Handle both positive and negative dclk polarity,
according to bus_flags, taking care of this:

On A20 and similar SoCs, the only way to achieve Positive Edge
(Rising Edge), is setting dclk clock phase to 2/3(240°).
By default TCON works in Negative Edge(Falling Edge), this is why phase
is set to 0 in that case.
Unfortunately there's no way to logically invert dclk through IO_POL
register.
The only acceptable way to work, triple checked with scope,
is using clock phase set to 0° for Negative Edge and set to 240° for
Positive Edge.
On A33 and similar SoCs there would be a 90° phase option, but it divides
also dclk by 2.
This patch is a way to avoid quirks all around TCON and DOTCLOCK drivers
for using A33 90° phase divided by 2 and consequently increase code
complexity.

Signed-off-by: Giulio Benetti <giulio.bene...@micronovasrl.com>
---
 drivers/gpu/drm/sun4i/sun4i_tcon.c | 25 +++++++++++++++++++++++++
 1 file changed, 25 insertions(+)

diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c 
b/drivers/gpu/drm/sun4i/sun4i_tcon.c
index 8ee87c2..3f1455d 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
@@ -17,6 +17,7 @@
 #include <drm/drm_encoder.h>
 #include <drm/drm_modes.h>
 #include <drm/drm_of.h>
+#include <drm/drm_panel.h>
 
 #include <uapi/drm/drm_mode.h>
 
@@ -345,6 +346,9 @@ static void sun4i_tcon0_mode_set_lvds(struct sun4i_tcon 
*tcon,
 static void sun4i_tcon0_mode_set_rgb(struct sun4i_tcon *tcon,
                                     const struct drm_display_mode *mode)
 {
+       struct drm_panel *panel = tcon->panel;
+       struct drm_connector *connector = panel->connector;
+       struct drm_display_info display_info = connector->display_info;
        unsigned int bp, hsync, vsync;
        u8 clk_delay;
        u32 val = 0;
@@ -400,6 +404,27 @@ static void sun4i_tcon0_mode_set_rgb(struct sun4i_tcon 
*tcon,
        if (mode->flags & DRM_MODE_FLAG_PVSYNC)
                val |= SUN4I_TCON0_IO_POL_VSYNC_POSITIVE;
 
+       /*
+        * On A20 and similar SoCs, the only way to achieve Positive Edge
+        * (Rising Edge), is setting dclk clock phase to 2/3(240°).
+        * By default TCON works in Negative Edge(Falling Edge),
+        * this is why phase is set to 0 in that case.
+        * Unfortunately there's no way to logically invert dclk through
+        * IO_POL register.
+        * The only acceptable way to work, triple checked with scope,
+        * is using clock phase set to 0° for Negative Edge and set to 240°
+        * for Positive Edge.
+        * On A33 and similar SoCs there would be a 90° phase option,
+        * but it divides also dclk by 2.
+        * Following code is a way to avoid quirks all around TCON
+        * and DOTCLOCK drivers.
+        */
+       if (display_info.bus_flags & DRM_BUS_FLAG_PIXDATA_POSEDGE)
+               clk_set_phase(tcon->dclk, 240);
+
+       if (display_info.bus_flags & DRM_BUS_FLAG_PIXDATA_NEGEDGE)
+               clk_set_phase(tcon->dclk, 0);
+
        regmap_update_bits(tcon->regs, SUN4I_TCON0_IO_POL_REG,
                           SUN4I_TCON0_IO_POL_HSYNC_POSITIVE | 
SUN4I_TCON0_IO_POL_VSYNC_POSITIVE,
                           val);
-- 
2.7.4

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Reply via email to