On 08/19/2018 12:36 PM, Ville Syrjälä wrote:
> On Fri, Aug 17, 2018 at 03:19:37PM -0400, Mikulas Patocka wrote:
>> On Sun Ultra 5, it happens that the dot clock is not set up properly for
>> some videomodes. For example, if we set the videomode "r1024x768x60" in
>> the firmware, Linux would incorrectly set a videomode with refresh rate
>> 180Hz when booting (suprisingly, my LCD monitor can display it, although
>> display quality is very low).
>>
>> The reason is this: Older mach64 cards set the divider in the register
>> VCLK_POST_DIV. The register has four 2-bit fields (the field that is
>> actually used is specified in the lowest two bits of the register
>> CLOCK_CNTL). The 2 bits select divider "1, 2, 4, 8". On newer mach64 cards,
>> there's another bit added - the top four bits of PLL_EXT_CNTL extend the
>> divider selection, so we have possible dividers "1, 2, 4, 8, 3, 5, 6, 12".
>> The Linux driver clears the top four bits of PLL_EXT_CNTL and never sets
>> them, so it can work regardless if the card supports them. However, the
>> sparc64 firmware may set these extended dividers during boot - and the
>> mach64 driver detects incorrect dot clock in this case.
>>
>> This patch makes the driver read the additional divider bit from
>> PLL_EXT_CNTL and calculate the initial refresh rate properly.
>>
>> Signed-off-by: Mikulas Patocka <mpato...@redhat.com>
>> Cc: sta...@vger.kernel.org
>>
>> ---
>> drivers/video/fbdev/aty/atyfb.h | 3 ++-
>> drivers/video/fbdev/aty/atyfb_base.c | 7 ++++---
>> drivers/video/fbdev/aty/mach64_ct.c | 10 +++++-----
>> 3 files changed, 11 insertions(+), 9 deletions(-)
>>
>> Index: linux-stable/drivers/video/fbdev/aty/atyfb.h
>> ===================================================================
>> --- linux-stable.orig/drivers/video/fbdev/aty/atyfb.h 2018-08-13
>> 21:12:11.000000000 +0200
>> +++ linux-stable/drivers/video/fbdev/aty/atyfb.h 2018-08-13
>> 21:17:14.000000000 +0200
>> @@ -333,6 +333,8 @@ extern const struct aty_pll_ops aty_pll_
>> extern void aty_set_pll_ct(const struct fb_info *info, const union aty_pll
>> *pll);
>> extern u8 aty_ld_pll_ct(int offset, const struct atyfb_par *par);
>>
>> +extern const u8 aty_postdividers[8];
>> +
>>
>> /*
>> * Hardware cursor support
>> @@ -359,7 +361,6 @@ static inline void wait_for_idle(struct
>>
>> extern void aty_reset_engine(const struct atyfb_par *par);
>> extern void aty_init_engine(struct atyfb_par *par, struct fb_info *info);
>> -extern u8 aty_ld_pll_ct(int offset, const struct atyfb_par *par);
>>
>> void atyfb_copyarea(struct fb_info *info, const struct fb_copyarea *area);
>> void atyfb_fillrect(struct fb_info *info, const struct fb_fillrect *rect);
>> Index: linux-stable/drivers/video/fbdev/aty/atyfb_base.c
>> ===================================================================
>> --- linux-stable.orig/drivers/video/fbdev/aty/atyfb_base.c 2018-08-13
>> 21:12:11.000000000 +0200
>> +++ linux-stable/drivers/video/fbdev/aty/atyfb_base.c 2018-08-13
>> 21:22:23.000000000 +0200
>> @@ -3087,17 +3087,18 @@ static int atyfb_setup_sparc(struct pci_
>> /*
>> * PLL Reference Divider M:
>> */
>> - M = pll_regs[2];
>> + M = pll_regs[PLL_REF_DIV];
>>
>> /*
>> * PLL Feedback Divider N (Dependent on CLOCK_CNTL):
>> */
>> - N = pll_regs[7 + (clock_cntl & 3)];
>> + N = pll_regs[VCLK0_FB_DIV + (clock_cntl & 3)];
>>
>> /*
>> * PLL Post Divider P (Dependent on CLOCK_CNTL):
>> */
>> - P = 1 << (pll_regs[6] >> ((clock_cntl & 3) << 1));
>> + P = aty_postdividers[((pll_regs[VCLK_POST_DIV] >> ((clock_cntl
>> & 3) << 1)) & 3) |
>> + ((pll_regs[PLL_EXT_CNTL] >> (2 +
>> (clock_cntl & 3))) & 4)];
>>
>> /*
>> * PLL Divider Q:
>> Index: linux-stable/drivers/video/fbdev/aty/mach64_ct.c
>> ===================================================================
>> --- linux-stable.orig/drivers/video/fbdev/aty/mach64_ct.c 2018-08-13
>> 21:12:11.000000000 +0200
>> +++ linux-stable/drivers/video/fbdev/aty/mach64_ct.c 2018-08-13
>> 21:35:32.000000000 +0200
>> @@ -115,7 +115,7 @@ static void aty_st_pll_ct(int offset, u8
>> */
>>
>> #define Maximum_DSP_PRECISION 7
>> -static u8 postdividers[] = {1,2,4,8,3};
>> +const u8 aty_postdividers[8] = {1,2,4,8,3,5,6,12};
>
> Not sure about the '5'. That setting is marked as reserved in my docs.
> So I guess it doesn't really matter what number we put there.
>
> Reviewed-by: Ville Syrjälä <syrj...@sci.fi>
Patch queued for 4.20, thanks.
Best regards,
--
Bartlomiej Zolnierkiewicz
Samsung R&D Institute Poland
Samsung Electronics
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
