Hi Vasily,
Thank you for the patch.
On Thu, Feb 20, 2020 at 12:35:08AM -0800, Vasily Khoruzhick wrote:
> From: Icenowy Zheng <icen...@aosc.io>
>
> Pinebook has an ANX6345 bridge connected to the RGB666 LCD output and
> eDP panel input. The bridge is controlled via I2C that's connected to
> R_I2C bus.
>
> Enable all this hardware in device tree.
>
> Signed-off-by: Icenowy Zheng <icen...@aosc.io>
> Signed-off-by: Vasily Khoruzhick <anars...@gmail.com>
> ---
> .../dts/allwinner/sun50i-a64-pinebook.dts | 69 ++++++++++++++++++-
> 1 file changed, 68 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
> b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
> index c06c540e6c08..f5633f550d8a 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
> @@ -48,6 +48,18 @@ lid_switch {
> };
> };
>
> + panel_edp: panel-edp {
> + compatible = "neweast,wjfh116008a";
> + backlight = <&backlight>;
> + power-supply = <®_dc1sw>;
> +
> + port {
> + panel_edp_in: endpoint {
> + remote-endpoint = <&anx6345_out_edp>;
> + };
> + };
> + };
> +
> reg_vbklt: vbklt {
> compatible = "regulator-fixed";
> regulator-name = "vbklt";
> @@ -109,6 +121,10 @@ &dai {
> status = "okay";
> };
>
> +&de {
> + status = "okay";
> +};
> +
> &ehci0 {
> phys = <&usbphy 0>;
> phy-names = "usb";
> @@ -119,6 +135,10 @@ &ehci1 {
> status = "okay";
> };
>
> +&mixer0 {
> + status = "okay";
> +};
> +
> &mmc0 {
> pinctrl-names = "default";
> pinctrl-0 = <&mmc0_pins>;
> @@ -177,12 +197,45 @@ &pwm {
> status = "okay";
> };
>
> -/* The ANX6345 eDP-bridge is on r_i2c */
> &r_i2c {
> clock-frequency = <100000>;
> pinctrl-names = "default";
> pinctrl-0 = <&r_i2c_pl89_pins>;
> status = "okay";
> +
> + anx6345: anx6345@38 {
> + compatible = "analogix,anx6345";
> + reg = <0x38>;
> + reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */
> + dvdd25-supply = <®_dldo2>;
> + dvdd12-supply = <®_fldo1>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + anx6345_in: port@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> + anx6345_in_tcon0: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&tcon0_out_anx6345>;
> + };
As there's a single endpoint, you can drop the reg property, the @0
suffix, and the #address-cells and #size-cells property in the port@0
node (but not in the ports node).
> + };
> +
> + anx6345_out: port@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + anx6345_out_edp: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&panel_edp_in>;
> + };
Same here.
Reviewed-by: Laurent Pinchart <laurent.pinch...@ideasonboard.com>
> + };
> + };
> + };
> };
>
> &r_pio {
> @@ -357,6 +410,20 @@ &sound {
> "MIC2", "Internal Microphone Right";
> };
>
> +&tcon0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&lcd_rgb666_pins>;
> +
> + status = "okay";
> +};
> +
> +&tcon0_out {
> + tcon0_out_anx6345: endpoint@0 {
> + reg = <0>;
> + remote-endpoint = <&anx6345_in_tcon0>;
> + };
> +};
> +
> &uart0 {
> pinctrl-names = "default";
> pinctrl-0 = <&uart0_pb_pins>;
--
Regards,
Laurent Pinchart
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
