On Fri, 29 Apr 2022 at 22:56, Marek Vasut <ma...@denx.de> wrote:
>
> Implement DSI-to-e(DP) mode, which is a mix of currently supported
> DSI-to-DPI and DPI-to-(e)DP modes. The input side is configured as
> either DSI or DPI, the DP AUX channel is registered for both input
> side options, and the DSI host is attached for both DPI and (e)DP
> output side options.
>
> One notable detail is that the DSI-to-(e)DP mode requires the Pixel
> PLL to be always enabled, which is not needed for DPI-to-(e)DP mode
> which gets the matching clock direct from DPI Pixel Clock instead.
>
> Signed-off-by: Marek Vasut <ma...@denx.de>
> Cc: Jonas Karlman <jo...@kwiboo.se>
> Cc: Laurent Pinchart <laurent.pinch...@ideasonboard.com>
> Cc: Lucas Stach <l.st...@pengutronix.de>
> Cc: Marek Vasut <ma...@denx.de>
> Cc: Maxime Ripard <max...@cerno.tech>
> Cc: Neil Armstrong <narmstr...@baylibre.com>
> Cc: Robert Foss <robert.f...@linaro.org>
> Cc: Sam Ravnborg <s...@ravnborg.org>
> ---
> drivers/gpu/drm/bridge/tc358767.c | 40 +++++++++++++++++++++++--------
> 1 file changed, 30 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/tc358767.c
> b/drivers/gpu/drm/bridge/tc358767.c
> index e72dd5cd9700..798da0e4d086 100644
> --- a/drivers/gpu/drm/bridge/tc358767.c
> +++ b/drivers/gpu/drm/bridge/tc358767.c
> @@ -309,6 +309,9 @@ struct tc_data {
> /* do we have IRQ */
> bool have_irq;
>
> + /* Input connector type, DSI and not DPI. */
> + bool input_connector_dsi;
> +
> /* HPD pin number (0 or 1) or -ENODEV */
> int hpd_pin;
> };
> @@ -1353,8 +1356,18 @@ static int tc_edp_stream_enable(struct tc_data *tc)
>
> dev_dbg(tc->dev, "enable video stream\n");
>
> - /* PXL PLL setup */
> - if (tc_test_pattern) {
> + /*
> + * Pixel PLL must be enabled for DSI input mode and test pattern.
> + *
> + * Per TC9595XBG datasheet Revision 0.1 2018-12-27 Figure 4.18
> + * "Clock Mode Selection and Clock Sources", either Pixel PLL
> + * or DPI_PCLK supplies StrmClk. DPI_PCLK is only available in
> + * case valid Pixel Clock are supplied to the chip DPI input.
> + * In case built-in test pattern is desired OR DSI input mode
> + * is used, DPI_PCLK is not available and thus Pixel PLL must
> + * be used instead.
> + */
> + if (tc->input_connector_dsi || tc_test_pattern) {
> ret = tc_pxl_pll_en(tc, clk_get_rate(tc->refclk),
> 1000 * tc->mode.clock);
> if (ret)
> @@ -1394,7 +1407,10 @@ static int tc_edp_stream_enable(struct tc_data *tc)
> return ret;
>
> /* Set input interface */
> - return tc_dpi_rx_enable(tc);
> + if (tc->input_connector_dsi)
> + return tc_dsi_rx_enable(tc);
> + else
> + return tc_dpi_rx_enable(tc);
> }
>
> static int tc_edp_stream_disable(struct tc_data *tc)
> @@ -2004,14 +2020,18 @@ static int tc_probe_bridge_endpoint(struct tc_data
> *tc)
> mode |= BIT(endpoint.port);
> }
>
> - if (mode == mode_dpi_to_edp || mode == mode_dpi_to_dp)
> + if (mode == mode_dpi_to_edp || mode == mode_dpi_to_dp) {
> + tc->input_connector_dsi = false;
> return tc_probe_edp_bridge_endpoint(tc);
> - else if (mode == mode_dsi_to_dpi)
> + } else if (mode == mode_dsi_to_dpi) {
> + tc->input_connector_dsi = true;
> return tc_probe_dpi_bridge_endpoint(tc);
> - else if (mode == mode_dsi_to_edp || mode == mode_dsi_to_dp)
> - dev_warn(dev, "The mode DSI-to-(e)DP is not supported!\n");
> - else
> - dev_warn(dev, "Invalid mode (0x%x) is not supported!\n",
> mode);
> + } else if (mode == mode_dsi_to_edp || mode == mode_dsi_to_dp) {
> + tc->input_connector_dsi = true;
> + return tc_probe_edp_bridge_endpoint(tc);
> + }
> +
> + dev_warn(dev, "Invalid mode (0x%x) is not supported!\n", mode);
>
> return -EINVAL;
> }
> @@ -2149,7 +2169,7 @@ static int tc_probe(struct i2c_client *client, const
> struct i2c_device_id *id)
>
> i2c_set_clientdata(client, tc);
>
> - if (tc->bridge.type == DRM_MODE_CONNECTOR_DPI) { /* DPI output */
> + if (tc->input_connector_dsi) { /* DSI input */
> ret = tc_mipi_dsi_host_attach(tc);
> if (ret) {
> drm_bridge_remove(&tc->bridge);
Reviewed-by: Robert Foss <robert.f...@linaro.org>
