On Thu, May 11, 2017 at 04:56:22PM -0700, Eric Anholt wrote:
> BCM2835's PLLD_DSI1 divider doesn't give us many choices for our pixel
> clocks, so to support panels on the Raspberry Pi we need to set a
> higher pixel clock rate than requested and adjust the mode we program
> to extend out the HFP so that the refresh rate matches.
>
> Signed-off-by: Eric Anholt <e...@anholt.net>
Yeah, this is what mode_fixup is for (or the fancier atomic_check, but no
benefit with using that one here).
Acked-by: Daniel Vetter <daniel.vet...@ffwll.ch>
> ---
> drivers/gpu/drm/vc4/vc4_dsi.c | 112
> ++++++++++++++++++++++++++++++++----------
> 1 file changed, 86 insertions(+), 26 deletions(-)
>
> diff --git a/drivers/gpu/drm/vc4/vc4_dsi.c b/drivers/gpu/drm/vc4/vc4_dsi.c
> index fb54a9d10360..62cb3b0d0345 100644
> --- a/drivers/gpu/drm/vc4/vc4_dsi.c
> +++ b/drivers/gpu/drm/vc4/vc4_dsi.c
> @@ -519,7 +519,8 @@ struct vc4_dsi {
> /* DSI channel for the panel we're connected to. */
> u32 channel;
> u32 lanes;
> - enum mipi_dsi_pixel_format format;
> + u32 format;
> + u32 divider;
> u32 mode_flags;
>
> /* Input clock from CPRMAN to the digital PHY, for the DSI
> @@ -817,13 +818,67 @@ static void vc4_dsi_encoder_disable(struct drm_encoder
> *encoder)
> pm_runtime_put(dev);
> }
>
> +/* Extends the mode's blank intervals to handle BCM2835's integer-only
> + * DSI PLL divider.
> + *
> + * On 2835, PLLD is set to 2Ghz, and may not be changed by the display
> + * driver since most peripherals are hanging off of the PLLD_PER
> + * divider. PLLD_DSI1, which drives our DSI bit clock (and therefore
> + * the pixel clock), only has an integer divider off of DSI.
> + *
> + * To get our panel mode to refresh at the expected 60Hz, we need to
> + * extend the horizontal blank time. This means we drive a
> + * higher-than-expected clock rate to the panel, but that's what the
> + * firmware (which ) does too.
> + */
> +static bool vc4_dsi_encoder_mode_fixup(struct drm_encoder *encoder,
> + const struct drm_display_mode *mode,
> + struct drm_display_mode *adjusted_mode)
> +{
> + struct vc4_dsi_encoder *vc4_encoder = to_vc4_dsi_encoder(encoder);
> + struct vc4_dsi *dsi = vc4_encoder->dsi;
> + struct clk *phy_parent = clk_get_parent(dsi->pll_phy_clock);
> + unsigned long parent_rate = clk_get_rate(phy_parent);
> + unsigned long pixel_clock_hz = mode->clock * 1000;
> + unsigned long pll_clock = pixel_clock_hz * dsi->divider;
> + int divider;
> +
> + /* Find what divider gets us a faster clock than the requested
> + * pixel clock.
> + */
> + for (divider = 1; divider < 8; divider++) {
> + if (parent_rate / divider < pll_clock) {
> + divider--;
> + break;
> + }
> + }
> +
> + /* Now that we've picked a PLL divider, calculate back to its
> + * pixel clock.
> + */
> + pll_clock = parent_rate / divider;
> + pixel_clock_hz = pll_clock / dsi->divider;
> +
> + /* Round up the clk_set_rate() request slightly, since
> + * PLLD_DSI1 is an integer divider and its rate selection will
> + * never round up.
