+ Stanimir
On Sat, Jan 14, 2017 at 09:49:01PM -0600, Andy Gross wrote:
> On Fri, Jan 13, 2017 at 04:24:38PM -0700, Jordan Crouse wrote:
> > On Fri, Jan 13, 2017 at 11:12:41AM -0600, Andy Gross wrote:
> > > On Mon, Nov 28, 2016 at 12:28:35PM -0700, Jordan Crouse wrote:
> > > > Add an interface to trigger the remote processor to reinitialize the GPU
> > > > zap shader on power-up.
> > > >
> > > > Signed-off-by: Jordan Crouse <jcro...@codeaurora.org>
> > > > ---
> > >
> > > <snip>
> > >
> > > > +int __qcom_scm_gpu_zap_resume(struct device *dev)
> > > > +{
> > > > + struct qcom_scm_desc desc = {0};
> > > > + struct arm_smccc_res res;
> > > > + int ret;
> > > > +
> > > > + desc.args[0] = 0;
> >
> > This is an opcode to force the state to resume.
> >
> > QCOM_SCM_BOOT_SET_STATE_RESUME perhaps? Or something similar but shorter.
> >
> > > > + desc.args[1] = 13;
> >
> > This is the same as the SCM id of the GPU but I think that is a coincidence.
> > We've always used it to identify the GPU in this call.
> >
> > QCOM_SCM_BOOT_SET_STATE_GPU would be fine here - or something similar.
> >
> > > Can I get a define here for these two? Or maybe a comment on what these
> > > values
> > > are?
> > >
> > > > + desc.arginfo = QCOM_SCM_ARGS(2);
> > > > +
> > > > + ret = qcom_scm_call(dev, QCOM_SCM_SVC_BOOT, 0x0A, &desc, &res);
> > >
> > > Same with the 0xA. We usually throw a #define in for the command
> > > definitions.
> >
> > 0x0A sets the state of the device - for us it is always 0 (resume) and
> > always
> > the GPU.
> >
> > #define QCOM_SCM_BOOT_SET_STATE 0x0A
> >
> > > Otherwise this all looks fine. If you can get back to me with either the
> > > values
> > > or a new patch I can include this in the next pull.
> >
> > I'll make the changes and start the song and dance, but you'll no doubt be
> > faster than I.
>
> I can just fix up the patch with the above. Thanks for the additional
> details.
The plot thickens. So I have a patch from Stanimir concerning another SCM call
that is using the same command and number of arguments. And it also concerns
setting state. I think that we need to roll a common API for setting the state
and then both of you can call it. That way we can kill two birds with one
stone.
Something along the lines of a function prototype:
int qcom_scm_set_remote_state(u32 state, u32 id)
{
return __qcom_scm_set_remote_state(__scm->dev, state, id);
}
EXPORT_SYMBOL(qcom_scm_set_remote_state);
where state is the state you want set, and id is the identifier of the remote
proc.
Does this make sense for both of your use cases?
Andy
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
