On 29/05/2023 15:10, Konrad Dybcio wrote:


On 29.05.2023 11:44, Luca Weiss wrote:
Add the nodes that describe the mdss so that display can work on
MSM8226.

Signed-off-by: Luca Weiss <l...@z3ntu.xyz>
---
  arch/arm/boot/dts/qcom-msm8226.dtsi | 118 ++++++++++++++++++++++++++++++++++++
  1 file changed, 118 insertions(+)

diff --git a/arch/arm/boot/dts/qcom-msm8226.dtsi 
b/arch/arm/boot/dts/qcom-msm8226.dtsi
index 42acb9ddb8cc..182d6405032f 100644
--- a/arch/arm/boot/dts/qcom-msm8226.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8226.dtsi
@@ -636,6 +636,124 @@ smd-edge {
                                label = "lpass";
                        };
                };
+
+               mdss: display-subsystem@fd900000 {
+                       compatible = "qcom,mdss";
+                       reg = <0xfd900000 0x100>, <0xfd924000 0x1000>;
+                       reg-names = "mdss_phys", "vbif_phys";
+
+                       power-domains = <&mmcc MDSS_GDSC>;
+
+                       clocks = <&mmcc MDSS_AHB_CLK>,
+                                <&mmcc MDSS_AXI_CLK>,
+                                <&mmcc MDSS_VSYNC_CLK>;
+                       clock-names = "iface", "bus", "vsync";
One per line, please

+
+                       interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+                       interrupt-controller;
+                       #interrupt-cells = <1>;
We're not using the irq cell, is that necessary/should that be 0?

No. With 0 it would mean that there is a single interrupt for mdss source, which clearly is not the case.


+
+                       status = "disabled";
status should go last

+
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+                       ranges;
+
+                       mdp: display-controller@fd900000 {
+                               compatible = "qcom,msm8226-mdp5", "qcom,mdp5";
+                               reg = <0xfd900100 0x22000>;
+                               reg-names = "mdp_phys";
+
+                               interrupt-parent = <&mdss>;
+                               interrupts = <0>;
+
+                               clocks = <&mmcc MDSS_AHB_CLK>,
+                                        <&mmcc MDSS_AXI_CLK>,
+                                        <&mmcc MDSS_MDP_CLK>,
+                                        <&mmcc MDSS_VSYNC_CLK>;
+                               clock-names = "iface", "bus", "core", "vsync";
One per line, please

+
+                               ports {
+                                       #address-cells = <1>;
+                                       #size-cells = <0>;
Would port { work here? I remember one mdss component's bindings
didn't allow it but don't recall which one

Let's use ports /port@0 for uniformity even if there is just a single port always.


+
+                                       port@0 {
+                                               reg = <0>;
+                                               mdp5_intf1_out: endpoint {
+                                                       remote-endpoint = 
<&dsi0_in>;
+                                               };
+                                       };
+                               };
+                       };
+--
With best wishes
Dmitry

Reply via email to