no other cards...
I've attached iomem and dmesg.
-Dan
On Wed, 2003-02-12 at 23:11, Vladimir Dergachev wrote:
> What does Linux report in /proc/iomem and dmesg ?
> Do you have any other video cards in the system ?
>
> This sounds like PCI resource allocation issue.
>
> best
>
> Vladimir Dergachev
80000000-8fffffff : /pci@f2000000
80000000-8007ffff : Apple Computer Inc. KeyLargo Mac I/O
80008400-800084ff : ch-a (tx dma)
80008500-800085ff : ch-a (rx dma)
80008600-800086ff : ch-b (tx dma)
80008700-800087ff : ch-b (rx dma)
80008a00-80008aff : ata-4 (mac-io IDE DMA)
80008b00-80008bff : ata-3 (mac-io IDE DMA)
80008c00-80008cff : ata-3 (mac-io IDE DMA)
80013000-80013000 : ch-b
80013020-80013020 : ch-a
80016000-80017fff : via-pmu
8001f000-8001ffff : ata-4 (mac-io IDE IO)
80020000-80020fff : ata-3 (mac-io IDE IO)
80021000-80021fff : ata-3 (mac-io IDE IO)
80040000-8007ffff : interrupt-controller
80080000-8008007f : 3Com Corporation 3c900B-TPO [Etherlink XL TPO]
80081000-80081fff : Apple Computer Inc. KeyLargo USB (#2)
80081000-80081fff : usb-ohci
80082000-80082fff : Apple Computer Inc. KeyLargo USB
80082000-80082fff : usb-ohci
90000000-9fffffff : /pci@f0000000
90000000-9000ffff : ATI Technologies Inc Radeon 7500 QW
90000000-9000ffff : radeonfb
98000000-9fffffff : ATI Technologies Inc Radeon 7500 QW
98000000-9fffffff : radeonfb
f1000000-f1ffffff : /pci@f0000000
f3000000-f3ffffff : /pci@f2000000
f5000000-f5ffffff : /pci@f4000000
f5000000-f5000fff : Lucent Microelectronics FW323
f5200000-f53fffff : Apple Computer Inc. UniNorth GMAC (Sun GEM)
f5200000-f53fffff : eth0
f8000000-f8ffffff : uni-n
Memory BAT mapping: BAT2=256Mb, BAT3=256Mb, residual: 1024Mb
Total memory = 1536MB; using 4096kB for hash table (at c0400000)
Linux version 2.4.20-5asmp ([EMAIL PROTECTED]) (gcc version 3.2.1 20021207
(Red Hat Linux 8.0 3.2.1-2)) #1 SMP Sun Feb 2 00:59:35 EST 2003
Found Uninorth memory controller & host bridge, revision: 17
Mapped at 0xfdebc000
Found a Keylargo mac-io controller, rev: 3, mapped at 0xfde3c000
PowerMac motherboard: PowerMac G4 Silver
CPU MSCCR0 : 0x00008003
CPU HID1 : 0x80002c80
Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0
hose pci, pci_mem_offset: 00000000, start0: f1000000
io_base_virt: fd639000, io_base_phys: f0000000, isa_mem_base: 00000000
Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0
hose pci, pci_mem_offset: 00000000, start0: f3000000
io_base_virt: fce37000, io_base_phys: f2000000, isa_mem_base: 00000000
Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0
hose pci, pci_mem_offset: 00000000, start0: f5000000
io_base_virt: fc635000, io_base_phys: f4000000, isa_mem_base: 00000000
PMU driver 2 initialized for Core99, firmware: 0c
On node 0 totalpages: 393216
zone(0): 131072 pages.
zone(1): 0 pages.
zone(2): 262144 pages.
