Remove DT entries of hw block offsets and other target specific catalog
information for SDM845.

Signed-off-by: Sravanthi Kollukuduru <skoll...@codeaurora.org>
---
 .../devicetree/bindings/display/msm/dpu.txt        | 530 ---------------------
 1 file changed, 530 deletions(-)

diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt 
b/Documentation/devicetree/bindings/display/msm/dpu.txt
index 136f0d3..90cd3e0 100644
--- a/Documentation/devicetree/bindings/display/msm/dpu.txt
+++ b/Documentation/devicetree/bindings/display/msm/dpu.txt
@@ -19,61 +19,6 @@ Required properties
 - interrupt-controller: Mark the device node as an interrupt controller.
 - #interrupt-cells: Should be one. The first cell is interrupt number.
 - iommus: Specifies the SID's used by this context bank.
-- qcom,dpu-sspp-type:          Array of strings for DPU source surface pipes 
type information.
-                               A source pipe can be "vig", "rgb", "dma" or 
"cursor" type.
-                               Number of xin ids defined should match the 
number of offsets
-                               defined in property: qcom,dpu-sspp-off.
-- qcom,dpu-sspp-off:           Array of offset for DPU source surface pipes. 
The offsets
-                               are calculated from register "mdp_phys" defined 
in
-                               reg property + "dpu-off". The number of offsets 
defined here should
-                               reflect the amount of pipes that can be active 
in DPU for
-                               this configuration.
-- qcom,dpu-sspp-xin-id:                Array of VBIF clients ids (xins) 
corresponding
-                               to the respective source pipes. Number of xin 
ids
-                               defined should match the number of offsets
-                               defined in property: qcom,dpu-sspp-off.
-- qcom,dpu-ctl-off:            Array of offset addresses for the available ctl
-                               hw blocks within DPU, these offsets are
-                               calculated from register "mdp_phys" defined in
-                               reg property.  The number of ctl offsets defined
-                               here should reflect the number of control paths
-                               that can be configured concurrently on DPU for
-                               this configuration.
-- qcom,dpu-wb-off:             Array of offset addresses for the programmable
-                               writeback blocks within DPU.
-- qcom,dpu-wb-xin-id:          Array of VBIF clients ids (xins) corresponding
-                               to the respective writeback. Number of xin ids
-                               defined should match the number of offsets
-                               defined in property: qcom,dpu-wb-off.
-- qcom,dpu-mixer-off:          Array of offset addresses for the available
-                               mixer blocks that can drive data to panel
-                               interfaces. These offsets are be calculated from
-                               register "mdp_phys" defined in reg property.
-                               The number of offsets defined should reflect the
-                               amount of mixers that can drive data to a panel
-                               interface.
-- qcom,dpu-dspp-top-off:               Offset address for the dspp top block.
-                               The offset is calculated from register 
"mdp_phys"
-                               defined in reg property.
-- qcom,dpu-dspp-off:           Array of offset addresses for the available dspp
-                               blocks. These offsets are calculated from
-                               register "mdp_phys" defined in reg property.
-- qcom,dpu-pp-off:             Array of offset addresses for the available
-                               pingpong blocks. These offsets are calculated
-                               from register "mdp_phys" defined in reg 
property.
-- qcom,dpu-pp-slave:           Array of flags indicating whether each ping pong
-                               block may be configured as a pp slave.
-- qcom,dpu-intf-off:           Array of offset addresses for the available DPU
-                               interface blocks that can drive data to a
-                               panel controller. The offsets are calculated
-                               from "mdp_phys" defined in reg property. The 
number
-                               of offsets defined should reflect the number of
-                               programmable interface blocks available in 
hardware.
-- qcom,dpu-mixer-blend-op-off  Array of offset addresses for the available
-                               blending stages. The offsets are relative to
-                               qcom,dpu-mixer-off.
-- qcom,dpu-mixer-pair-mask     Array of mixer numbers that can be paired with
-                               mixer number corresponding to the array index.
 
 Optional properties:
 - clock-rate:          List of clock rates in Hz.
@@ -93,182 +38,6 @@ Optional properties:
                                -- qcom,supply-post-on-sleep: time to sleep 
(ms) after turning on
                                -- qcom,supply-pre-off-sleep: time to sleep 
(ms) before turning off
                                -- qcom,supply-post-off-sleep: time to sleep 
(ms) after turning off
-- qcom,dpu-sspp-src-size:      A u32 value indicates the address range for 
each sspp.
-- qcom,dpu-mixer-size:         A u32 value indicates the address range for 
each mixer.
