Hi,
On 2/25/2025 6:26 PM, Lizhi Hou wrote:
> There is a timeout failure been found during stress tests. If the firmware
> generates a mailbox response right after driver clears the mailbox channel
> interrupt register, the hardware will not generate an interrupt for the
> response. This causes the unexpected mailbox command timeout.
>
> To handle this failure, driver checks the interrupt register before
> exiting mailbox_rx_worker(). If there is a new response, driver goes back
> to process it.
>
> Signed-off-by: Lizhi Hou <lizhi....@amd.com>
> ---
> drivers/accel/amdxdna/amdxdna_mailbox.c | 18 +++++++++++++++---
> 1 file changed, 15 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/accel/amdxdna/amdxdna_mailbox.c
> b/drivers/accel/amdxdna/amdxdna_mailbox.c
> index de7bf0fb4594..efe6cbc44d14 100644
> --- a/drivers/accel/amdxdna/amdxdna_mailbox.c
> +++ b/drivers/accel/amdxdna/amdxdna_mailbox.c
> @@ -348,8 +348,6 @@ static irqreturn_t mailbox_irq_handler(int irq, void *p)
> trace_mbox_irq_handle(MAILBOX_NAME, irq);
> /* Schedule a rx_work to call the callback functions */
> queue_work(mb_chann->work_q, &mb_chann->rx_work);
> - /* Clear IOHUB register */
> - mailbox_reg_write(mb_chann, mb_chann->iohub_int_addr, 0);
>
> return IRQ_HANDLED;
> }
> @@ -357,6 +355,7 @@ static irqreturn_t mailbox_irq_handler(int irq, void *p)
> static void mailbox_rx_worker(struct work_struct *rx_work)
> {
> struct mailbox_channel *mb_chann;
> + u32 iohub;
There is no need for this variable. Just use if (mailbox_reg_read()).
> int ret;
>
> mb_chann = container_of(rx_work, struct mailbox_channel, rx_work);
> @@ -366,6 +365,9 @@ static void mailbox_rx_worker(struct work_struct *rx_work)
> return;
> }
>
> +again:
> + mailbox_reg_write(mb_chann, mb_chann->iohub_int_addr, 0);
> +
> while (1) {
> /*
> * If return is 0, keep consuming next message, until there is
> @@ -380,9 +382,19 @@ static void mailbox_rx_worker(struct work_struct
> *rx_work)
> MB_ERR(mb_chann, "Unexpected ret %d, disable irq", ret);
> WRITE_ONCE(mb_chann->bad_state, true);
> disable_irq(mb_chann->msix_irq);
> - break;
> + return;
disable_irq() should not be called here. It will be called for the second time
in xdna_mailbox_stop_channel() and enable/disable calls should be balanced.
> }
> }
> +
> + /*
> + * The hardware will not generate interrupt if firmware creates a new
> + * response right after driver clears interrupt register. Check
> + * the interrupt register to make sure there is not any new response
> + * before exiting.
> + */
> + iohub = mailbox_reg_read(mb_chann, mb_chann->iohub_int_addr);
> + if (iohub)
> + goto again;
> }
>
> int xdna_mailbox_send_msg(struct mailbox_channel *mb_chann,
Regards,
Jacek