Kernel command line: root=/dev/hda12 video=radeon:dfp hdc=ide-scsi
ide_setup: hdc=ide-scsi
PowerMac using OpenPIC irq controller
OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc5ee000
OpenPIC timer frequency is 4.166666 MHz
GMT Delta read from XPRAM: 0 minutes, DST: off
time_init: decrementer frequency = 33.290001 MHz
Console: colour dummy device 80x25
Calibrating delay loop... 996.14 BogoMIPS
Memory: 1545760k available (2180k kernel code, 1228k data, 180k init, 1048576k highmem)
AGP special page: 0xdffff000
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 131072 (order: 7, 524288 bytes)
Page-cache hash table entries: 524288 (order: 9, 2097152 bytes)
POSIX conformance testing by UNIFIX
Entering SMP Mode...
smp_core99_probe: found 2 cpus
CPU0: L2CR is 80080000
CPU0: L3CR is 9f0b0000
CPU1: L2CR was 80000
CPU1: L2CR set to 80080000
CPU1: L3CR was 0
CPU1: L3CR set to 9f0b0000
Processor 1 found.
smp_software_tb_sync: 4 passes, final offset: 4
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
PCI: Probing PCI hardware
Scanning bus 00
Found 00:58 [106b/002d] 000600 00
Found 00:80 [1002/5157] 000300 00
Fixup res 1 (101) of dev 00:10.0: 400 -> 802400
Fixups for bus 00
Bus scan for 00 returning with max=00
Scanning bus 10
Found 10:58 [106b/002e] 000600 00
Found 10:a0 [10b7/9004] 000200 00
Found 10:b8 [106b/0022] 00ff00 00
Found 10:c0 [106b/0019] 000c03 00
Found 10:c8 [106b/0019] 000c03 00
Fixups for bus 10
Bus scan for 10 returning with max=10
Scanning bus 20
Found 20:58 [106b/002f] 000600 00
Found 20:70 [11c1/5811] 000c00 00
Found 20:78 [106b/0021] 000200 00
Fixups for bus 20
Bus scan for 20 returning with max=20
PCI->OF bus map:
0 -> 0
16 -> 0
32 -> 0
PCI:00:10.0: Resource 0: 98000000-9fffffff (f=1208), vd: 1002, dev: 5157
PCI:00:10.0: Resource 2: 90000000-9000ffff (f=200), vd: 1002, dev: 5157
PCI:10:17.0: Resource 0: 80000000-8007ffff (f=200), vd: 106b, dev: 0022
PCI:20:0f.0: Resource 0: f5200000-f53fffff (f=200), vd: 106b, dev: 0021
PCI:00:10.0: Resource 1: 00802400-008024ff (f=101), vd: 1002, dev: 5157
PCI:10:14.0: Resource 0: 00000400-0000047f (f=101), vd: 10b7, dev: 9004
PCI:10:14.0: Resource 1: 80080000-8008007f (f=200), vd: 10b7, dev: 9004
PCI:10:18.0: Resource 0: 80082000-80082fff (f=200), vd: 106b, dev: 0019
PCI:10:19.0: Resource 0: 80081000-80081fff (f=200), vd: 106b, dev: 0019
PCI:20:0e.0: Resource 0: f5000000-f5000fff (f=200), vd: 11c1, dev: 5811
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Thermal assist unit not available
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
udf: registering filesystem
PCI: Enabling device 00:10.0 (0086 -> 0087)
radeonfb: ref_clk=2700, ref_div=12, xclk=20025 from OF
radeonfb: detected DFP panel size from EDID: 1280x1024
Console: switching to colour frame buffer device 160x64
radeonfb: ATI Radeon 7500 QW DDR SGRAM 32 MB
radeonfb: DVI port DFP monitor connected
radeonfb: CRT port no monitor connected
input0: Macintosh mouse button emulation
pty: 256 Unix98 ptys configured
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: Found Apple KeyLargo ATA-4 controller, bus ID 2
ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0
ide2: Found Apple KeyLargo ATA-3 controller, bus ID 1
Probing IDE interface ide0...
hda: ST380021A, ATA DISK drive
hdb: MAXTOR 6L080J4, ATA DISK drive
Probing IDE interface ide1...
hdc: PIONEER DVD-RW DVR-104, ATAPI CD/DVD-ROM drive
Probing IDE interface ide2...