-- qcom,dpu-ctl-size:           A u32 value indicates the address range for 
each ctl.
-- qcom,dpu-dspp-size:          A u32 value indicates the address range for 
each dspp.
-- qcom,dpu-intf-size:          A u32 value indicates the address range for 
each intf.
-- qcom,dpu-dsc-size:           A u32 value indicates the address range for 
each dsc.
-- qcom,dpu-cdm-size:           A u32 value indicates the address range for 
each cdm.
-- qcom,dpu-pp-size:            A u32 value indicates the address range for 
each pingpong.
-- qcom,dpu-wb-size:            A u32 value indicates the address range for 
each writeback.
-- qcom,dpu-len:                        A u32 entry for DPU address range.
-- qcom,dpu-intf-max-prefetch-lines:    Array of u32 values for max prefetch 
lines on
-                               each interface.
-- qcom,dpu-sspp-linewidth:     A u32 value indicates the max sspp line width.
-- qcom,dpu-mixer-linewidth:    A u32 value indicates the max mixer line width.
-- qcom,dpu-wb-linewidth:       A u32 value indicates the max writeback line 
width.
-- qcom,dpu-sspp-scale-size:    A u32 value indicates the scaling block size on 
sspp.
-- qcom,dpu-mixer-blendstages:  A u32 value indicates the max mixer blend 
stages for
-                               alpha blending.
-- qcom,dpu-qseed-type:         A string entry indiates qseed support on sspp 
and wb.
-                               It supports "qssedv3" and "qseedv2" entries for 
qseed
-                               type. By default "qseedv2" is used if this 
optional property
-                               is not defined.
-- qcom,dpu-csc-type:           A string entry indicates csc support on sspp 
and wb.
-                               It supports "csc" and "csc-10bit" entries for 
csc
-                               type.
-- qcom,dpu-highest-bank-bit:   A u32 property to indicate GPU/Camera/Video 
highest memory
-                               bank bit used for tile format buffers.
-- qcom,dpu-ubwc-version:       Property to specify the UBWC feature version.
-- qcom,dpu-ubwc-static:        Property to specify the default UBWC static
-                               configuration value.
-- qcom,dpu-ubwc-swizzle:       Property to specify the default UBWC swizzle
-                               configuration value.
-- qcom,dpu-panic-per-pipe:     Boolean property to indicate if panic signal
-                               control feature is available on each source 
pipe.
-- qcom,dpu-has-src-split:      Boolean property to indicate if source split
-                               feature is available or not.
-- qcom,dpu-has-dim-layer:      Boolean property to indicate if mixer has dim 
layer
-                               feature is available or not.
-- qcom,dpu-has-idle-pc:                Boolean property to indicate if target 
has idle
-                               power collapse feature available or not.
-- qcom,dpu-has-mixer-gc:       Boolean property to indicate if mixer has gamma 
correction
-                               feature available or not.
-- qcom,dpu-has-dest-scaler:    Boolean property to indicate if destination 
scaler
-                               feature is available or not.
-- qcom,dpu-max-dest-scaler-input-linewidth: A u32 value indicates the
-                               maximum input line width to destination scaler.
-- qcom,dpu-max-dest-scaler-output-linewidth: A u32 value indicates the
-                               maximum output line width of destination scaler.
-- qcom,dpu-dest-scaler-top-off: A u32 value provides the
-                               offset from mdp base to destination scaler 
block.
-- qcom,dpu-dest-scaler-top-size: A u32 value indicates the address range for 
ds top
-- qcom,dpu-dest-scaler-off:    Array of u32 offsets indicate the qseed3 scaler 
blocks
-                               offset from destination scaler top offset.
-- qcom,dpu-dest-scaler-size:    A u32 value indicates the address range for 
each scaler block
-- qcom,dpu-sspp-clk-ctrl:      Array of offsets describing clk control
-                               offsets for dynamic clock gating. 1st value
-                               in the array represents offset of the control
-                               register. 2nd value represents bit offset within
-                               control register. Number of offsets defined 
should
-                               match the number of offsets defined in
-                               property: qcom,dpu-sspp-off
-- qcom,dpu-sspp-clk-status:    Array of offsets describing clk status
-                               offsets for dynamic clock gating. 1st value
-                               in the array represents offset of the status
-                               register. 2nd value represents bit offset within
-                               control register. Number of offsets defined 
should
-                               match the number of offsets defined in
-                               property: qcom,dpu-sspp-off.
