Hi,
I don't think is related to bonding, I've tried that using just 1 NIC, and the
problem still exist. Usually is those none active drbd partition will get
disconnect/reconnect,so yes, the more partition you add the more you see.
By the way, Ubuntu 13.04 is using DRBD 8.4.2, not sure it will sync with 8.3.x
or not.
>________________________________
> From: Gerald Brandt <[email protected]>
>To: Chris Tothill <[email protected]>
>Cc: [email protected]
>Sent: Thursday, June 27, 2013 11:57 AM
>Subject: Re: [DRBD-user] r0 ok, r1 PingAck did not arrive in time
>
>
>
>Hi,
>
>>________________________________
>
>From: "Chris Tothill" <[email protected]>
>>To: [email protected]
>>Sent: Thursday, June 27, 2013 5:42:54 AM
>>Subject: Re: [DRBD-user] r0 ok, r1 PingAck did not arrive in time
>>
>>
>>Are you using active/active channel bonding? If so I'd suggest trying
>>active/passive (or just a single direct connection with no bonding) and see
>>if that helps. If in doubt, simplify...
>>
>>
>>Incidentally, with gigE my experience is that you don't actually need a
>>'crossover' cable to do direct connection, a normal 'straight' cable works
>>just as well. I think this is because gigE uses all 4 pairs simultaneously in
>>both directions rather than one pair in each direction as 100M does.
>>
>>
>>Chris
>>
>>
>>
>>---------------------------
>>Christopher Tothill
>>Zone D Senior IT Support Specialist (Chemistry Unix Support)
>>W227, School of Chemistry, University of Bristol
>>Tel: (+44 117 33) 17045
>>[email protected]
>>---------------------------
>>
>>
>>On 27 June 2013 03:12, Gerald Brandt <[email protected]> wrote:
>>
>>Hi,
>>>
>>>I'm running Intel e1000 with crossover cable, and I just noticed in my log
>>>files I'm getting this:
>>>
>>>[3535162.766591] e1000e: eth1 NIC Link is Down
>>>[3535168.243278] e1000e: eth1 NIC Link is Up 10 Mbps Full Duplex, Flow
>>>Control: Rx/Tx
>>>[3535168.243282] e1000e 0000:02:00.0: eth1: 10/100 speed: disabling TSO
>>>[3535176.574432] e1000e: eth1 NIC Link is Down
>>>[3535178.495165] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow
>>>Control: Rx/Tx
>>>[3535214.602022] e1000e: eth1 NIC Link is Down
>>>[3535214.602465] e1000e 0000:02:00.0: eth1: Reset adapter
>>>[3535239.602540] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow
>>>Control: Rx/Tx
>>>
>>>Interesting.
>>>
>>>
>>>Gerald
>>>
>>>
>>>
>>I'm sticking with active/passive, and a double of check of my cable shows it
>>to be a regular one, nothing special about it.
>
>drbd0 pings/acks just fine, it's only drbd1 that fails, once or twice a day,
>at irregular times. Will it get worse if I add a third drbd resource to the
>same box?
>
>Gerald
>
>_______________________________________________
>drbd-user mailing list
>[email protected]
>http://lists.linbit.com/mailman/listinfo/drbd-user
>
>
>
_______________________________________________
drbd-user mailing list
[email protected]
http://lists.linbit.com/mailman/listinfo/drbd-user
