I also used this manual to startup, I agree with Jake, that's a typo. Apart
from that, William, your "bindnetaddr" parameter should not end with a "0",
it's supposed to be the IP address your local host/node will use to monitor its
peers. Instead, replace it by the IP address your server has on network
192.168.1.0.
My own file looks like this :
---------------------------------------------8<-------------------------------------------------
# Please read the corosync.conf.5 manual page
compatibility: whitetank
totem {
version: 2
secauth: off
threads: 0
interface {
ringnumber: 0
bindnetaddr: 175.10.20.6
mcastaddr: 226.94.1.0
mcastport: 4000
}
interface {
ringnumber: 1
bindnetaddr: 195.165.5.245
mcastaddr: 226.94.1.1
mcastport: 4001
}
rrp_mode: active
}
logging {
fileline: off
to_stderr: no
to_logfile: yes
to_syslog: yes
logfile: /var/log/cluster/corosync.log
debug: off
timestamp: on
logger_subsys {
subsys: AMF
debug: off
}
}
amf {
mode: disabled
}
aisexec {
user: root
group: root
}
service {
# Load the Pacemaker Cluster Resource Manager
name: pacemaker
ver: 0
}
---------------------------------------------8<-------------------------------------------------
There are 2 interface entries because I have set 2 rings up, for cluster
monitoring. You might start with only one without problem, in which case I
guess you may remove the rrp_mode entry.
Now, from a more general prospective, I believe this is not the right mailing
list to post that kind of question, I believe you'd better do so in the
linux-ha one, you'd probably have a better reactivity...
HTH.
Best regards,
Pascal.
-----Message d'origine-----
De : [email protected]
[mailto:[email protected]] De la part de Jake Smith
Envoyé : jeudi 7 juin 2012 16:37
À : [email protected]
Objet : Re: [DRBD-user] Corosync Configuration
----- Original Message -----
> From: "William D Yount" <[email protected]>
> To: [email protected]
> Sent: Thursday, June 7, 2012 1:22:34 AM
> Subject: [DRBD-user] Corosync Configuration
>
>
>
>
>
> I am following this guide:
> http://www.clusterlabs.org/doc/en-US/Pacemaker/1.1/txt/Clusters_from_S
> cratch/Clusters_from_Scratch.txt
>
>
>
> I have two servers with two NICS each:
>
> Server 1:
>
> NIC-A: 10.89.99.31
>
> NIC-B: 192.168.1.5
>
> Server 2:
>
> NIC-A: 10.89.99.32
>
> NIC-B: 192.168.1.10
>
>
>
> I am at the section where I need to configure corosync.conf. I tried
> doing the command line:
>
> 1. export ais_port=4000
>
> 2. export ais_mcast=226.94.1.1
>
> 3. export ais_addr=`ip addr | grep “inet” | tail –n 1 | awk
> ‘{print $4}’ | sed s/255/0/
>
> 4. env | grep ais_ais_mcast=226.94.1.1
>
Looks like a typo to me in the guide though I'm not positive (and haven't
followed that guide) - I think there should only be ais_ once not twice.
I believe the command in the guide should read:
# env | grep ais_mcast=226.94.1.1ais_port=4000ais_addr=192.168.122.0
And what you should try instead of 4. above:
env | grep ais_mcast=226.94.1.1
HTH
Jake
_______________________________________________
drbd-user mailing list
[email protected]
http://lists.linbit.com/mailman/listinfo/drbd-user
_______________________________________________
drbd-user mailing list
[email protected]
http://lists.linbit.com/mailman/listinfo/drbd-user