> + */
> + adjusted_mode->clock = pixel_clock_hz / 1000 + 1;
> +
> + /* Given the new pixel clock, adjust HFP to keep vrefresh the same. */
> + adjusted_mode->htotal = pixel_clock_hz / (mode->vrefresh *
> mode->vtotal);
> + adjusted_mode->hsync_end += adjusted_mode->htotal - mode->htotal;
> + adjusted_mode->hsync_start += adjusted_mode->htotal - mode->htotal;
> +
> + return true;
> +}
> +
> static void vc4_dsi_encoder_enable(struct drm_encoder *encoder)
> {
> - struct drm_display_mode *mode = &encoder->crtc->mode;
> + struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
> struct vc4_dsi_encoder *vc4_encoder = to_vc4_dsi_encoder(encoder);
> struct vc4_dsi *dsi = vc4_encoder->dsi;
> struct device *dev = &dsi->pdev->dev;
> - u32 format = 0, divider = 0;
> bool debug_dump_regs = false;
> unsigned long hs_clock;
> u32 ui_ns;
> @@ -845,26 +900,7 @@ static void vc4_dsi_encoder_enable(struct drm_encoder
> *encoder)
> vc4_dsi_dump_regs(dsi);
> }
>
> - switch (dsi->format) {
> - case MIPI_DSI_FMT_RGB888:
> - format = DSI_PFORMAT_RGB888;
> - divider = 24 / dsi->lanes;
> - break;
> - case MIPI_DSI_FMT_RGB666:
> - format = DSI_PFORMAT_RGB666;
> - divider = 24 / dsi->lanes;
> - break;
> - case MIPI_DSI_FMT_RGB666_PACKED:
> - format = DSI_PFORMAT_RGB666_PACKED;
> - divider = 18 / dsi->lanes;
> - break;
> - case MIPI_DSI_FMT_RGB565:
> - format = DSI_PFORMAT_RGB565;
> - divider = 16 / dsi->lanes;
> - break;
> - }
> -
> - phy_clock = pixel_clock_hz * divider;
> + phy_clock = pixel_clock_hz * dsi->divider;
> ret = clk_set_rate(dsi->pll_phy_clock, phy_clock);
> if (ret) {
> dev_err(&dsi->pdev->dev,
> @@ -1049,8 +1085,9 @@ static void vc4_dsi_encoder_enable(struct drm_encoder
> *encoder)
>
> if (dsi->mode_flags & MIPI_DSI_MODE_VIDEO) {
> DSI_PORT_WRITE(DISP0_CTRL,
> - VC4_SET_FIELD(divider, DSI_DISP0_PIX_CLK_DIV) |
> - VC4_SET_FIELD(format, DSI_DISP0_PFORMAT) |
> + VC4_SET_FIELD(dsi->divider,
> + DSI_DISP0_PIX_CLK_DIV) |
> + VC4_SET_FIELD(dsi->format, DSI_DISP0_PFORMAT) |
> VC4_SET_FIELD(DSI_DISP0_LP_STOP_PERFRAME,
> DSI_DISP0_LP_STOP_CTRL) |
> DSI_DISP0_ST_END |
> @@ -1255,9 +1292,31 @@ static int vc4_dsi_host_attach(struct mipi_dsi_host
> *host,
>
> dsi->lanes = device->lanes;
> dsi->channel = device->channel;
> - dsi->format = device->format;
> dsi->mode_flags = device->mode_flags;
>
> + switch (device->format) {
> + case MIPI_DSI_FMT_RGB888:
> + dsi->format = DSI_PFORMAT_RGB888;
> + dsi->divider = 24 / dsi->lanes;
> + break;
> + case MIPI_DSI_FMT_RGB666:
> + dsi->format = DSI_PFORMAT_RGB666;
> + dsi->divider = 24 / dsi->lanes;
> + break;
> + case MIPI_DSI_FMT_RGB666_PACKED:
> + dsi->format = DSI_PFORMAT_RGB666_PACKED;
> + dsi->divider = 18 / dsi->lanes;
> + break;
> + case MIPI_DSI_FMT_RGB565:
> + dsi->format = DSI_PFORMAT_RGB565;
> + dsi->divider = 16 / dsi->lanes;
> + break;
> + default:
> + dev_err(&dsi->pdev->dev, "Unknown DSI format: %d.\n",
> + dsi->format);
> + return 0;
> + }
> +
> if (!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO)) {
> dev_err(&dsi->pdev->dev,
> "Only VIDEO mode panels supported currently.\n");
> @@ -1304,6 +1363,7 @@ static const struct mipi_dsi_host_ops vc4_dsi_host_ops
> = {
> static const struct drm_encoder_helper_funcs vc4_dsi_encoder_helper_funcs = {
> .disable = vc4_dsi_encoder_disable,
> .enable = vc4_dsi_encoder_enable,
> + .mode_fixup = vc4_dsi_encoder_mode_fixup,
> };
>
> static const struct of_device_id vc4_dsi_dt_match[] = {
> --
> 2.11.0
>
> _______________________________________________
> dri-devel mailing list
> dri-devel@lists.freedesktop.org
> https://lists.freedesktop.org/mailman/listinfo/dri-devel
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