-- qcom,dpu-sspp-excl-rect:     Array of u32 values indicating exclusion 
rectangle
-                               support on each sspp.
-- qcom,dpu-sspp-smart-dma-priority:    Array of u32 values indicating hw pipe
-                                       priority of secondary rectangles when 
smart dma
-                                       is supported. Number of priority values 
should
-                                       match the number of offsets defined in
-                                       qcom,dpu-sspp-off node. Zero indicates 
no support
-                                       for smart dma for the sspp.
-- qcom,dpu-smart-dma-rev:      A string entry indicating the smart dma version
-                               supported on the device. Supported entries are
-                               "smart_dma_v1" and "smart_dma_v2".
-- qcom,dpu-intf-type:          Array of string provides the interface type 
information.
-                               Possible string values
-                                       "dsi" - dsi display interface
-                                       "dp" - Display Port interface
-                                       "hdmi" - HDMI display interface
-                               An interface is considered as "none" if 
interface type
-                               is not defined.
-- qcom,dpu-off:                        DPU offset from "mdp_phys" defined in 
reg property.
-- qcom,dpu-cdm-off:            Array of offset addresses for the available
-                               cdm blocks. These offsets will be calculated 
from
-                               register "mdp_phys" defined in reg property.
-- qcom,dpu-vbif-off:           Array of offset addresses for the available
-                               vbif blocks. These offsets will be calculated 
from
-                               register "vbif_phys" defined in reg property.
-- qcom,dpu-vbif-size:          A u32 value indicates the vbif block address 
range.
-- qcom,dpu-te-off:             A u32 offset indicates the te block offset on 
pingpong.
-                               This offset is 0x0 by default.
-- qcom,dpu-te2-off:            A u32 offset indicates the te2 block offset on 
pingpong.
-- qcom,dpu-te-size:            A u32 value indicates the te block address 
range.
-- qcom,dpu-te2-size:           A u32 value indicates the te2 block address 
range.
-- qcom,dpu-dsc-off:            A u32 offset indicates the dsc block offset on 
pingpong.
-- qcom,dpu-dither-off:         A u32 offset indicates the dither block offset 
on pingpong.
-- qcom,dpu-dither-version:     A u32 value indicates the dither block version.
-- qcom,dpu-dither-size:                A u32 value indicates the dither block 
address range.
-- qcom,dpu-sspp-vig-blocks:    A node that lists the blocks inside the VIG 
hardware. The
-                               block entries will contain the offset and 
version (if needed)
-                               of each feature block. The presence of a block 
entry
-                               indicates that the SSPP VIG contains that 
feature hardware.
-                               e.g. qcom,dpu-sspp-vig-blocks
-                               -- qcom,dpu-vig-csc-off: offset of CSC hardware
-                               -- qcom,dpu-vig-qseed-off: offset of QSEED 
hardware
-                               -- qcom,dpu-vig-qseed-size: A u32 address range 
for qseed scaler.
-                               -- qcom,dpu-vig-pcc: offset and version of PCC 
hardware
-                               -- qcom,dpu-vig-hsic: offset and version of 
global PA adjustment
-                               -- qcom,dpu-vig-memcolor: offset and version of 
PA memcolor hardware
-- qcom,dpu-sspp-rgb-blocks:    A node that lists the blocks inside the RGB 
hardware. The
-                               block entries will contain the offset and 
version (if needed)
-                               of each feature block. The presence of a block 
entry
-                               indicates that the SSPP RGB contains that 
feature hardware.
-                               e.g. qcom,dpu-sspp-vig-blocks
-                               -- qcom,dpu-rgb-scaler-off: offset of RGB 
scaler hardware
-                               -- qcom,dpu-rgb-scaler-size: A u32 address 
range for scaler.
-                               -- qcom,dpu-rgb-pcc: offset and version of PCC 
hardware
-- qcom,dpu-dspp-blocks:                A node that lists the blocks inside the 
DSPP hardware. The
-                               block entries will contain the offset and 
version of each
-                               feature block. The presence of a block entry 
indicates that
-                               the DSPP contains that feature hardware.
