On 2019-08-29 13:30, Robert Chiras wrote:
> Some of the registers, like LCDC_CTRL, CTRL2_OUTSTANDING_REQS and
> CTRL1_RECOVERY_ON_UNDERFLOW needs to be properly cleared/initialized
> for a better start and stop routine.
This patch uses CTRL2_OUTSTANDING_REQS which is only introduced in the
next patch. This breaks bisectability.
--
Stefan
>
> Signed-off-by: Robert Chiras <robert.chi...@nxp.com>
> Tested-by: Guido Günther <a...@sigxcpu.org>
> ---
> drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 12 ++++++++++++
> 1 file changed, 12 insertions(+)
>
> diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
> b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
> index b69ace8..5e44f57 100644
> --- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
> +++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
> @@ -127,6 +127,10 @@ static void mxsfb_enable_controller(struct
> mxsfb_drm_private *mxsfb)
> clk_prepare_enable(mxsfb->clk_disp_axi);
> clk_prepare_enable(mxsfb->clk);
>
> + if (mxsfb->devdata->ipversion >= 4)
> + writel(CTRL2_OUTSTANDING_REQS(REQ_16),
> + mxsfb->base + LCDC_V4_CTRL2 + REG_SET);
> +
> /* If it was disabled, re-enable the mode again */
> writel(CTRL_DOTCLK_MODE, mxsfb->base + LCDC_CTRL + REG_SET);
>
> @@ -136,12 +140,19 @@ static void mxsfb_enable_controller(struct
> mxsfb_drm_private *mxsfb)
> writel(reg, mxsfb->base + LCDC_VDCTRL4);
>
> writel(CTRL_RUN, mxsfb->base + LCDC_CTRL + REG_SET);
> + writel(CTRL1_RECOVERY_ON_UNDERFLOW, mxsfb->base + LCDC_CTRL1 + REG_SET);
> }
>
> static void mxsfb_disable_controller(struct mxsfb_drm_private *mxsfb)
> {
> u32 reg;
>
> + if (mxsfb->devdata->ipversion >= 4)
> + writel(CTRL2_OUTSTANDING_REQS(0x7),
> + mxsfb->base + LCDC_V4_CTRL2 + REG_CLR);
> +
> + writel(CTRL_RUN, mxsfb->base + LCDC_CTRL + REG_CLR);
> +
> /*
> * Even if we disable the controller here, it will still continue
> * until its FIFOs are running out of data
> @@ -295,6 +306,7 @@ void mxsfb_crtc_enable(struct mxsfb_drm_private *mxsfb)
> dma_addr_t paddr;
>
> mxsfb_enable_axi_clk(mxsfb);
> + writel(0, mxsfb->base + LCDC_CTRL);
> mxsfb_crtc_mode_set_nofb(mxsfb);
>
> /* Write cur_buf as well to avoid an initial corrupt frame */
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
