Hi Icenowy,
On Thursday, 18 October 2018 13:00:05 EEST Icenowy Zheng wrote:
> 在 2018-10-18四的 11:53 +0300，Laurent Pinchart写道：
> > On Thursday, 18 October 2018 10:33:22 EEST Icenowy Zheng wrote:
> >> The ANX6345 is an ultra-low power DisplayPort/eDP transmitter
> >> designed
> >> for portable devices.
> >>
> >> Add a binding document for it.
> >>
> >> Signed-off-by: Icenowy Zheng <[email protected]>
> >> ---
> >>
> >> .../bindings/display/bridge/anx6345.txt | 39 +++++++++++++++++++
> >>
> >> 1 file changed, 39 insertions(+)
> >> create mode 100644
> >>
> >> Documentation/devicetree/bindings/display/bridge/anx6345.txt
> >>
> >> diff --git
> >> a/Documentation/devicetree/bindings/display/bridge/anx6345.txt
> >> b/Documentation/devicetree/bindings/display/bridge/anx6345.txt new
> >> file
> >> mode 100644
> >> index 000000000000..0689d4eb5f65
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/display/bridge/anx6345.txt
> >> @@ -0,0 +1,39 @@
> >> +Analogix ANX6345 eDP Transmitter
> >> +--------------------------------
> >> +
> >> +The ANX6345 is an ultra-low power Full-HD eDP transmitter designed
> >> for
> >> +portable devices.
> >> +
> >> +Required properties:
> >> +
> >> + - compatible : "analogix,anx6345"
> >> + - reg : I2C address of the device
> >> + - reset-gpios : Which GPIO to use for reset
> >> +
> >> +Optional properties:
> >> +
> >> + - dvdd12-supply : Regulator for 1.2V digital core power.
> >> + - dvdd25-supply : Regulator for 2.5V digital core power.
> >
> > Shouldn't these to supplies be mandatory ?
>
> Yes they should.
>
> >> + - panel-supply : Regulator for the power of the panel.
> >
> > Shouldn't the panel supply for specified in the DT node of the panel
> > ?
>
> However, eDP panel can be probed, may vary on the same device, and we
> don't have a generic binding for it...
Shouldn't we fix that ? :-)
> >> + - edid : verbatim EDID data block describing
> >> attached
> >> + panel, only used when the panel has no EDID
> >> info.
> >
> > This should also be specified in the panel DT node.
> >
> > > + - Video port for RGB input, using the DT bindings defined in [1].
> >
> > I think you should also add a port for the output.
>
> What will it point to?
The panel DT node ?
> >> +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
> >> +
> >> +Example:
> >> +
> >> +anx6345: anx6345@38 {
> >> + compatible = "analogix,anx6345";
> >> + reg = <0x38>;
> >> + reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
> >> + panel-supply = <®_dc1sw>;
> >> + dvdd25-supply = <®_dldo2>;
> >> + dvdd12-supply = <®_fldo1>;
> >> +
> >> + port {
> >> + anx6345_in: endpoint {
> >> + remote-endpoint = <&tcon0_out_anx6345>;
> >> + };
> >> + };
> >> +};
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