-                               e.g. qcom,dpu-dspp-blocks
-                               -- qcom,dpu-dspp-pcc: offset and version of PCC 
hardware
-                               -- qcom,dpu-dspp-gc: offset and version of GC 
hardware
-                               -- qcom,dpu-dspp-igc: offset and version of IGC 
hardware
-                               -- qcom,dpu-dspp-hsic: offset and version of 
global PA adjustment
-                               -- qcom,dpu-dspp-memcolor: offset and version 
of PA memcolor hardware
-                               -- qcom,dpu-dspp-sixzone: offset and version of 
PA sixzone hardware
-                               -- qcom,dpu-dspp-gamut: offset and version of 
Gamut mapping hardware
-                               -- qcom,dpu-dspp-dither: offset and version of 
dither hardware
-                               -- qcom,dpu-dspp-hist: offset and version of 
histogram hardware
-                               -- qcom,dpu-dspp-vlut: offset and version of PA 
vLUT hardware
-- qcom,dpu-mixer-blocks:       A node that lists the blocks inside the layer 
mixer hardware. The
-                               block entries will contain the offset and 
version (if needed)
-                               of each feature block. The presence of a block 
entry
-                               indicates that the layer mixer contains that 
feature hardware.
-                               e.g. qcom,dpu-mixer-blocks
-                               -- qcom,dpu-mixer-gc: offset and version of 
mixer GC hardware
-- qcom,dpu-dspp-ad-off:                Array of u32 offsets indicate the ad 
block offset from the
-                               DSPP offset. Since AD hardware is represented 
as part of
-                               DSPP block, the AD offsets must be offset from 
the
-                               corresponding DSPP base.
-- qcom,dpu-dspp-ad-version     A u32 value indicating the version of the AD 
hardware
-- qcom,dpu-vbif-id:            Array of vbif ids corresponding to the
-                               offsets defined in property: qcom,dpu-vbif-off.
-- qcom,dpu-vbif-default-ot-rd-limit:   A u32 value indicates the default read 
OT limit
-- qcom,dpu-vbif-default-ot-wr-limit:   A u32 value indicates the default write 
OT limit
-- qcom,dpu-vbif-dynamic-ot-rd-limit:   A series of 2 cell property, with a 
format
-                               of (pps, OT limit), where pps is pixel per 
second and
-                               OT limit is the read limit to apply if the given
-                               pps is not exceeded.
-- qcom,dpu-vbif-dynamic-ot-wr-limit:   A series of 2 cell property, with a 
format
-                               of (pps, OT limit), where pps is pixel per 
second and
-                               OT limit is the write limit to apply if the 
given
-                               pps is not exceeded.
-- qcom,dpu-vbif-memtype-0:     Array of u32 vbif memory type settings, group 0
-- qcom,dpu-vbif-memtype-1:     Array of u32 vbif memory type settings, group 1
-- qcom,dpu-wb-id:              Array of writeback ids corresponding to the
-                               offsets defined in property: qcom,dpu-wb-off.
-- qcom,dpu-wb-clk-ctrl:                Array of 2 cell property describing clk 
control
-                               offsets for dynamic clock gating. 1st value
-                               in the array represents offset of the control
-                               register. 2nd value represents bit offset within
-                               control register. Number of offsets defined 
should
-                               match the number of offsets defined in
-                               property: qcom,dpu-wb-off
-- qcom,dpu-reg-dma-off:         Offset of the register dma hardware block from
-                               "regdma_phys" defined in reg property.
-- qcom,dpu-reg-dma-version:    Version of the reg dma hardware block.
-- qcom,dpu-reg-dma-trigger-off: Offset of the lut dma trigger reg from 
"mdp_phys"
-                               defined in reg property.
 - qcom,dpu-dram-channels:      This represents the number of channels in the
                                Bus memory controller.
 - qcom,dpu-num-nrt-paths:      Integer property represents the number of 
non-realtime
@@ -277,95 +46,6 @@ Optional properties:
                                for particular chipset.
                                These paths must be defined after rt-paths in
                                "qcom,msm-bus,vectors-KBps" vector request.
-- qcom,dpu-max-bw-low-kbps:    This value indicates the max bandwidth in Kbps
-                               that can be supported without underflow.
-                               This is a low bandwidth threshold which should
-                               be applied in most scenarios to be safe from
-                               underflows when unable to satisfy bandwidth
-                               requirements.
-- qcom,dpu-max-bw-high-kbps:   This value indicates the max bandwidth in Kbps
-                               that can be supported without underflow.
-                               This is a high bandwidth threshold which can be
-                               applied in scenarios where panel interface can
-                               be more tolerant to memory latency such as
-                               command mode panels.
-- qcom,dpu-core-ib-ff:         A string entry indicating the fudge factor for
-                               core ib calculation.
-- qcom,dpu-core-clk-ff:                A string entry indicating the fudge 
factor for
-                               core clock calculation.
