W dniu 2025-11-16 o 15:37:15, Chen-Yu Tsai pisze:
On Sun, Nov 16, 2025 at 10:31 PM Kuba Szczodrzyński
<[email protected]> wrote:
W dniu 2025-11-16 o 15:03:18, Chen-Yu Tsai pisze:
On Sun, Nov 16, 2025 at 9:46 PM Kuba Szczodrzyński
<[email protected]> wrote:
[replying to v1 to keep the same series on Patchwork]
That is not the right way to do it.
If you reply to an old series, the tooling does not pickup the new version
as a separate series.
ChenYu
Hi,
I noticed that it indeed didn't work. However, Patchwork didn't pick up the v2
cover letter at all, so I thought replying to v2 would mess up the thread even
more.
That being said, the v3 cover letter is not visible there either.
Should I resend this as v4 [which message to reply to?] or send a completely
new series perhaps?
Each new version should be a completely new series.
If patchwork still didn't pick it up, then it's possible either your
patches didn't reach the mailing lists or the patchwork instances.
Please check lore to see if your patches are there.
The patches are on lore, but patchwork didn't pick them up because some were
sent with the wrong In-Reply-To header, and that created threading issues.
Assuming I understood your reply correctly, I'll send the entire series as v4
*without* the In-Reply-To header, which will create a new series on patchwork.
Regards
Kuba
ChenYu
I apologize for the confusion, this is my first time doing that.
Regards
Kuba
Some Allwinner chips (notably the D1s/T113 and the A100) have a "combo
MIPI DSI D-PHY" which is required when using single-link LVDS0. The same
PD0..PD9 pins are used for either DSI or LVDS.
Other than having to use the combo D-PHY, LVDS output is configured in
the same way as on older chips.
This series enables the sun6i MIPI D-PHY to also work in LVDS mode. It
is then configured by the LCD TCON, which allows connecting a
single-link LVDS display panel.
Changes in v2/v3:
- Applied code formatting changes from review comments
- Changed "dphy" to "combo-phy"
- Made the LVDS setup/teardown functions abort early in case of error
(adding a proper return value would require changes in several levels
of caller functions; perhaps could be done in a separate patch)
- Added the PHY properties to DT bindings
- Renamed lvds0_pins to lcd_lvds0_pins
- Rebased on top of drm/misc/kernel/for-linux-next
- Hopefully corrected the incomplete patch list of v2, which happened
due to an SMTP error
Kuba Szczodrzyński (6):
phy: allwinner: phy-sun6i-mipi-dphy: Support LVDS in combo D-PHY
drm/sun4i: Support LVDS using MIPI DSI combo D-PHY
drm/sun4i: Enable LVDS output on sun20i D1s/T113
dt-bindings: display: sun4i: Add D1s/T113 combo D-PHY bindings
riscv: dts: allwinner: d1s-t113: Add D-PHY to TCON LCD0
riscv: dts: allwinner: d1s-t113: Add LVDS0 pins
.../display/allwinner,sun4i-a10-tcon.yaml | 6 ++
.../boot/dts/allwinner/sunxi-d1s-t113.dtsi | 11 +++
drivers/gpu/drm/sun4i/sun4i_tcon.c | 50 +++++++++++++
drivers/gpu/drm/sun4i/sun4i_tcon.h | 6 ++
drivers/phy/allwinner/phy-sun6i-mipi-dphy.c | 70 ++++++++++++++++++-
5 files changed, 141 insertions(+), 2 deletions(-)
--
2.25.1