ide0 at 0xe6310000-0xe6310007,0xe6310160 on irq 19
ide1 at 0xe6314000-0xe6314007,0xe6314160 on irq 20
hda: Enabling Ultra DMA 4
blk: queue c0359968, I/O limit 4095Mb (mask 0xffffffff)
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63, UDMA(66)
hdb: Enabling Ultra DMA 4
blk: queue c0359ab8, I/O limit 4095Mb (mask 0xffffffff)
hdb: 156355584 sectors (80054 MB) w/1819KiB Cache, CHS=155114/16/63, UDMA(66)
hdc: Enabling MultiWord DMA 2
Partition check:
hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13
hdb: [mac] hdb1 hdb2 hdb3
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
sungem.c:v0.97 3/20/02 David S. Miller ([EMAIL PROTECTED])
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:03:93:6d:7f:04
eth0: Found BCM5421 PHY
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: PIONEER Model: DVD-RW DVR-104 Rev: A227
Type: CD-ROM ANSI SCSI revision: 02
mesh: configured for synchronous 5 MB/s
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
macserial: i2c-modem detected, id: 1
PowerMac Z8530 serial driver version 2.0
tty00 at 0xe3354020 (irq = 22) is a Z8530 ESCC (internal modem)
tty01 at 0xe335b000 (irq = 23) is a Z8530 ESCC
Macintosh non-volatile memory driver v1.0
apm_emu: APM Emulation 0.5 initialized.
usb.c: registered new driver usbdevfs
adb: starting probe task...
adb: finished probe task...
usb.c: registered new driver hub
PCI: Enabling device 10:18.0 (0000 -> 0002)
PCI: Enabling bus mastering for device 10:18.0
usb-ohci.c: USB OHCI at membase 0xe3361000, IRQ 27
usb-ohci.c: usb-10:18.0, Apple Computer Inc. KeyLargo USB
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Enabling device 10:19.0 (0000 -> 0002)
PCI: Enabling bus mastering for device 10:19.0
usb-ohci.c: USB OHCI at membase 0xe3363000, IRQ 28
usb-ohci.c: usb-10:19.0, Apple Computer Inc. KeyLargo USB (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 344k freed
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 180k init 8k chrp 8k prep
hub.c: new USB device 10:18.0-2, assigned address 2
hub.c: USB hub found
hub.c: 3 ports detected
hub.c: new USB device 10:18.0-2.2, assigned address 3
hub.c: USB hub found
hub.c: 3 ports detected
hub.c: new USB device 10:18.0-2.3, assigned address 4
: USB HID v0.01 Pointer [05ac:9217] on usb1:4.0
hub.c: new USB device 10:18.0-2.2.1, assigned address 5
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,12), internal journal
Adding Swap: 524280k swap-space (priority -1)
input1: USB HID v10.01 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on
usb1:5.0
input2: USB HID v10.01 Pointer [Mitsumi Electric Apple Extended USB Keyboard] on
usb1:5.1
hub.c: new USB device 10:18.0-2.2.3, assigned address 6
input3: USB HID v10.01 Mouse [KOOL Contour UniMouse Optical] on usb1:6.0
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,66), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,13), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ieee1394: sbp2: Please load the lower level IEEE-1394 driver (e.g. ohci1394) before
sbp2...
ohci1394: $Rev: 578 $ Ben Collins <[EMAIL PROTECTED]>
ohci1394_0: Unexpected PCI resource length of 1000!
ohci1394_0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max Packet=[2048]
ieee1394: Host added: Node[00:1023] GUID[00000000fe6d7f04] [Linux OHCI-1394]
ieee1394: Host removed: Node[00:1023] GUID[00000000fe6d7f04] [Linux OHCI-1394]
ip_tables: (C) 2000-2002 Netfilter core team
eth0: Link is up at 100 Mbps, full-duplex.
eth0: Pause is disabled
ip_conntrack version 2.1 (8192 buckets, 65536 max) - 292 bytes per conntrack
ISO 9660 Extensions: Microsoft Joliet Level 1
ISOFS: changing to secondary root