-- qcom,dpu-min-core-ib-kbps:   This u32 value indicates the minimum mnoc ib
-                               vote in Kbps that can be reduced without 
hitting underflow.
-                               BW calculation logic will choose the IB 
bandwidth requirement
-                               based on usecase if this floor value is not 
defined.
-- qcom,dpu-min-llcc-ib-kbps:   This u32 value indicates the minimum llcc ib
-                               vote in Kbps that can be reduced without 
hitting underflow.
-                               BW calculation logic will choose the IB 
bandwidth requirement
-                               based on usecase if this floor value is not 
defined.
-- qcom,dpu-min-dram-ib-kbps:   This u32 value indicates the minimum dram ib
-                               vote in Kbps that can be reduced without 
hitting underflow.
-                               BW calculation logic will choose the IB 
bandwidth requirement
-                               based on usecase if this floor value is not 
defined.
-- qcom,dpu-comp-ratio-rt:      A string entry indicating the compression ratio
-                               for each supported compressed format on 
realtime interface.
-                               The string is composed of one or more of
-                               <fourcc code>/<vendor 
code>/<modifier>/<compression ratio>
-                               separated with spaces.
-- qcom,dpu-comp-ratio-nrt:     A string entry indicating the compression ratio
-                               for each supported compressed format on 
non-realtime interface.
-                               The string is composed of one or more of
-                               <fourcc code>/<vendor 
code>/<modifier>/<compression ratio>
-                               separated with spaces.
-- qcom,dpu-undersized-prefill-lines:   A u32 value indicates the size of 
undersized prefill in lines.
-- qcom,dpu-xtra-prefill-lines: A u32 value indicates the extra prefill in 
lines.
-- qcom,dpu-dest-scale-prefill-lines:   A u32 value indicates the latency of 
destination scaler in lines.
-- qcom,dpu-macrotile-prefill-lines:    A u32 value indicates the latency of 
macrotile in lines.
-- qcom,dpu-yuv-nv12-prefill-lines:     A u32 value indicates the latency of 
yuv/nv12 in lines.
-- qcom,dpu-linear-prefill-lines:       A u32 value indicates the latency of 
linear in lines.
-- qcom,dpu-downscaling-prefill-lines:  A u32 value indicates the latency of 
downscaling in lines.
-- qcom,dpu-max-per-pipe-bw-kbps:       Array of u32 value indicates the max 
per pipe bandwidth in Kbps.
-- qcom,dpu-amortizable-threshold:      This value indicates the min for 
traffic shaping in lines.
-- qcom,dpu-vbif-qos-rt-remap:  This array is used to program vbif qos remapper 
register
-                               priority for realtime clients.
-- qcom,dpu-vbif-qos-nrt-remap: This array is used to program vbif qos remapper 
register
-                               priority for non-realtime clients.
-- qcom,dpu-danger-lut:         A 4 cell property, with a format of <linear,
-                               tile, nrt, cwb>,
-                               indicating the danger luts on sspp.
-- qcom,dpu-safe-lut:           A 4 cell property, with a format of <linear,
-                               tile, nrt, cwb>,
-                               indicating the safe luts on sspp.
-- qcom,dpu-qos-lut-linear:     Array of 3 cell property, with a format of
-                               <fill level, lut hi, lut lo> in ascending fill 
level
-                               indicating the qos luts for linear format on 
sspp.
-                               Zero fill level on the last entry identifies 
the default lut.
-- qcom,dpu-qos-lut-macrotile:  Array of 3 cell property, with a format of
-                               <fill level, lut hi, lut lo> in ascending fill 
level
-                               indicating the qos luts for macrotile format on 
sspp.
-                               Zero fill level on the last entry identifies 
the default lut.
-- qcom,dpu-qos-lut-nrt:                Array of 3 cell property, with a format 
of
-                               <fill level, lut hi, lut lo> in ascending fill 
level
-                               indicating the qos luts for nrt (e.g wfd) on 
sspp.
-                               Zero fill level on the last entry identifies 
the default lut.
-- qcom,dpu-qos-lut-cwb:                Array of 3 cell property, with a format 
of
-                               <fill level, lut hi, lut lo> in ascending fill 
level
-                               indicating the qos luts for cwb on sspp.
-                               Zero fill level on the last entry identifies 
the default lut.
-- qcom,dpu-cdp-setting:                Array of 2 cell property, with a format 
of
-                               <read enable, write enable> for cdp use cases in
-                               order of <real_time>, and <non_real_time>.
-- qcom,dpu-inline-rot-xin:     An integer array of xin-ids related to inline
-                               rotation.
