On 10/02/2023 12:34, Neil Armstrong wrote:
Add the Display Port controller subnode to the MDSS node.
Signed-off-by: Neil Armstrong <neil.armstr...@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8350.dtsi | 82 +++++++++++++++++++++++++++++++++++-
1 file changed, 80 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi
b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index d490ce84a022..eb636b7dffa7 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -2862,13 +2862,20 @@ ports {
port@0 {
reg = <0>;
- dpu_intf1_out: endpoint {
- remote-endpoint =
<&mdss_dsi0_in>;
+ dpu_intf0_out: endpoint {
+ remote-endpoint =
<&mdss_dp_in>;
No need to reorder these ports. Please add DP to the end.
};
};
port@1 {
reg = <1>;
+ dpu_intf1_out: endpoint {
+ remote-endpoint =
<&mdss_dsi0_in>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
dpu_intf2_out: endpoint {
remote-endpoint =
<&mdss_dsi1_in>;
};
@@ -2876,6 +2883,77 @@ dpu_intf2_out: endpoint {
};
};
+ mdss_dp: displayport-controller@ae90000 {
+ compatible = "qcom,sm8350-dp";
+ reg = <0 0xae90000 0 0x200>,
+ <0 0xae90200 0 0x200>,
+ <0 0xae90400 0 0x600>,
+ <0 0xae91000 0 0x400>;
This will not validate against the schema. Please add p1 region at the
end (I assume it is <0 0x0ae91400 0 0x400>).
+ interrupt-parent = <&mdss>;
+ interrupts = <12>;
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
+ <&dispcc
DISP_CC_MDSS_DP_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
+ clock-names = "core_iface",
+ "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface",
+ "stream_pixel";
+
+ assigned-clocks = <&dispcc
DISP_CC_MDSS_DP_LINK_CLK_SRC>,
+ <&dispcc
DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
+ assigned-clock-parents = <&usb_1_qmpphy 1>,
+ <&usb_1_qmpphy 2>;
Please use defined names here and in the phys below
+
+ phys = <&usb_1_qmpphy 1>;
+ phy-names = "dp";
+
+ #sound-dai-cells = <0>;
+
+ operating-points-v2 = <&dp_opp_table>;
+ power-domains = <&rpmhpd SM8350_MMCX>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss_dp_in: endpoint {
+ remote-endpoint =
<&dpu_intf0_out>;
+ };
+ };
+ };
+
+ dp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps =
<&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps =
<&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps =
<&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps =
<&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
mdss_dsi0: dsi@ae94000 {
compatible = "qcom,sm8350-dsi-ctrl",
"qcom,mdss-dsi-ctrl";
reg = <0 0x0ae94000 0 0x400>;
--
With best wishes
Dmitry
