3.1-p1/darwin10.0.0-cxx-opt/conf/slepcrules'. > > >>>> Stop. > > >>>> Failure with exit status: 2 > > >>>> Exit message: There was a problem building slepc-3.1-p1. > > >>> > > >>> I get exactly the same thing. > > >> > > >> I have something that appears to work now. Will push when I have > > >> tested it. > > >> > > > > > > Check that it works with petsc commented out in the .platform file (but > > > already complied, e.g. on a previous run of dorsal). > > > > Dorsal is not designed to this way. You are supposed to > > > > skip:petsc > > > > (instead of commenting it out) in the packages list. Commenting out > > means dorsal knows nothing of petsc and slepc should fail. skip:petsc > > means dorsal knows about it but will skip compiling it. slepc will pick > > this up, and so will DOLFIN. > > > > Harish > > I made an attempt to fix this. Looking at petsconf.py in SLEPc, it > seems that one should not set PETSC_ARCH when building against an > installed version of PETSc, so I just made sure that PETSC_ARCH is > unset when Dorsal configures and builds SLEPc and that PETSC_DIR is > set to the installation directory. >
An option is if Doral using './configure --prefix=/foo/bar'. Then a prefix is not required. > It also seems that it doesn't really matter what we set PETSC_ARCH to > since we just build one version of PETSc. It's just a name and > it's not used by SLEPc. > Are you using SLEPc 3.1? Garth > -- > Anders _______________________________________________ Mailing list: https://launchpad.net/~dorsal Post to : [email protected] Unsubscribe : https://launchpad.net/~dorsal More help : https://help.launchpad.net/ListHelp