-- qcom,dpu-inline-rot-xin-type:        A string array indicating the type of 
xin,
-                               namely sspp or wb. Number of entries should 
match
-                               the number of xin-ids defined in
-                               property: qcom,dpu-inline-rot-xin
-- qcom,dpu-inline-rot-clk-ctrl:        Array of offsets describing clk control
-                               offsets for dynamic clock gating. 1st value
-                               in the array represents offset of the control
-                               register. 2nd value represents bit offset within
-                               control register. Number of offsets defined 
should
-                               match the number of xin-ids defined in
-                               property: qcom,dpu-inline-rot-xin
 
 Bus Scaling Subnodes:
 - qcom,dpu-reg-bus:            Property to provide Bus scaling for register 
access for
@@ -447,223 +127,13 @@ Example:
     #interrupt-cells = <1>;
     iommus = <&mdp_smmu 0>;
 
-    qcom,dpu-off = <0x1000>;
-    qcom,dpu-ctl-off = <0x00002000 0x00002200 0x00002400
-                    0x00002600 0x00002800>;
-    qcom,dpu-mixer-off = <0x00045000 0x00046000
-                       0x00047000 0x0004a000>;
-    qcom,dpu-dspp-top-off = <0x1300>;
-    qcom,dpu-dspp-off = <0x00055000 0x00057000>;
-    qcom,dpu-dspp-ad-off = <0x24000 0x22800>;
-    qcom,dpu-dspp-ad-version = <0x00030000>;
-    qcom,dpu-dest-scaler-top-off = <0x00061000>;
-    qcom,dpu-dest-scaler-off = <0x800 0x1000>;
-    qcom,dpu-wb-off = <0x00066000>;
-    qcom,dpu-wb-xin-id = <6>;
-    qcom,dpu-intf-off = <0x0006b000 0x0006b800
-                       0x0006c000 0x0006c800>;
-    qcom,dpu-intf-type = "none", "dsi", "dsi", "hdmi";
-    qcom,dpu-pp-off = <0x00071000 0x00071800
-                         0x00072000 0x00072800>;
-    qcom,dpu-pp-slave = <0x0 0x0 0x0 0x0>;
-    qcom,dpu-cdm-off = <0x0007a200>;
-    qcom,dpu-dsc-off = <0x00081000 0x00081400>;
-    qcom,dpu-intf-max-prefetch-lines = <0x15 0x15 0x15 0x15>;
-
-    qcom,dpu-mixer-pair-mask = <2 1 6 0 0 3>;
-    qcom,dpu-mixer-blend-op-off = <0x20 0x38 0x50 0x68 0x80 0x98
-                                   0xb0 0xc8 0xe0 0xf8 0x110>;
-
-
-    qcom,dpu-sspp-type = "vig", "vig", "vig",
-                             "vig", "rgb", "rgb",
-                             "rgb", "rgb", "dma",
-                             "dma", "cursor", "cursor";
-
-    qcom,dpu-sspp-off = <0x00005000 0x00007000 0x00009000
-                     0x0000b000 0x00015000 0x00017000
-                     0x00019000 0x0001b000 0x00025000
-                     0x00027000 0x00035000 0x00037000>;
-
-    qcom,dpu-sspp-xin-id = <0 4 8
-                       12 1 5
-                       9 13 2
-                       10 7 7>;
-
-    /* offsets are relative to "mdp_phys + qcom,dpu-off */
-    qcom,dpu-sspp-clk-ctrl = <0x2ac 0>, <0x2b4 0>, <0x2bc 0>,
-                         <0x2c4 0>, <0x2ac 4>, <0x2b4 4>, <0x2bc 4>,
-                         <0x2c4 4>, <0x2ac 8>, <0x2b4 8>, <0x3a8 16>,
-                         <0x3b0 16>;
-    qcom,dpu-sspp-clk-status = <0x2ac 0>, <0x2b4 0>, <0x2bc 0>,
-                         <0x2c4 0>, <0x2ac 4>, <0x2b4 4>, <0x2bc 4>,
-                         <0x2c4 4>, <0x2ac 8>, <0x2b4 8>, <0x3a8 16>,
-                         <0x3b0 16>;
-    qcom,dpu-mixer-linewidth = <2560>;
-    qcom,dpu-sspp-linewidth = <2560>;
-    qcom,dpu-mixer-blendstages = <0x7>;
-    qcom,dpu-highest-bank-bit = <0x2>;
-    qcom,dpu-ubwc-version = <0x100>;
-    qcom,dpu-ubwc-static = <0x100>;
-    qcom,dpu-ubwc-swizzle = <0>;
-    qcom,dpu-panic-per-pipe;
-    qcom,dpu-has-src-split;
-    qcom,dpu-has-dim-layer;
-    qcom,dpu-sspp-src-size = <0x100>;
-    qcom,dpu-mixer-size = <0x100>;
-    qcom,dpu-ctl-size = <0x100>;
-    qcom,dpu-dspp-top-size = <0xc>;
-    qcom,dpu-dspp-size = <0x100>;
-    qcom,dpu-intf-size = <0x100>;
-    qcom,dpu-dsc-size = <0x100>;
-    qcom,dpu-cdm-size = <0x100>;
-    qcom,dpu-pp-size = <0x100>;
-    qcom,dpu-wb-size = <0x100>;
-    qcom,dpu-dest-scaler-top-size = <0xc>;
-    qcom,dpu-dest-scaler-size = <0x800>;
-    qcom,dpu-len = <0x100>;
-    qcom,dpu-wb-linewidth = <2560>;
-    qcom,dpu-sspp-scale-size = <0x100>;
-    qcom,dpu-mixer-blendstages = <0x8>;
-    qcom,dpu-qseed-type = "qseedv2";
-    qcom,dpu-csc-type = "csc-10bit";
-    qcom,dpu-highest-bank-bit = <15>;
-    qcom,dpu-has-mixer-gc;
-    qcom,dpu-has-idle-pc;
-    qcom,dpu-has-dest-scaler;
-    qcom,dpu-max-dest-scaler-input-linewidth = <2048>;
-    qcom,dpu-max-dest-scaler-output-linewidth = <2560>;
-    qcom,dpu-sspp-max-rects = <1 1 1 1
-                               1 1 1 1
-                               1 1
-                               1 1>;
-    qcom,dpu-sspp-excl-rect = <1 1 1 1
-                               1 1 1 1
-                               1 1
-                               1 1>;
-    qcom,dpu-sspp-smart-dma-priority = <0 0 0 0
-                                       0 0 0 0
-                                       0 0
-                                       1 2>;
-    qcom,dpu-smart-dma-rev = "smart_dma_v2";
-    qcom,dpu-te-off = <0x100>;
-    qcom,dpu-te2-off = <0x100>;
-    qcom,dpu-te-size = <0xffff>;
-    qcom,dpu-te2-size = <0xffff>;
-
-    qcom,dpu-wb-id = <2>;
-    qcom,dpu-wb-clk-ctrl = <0x2bc 16>;
-
-    qcom,dpu-danger-lut = <0x0000000f 0x0000ffff 0x00000000
-            0x00000000>;
-    qcom,dpu-safe-lut = <0xfffc 0xff00 0xffff 0xffff>;
-    qcom,dpu-qos-lut-linear =
-            <4 0x00000000 0x00000357>,
-            <5 0x00000000 0x00003357>,
-            <6 0x00000000 0x00023357>,
-            <7 0x00000000 0x00223357>,
-            <8 0x00000000 0x02223357>,
-            <9 0x00000000 0x22223357>,
-            <10 0x00000002 0x22223357>,
-            <11 0x00000022 0x22223357>,
-            <12 0x00000222 0x22223357>,
-            <13 0x00002222 0x22223357>,
-            <14 0x00012222 0x22223357>,
-            <0 0x00112222 0x22223357>;
-    qcom,dpu-qos-lut-macrotile =
-            <10 0x00000003 0x44556677>,
-            <11 0x00000033 0x44556677>,
-            <12 0x00000233 0x44556677>,
-            <13 0x00002233 0x44556677>,
-            <14 0x00012233 0x44556677>,
-            <0 0x00112233 0x44556677>;
-    qcom,dpu-qos-lut-nrt =
-            <0 0x00000000 0x00000000>;
-    qcom,dpu-qos-lut-cwb =
-            <0 0x75300000 0x00000000>;
-
-    qcom,dpu-cdp-setting = <1 1>, <1 0>;
-
-    qcom,dpu-vbif-off = <0 0>;
-    qcom,dpu-vbif-id = <0 1>;
-    qcom,dpu-vbif-default-ot-rd-limit = <32>;
-    qcom,dpu-vbif-default-ot-wr-limit = <16>;
-    qcom,dpu-vbif-dynamic-ot-rd-limit = <62208000 2>,
-        <124416000 4>, <248832000 16>;
-    qcom,dpu-vbif-dynamic-ot-wr-limit = <62208000 2>,
-        <124416000 4>, <248832000 16>;
-    qcom,dpu-vbif-memtype-0 = <3 3 3 3 3 3 3 3>;
-    qcom,dpu-vbif-memtype-1 = <3 3 3 3 3 3>;
-
     qcom,dpu-dram-channels = <2>;
     qcom,dpu-num-nrt-paths = <1>;
 
-    qcom,dpu-max-bw-high-kbps = <9000000>;
-    qcom,dpu-max-bw-low-kbps = <9000000>;
-
-    qcom,dpu-core-ib-ff = "1.1";
-    qcom,dpu-core-clk-ff = "1.0";
-    qcom,dpu-min-core-ib-kbps = <2400000>;
-    qcom,dpu-min-llcc-ib-kbps = <800000>;
-    qcom,dpu-min-dram-ib-kbps = <800000>;
-    qcom,dpu-comp-ratio-rt = "NV12/5/1/1.1 AB24/5/1/1.2 XB24/5/1/1.3";
-    qcom,dpu-comp-ratio-nrt = "NV12/5/1/1.1 AB24/5/1/1.2 XB24/5/1/1.3";
-    qcom,dpu-undersized-prefill-lines = <4>;
-    qcom,dpu-xtra-prefill-lines = <5>;
-    qcom,dpu-dest-scale-prefill-lines = <6>;
-    qcom,dpu-macrotile-prefill-lines = <7>;
-    qcom,dpu-yuv-nv12-prefill-lines = <8>;
-    qcom,dpu-linear-prefill-lines = <9>;
-    qcom,dpu-downscaling-prefill-lines = <10>;
-    qcom,dpu-max-per-pipe-bw-kbps = <2400000 2400000 2400000 2400000
-        2400000 2400000 2400000 2400000>;
-    qcom,dpu-amortizable-threshold = <11>;
-
-    qcom,dpu-vbif-qos-rt-remap = <3 3 4 4 5 5 6 6>;
-    qcom,dpu-vbif-qos-nrt-remap = <3 3 3 3 3 3 3 3>;
-
-    qcom,dpu-sspp-vig-blocks {
-        qcom,dpu-vig-csc-off = <0x320>;
-        qcom,dpu-vig-qseed-off = <0x200>;
-        qcom,dpu-vig-qseed-size = <0x74>;
-        /* Offset from vig top, version of HSIC */
-        qcom,dpu-vig-hsic = <0x200 0x00010000>;
-        qcom,dpu-vig-memcolor = <0x200 0x00010000>;
-        qcom,dpu-vig-pcc = <0x1780 0x00010000>;
-    };
-
-    qcom,dpu-sspp-rgb-blocks {
-        qcom,dpu-rgb-scaler-off = <0x200>;
-        qcom,dpu-rgb-scaler-size = <0x74>;
-        qcom,dpu-rgb-pcc = <0x380 0x00010000>;
-    };
-
-    qcom,dpu-dspp-blocks {
-        qcom,dpu-dspp-igc = <0x0 0x00010000>;
-        qcom,dpu-dspp-pcc = <0x1700 0x00010000>;
-        qcom,dpu-dspp-gc = <0x17c0 0x00010000>;
-        qcom,dpu-dspp-hsic = <0x0 0x00010000>;
-        qcom,dpu-dspp-memcolor = <0x0 0x00010000>;
-        qcom,dpu-dspp-sixzone = <0x0 0x00010000>;
-        qcom,dpu-dspp-gamut = <0x1600 0x00010000>;
-        qcom,dpu-dspp-dither = <0x0 0x00010000>;
-        qcom,dpu-dspp-hist = <0x0 0x00010000>;
-        qcom,dpu-dspp-vlut = <0x0 0x00010000>;
-    };
-
-    qcom,dpu-mixer-blocks {
-        qcom,dpu-mixer-gc = <0x3c0 0x00010000>;
-    };
-
     qcom,msm-hdmi-audio-rx {
         compatible = "qcom,msm-hdmi-audio-codec-rx";
     };
 
-    qcom,dpu-inline-rotator = <&mdss_rotator 0>;
-    qcom,dpu-inline-rot-xin = <10 11>;
-    qcom,dpu-inline-rot-xin-type = "sspp", "wb";
-    qcom,dpu-inline-rot-clk-ctrl = <0x2bc 0x8>, <0x2bc 0xc>;
-
     qcom,platform-supply-entries {
        #address-cells = <1>;
        #size-cells = <0>;
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Reply via email to