Yes!Now it's working! The network card Attansic L2 included in the motherboard Asus P5GC-MX/1333 can be considered as 100% compatible with OpenSolaris 2009.06. Great job, Masa, thanks a lot for your time and effort!!! Best regards,
HeCSa. 2009/7/8 Masa Murayama <khf04...@nifty.ne.jp> > ----- Original Message ----- > >Subject: Re: [driver-discuss] ASUS P5GC-MX/1333 & Attansic L2 > >From: HeCSa <hsalt...@gmail.com> > >To: Masa Murayama <khf04...@nifty.ne.jp> > >Cc: driver-discuss@opensolaris.org > >Date: Tue, 07 Jul 2009 20:20:52 -0300 > > > > > >Hello, Masa! > >Thanks for your response and commands! > >Well...the network card still does not work, I've extracted the logs, > >which I copy here: > > > >ifconfig -a: (no changes) > > > >lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu > >8232 index 1 > > inet 127.0.0.1 netmask ff000000 > >atge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index > >2 > > inet 10.100.100.2 netmask ffffff00 broadcast 10.100.100.255 > > ether 0:1f:c6:8:f5:7f > >lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu > >8252 index 1 > > inet6 ::1/128 > > > >dmesg | grep atge: (here comes the first change) > > > >Jul 7 20:00:14 osol01 atge: [ID 130221 kern.info] atge0: Attansic L2 > >(vid: 0x1969, did: 0x2048, revid: 0xa0) > >Jul 7 20:00:14 osol01 atge: [ID 451511 kern.info] atge0: MII PHY > >(0x004dd022) found at 0 > >Jul 7 20:00:14 osol01 atge: [ID 679413 kern.info] atge0: PHY > >control:1000<ANE>, > > >status:7849<100_BASEX_FD,100_BASEX,10_BASE_FD,10_BASE,MFPRMBLSUPR,CANAUTONEG, > EXTENDED>, > advert:de1<ASM_DIR,PAUSE,100BASE_TX_FD,100BASE_TX,10BASE_T_FD,10BAS > E_T>, lpar:0, exp:0 > >Jul 7 20:00:14 osol01 gld: [ID 944156 kern.info] atge0: atheros L1 nic > >driver v2.6.4: type "ether" mac address 00:1f:c6:08:f5:7f > >Jul 7 20:00:14 osol01 pcie_pci: [ID 586369 kern.info] PCIE-device: > >pci1043,8...@0, atge0 > >Jul 7 20:00:14 osol01 genunix: [ID 936769 kern.info] atge0 > >is /p...@0,0/pci8086,2...@1c,1/pci1043,8...@0 > >Jul 7 20:00:14 osol01 atge: [ID 188825 kern.info] atge0: gem_add_intrs: > >supported intr_types:3 > >Jul 7 20:00:14 osol01 pcplusmp: [ID 805372 kern.info] pcplusmp: > >pci1969,2048 (atge) instance 0 irq 0x19 vector 0x60 ioapic 0xff intin > >0xff is bound to cpu 0 > >Jul 7 20:00:14 osol01 atge: [ID 716252 kern.info] atge0: resetting PHY > > > >(there is no negotiation here) > > > >grep atge /var/adm/messages: > > > >Jul 7 20:00:14 osol01 atge: [ID 130221 kern.info] atge0: Attansic L2 > >(vid: 0x1969, did: 0x2048, revid: 0xa0) > >Jul 7 20:00:14 osol01 atge: [ID 451511 kern.info] atge0: MII PHY > >(0x004dd022) found at 0 > >Jul 7 20:00:14 osol01 atge: [ID 679413 kern.info] atge0: PHY > >control:1000<ANE>, > > >status:7849<100_BASEX_FD,100_BASEX,10_BASE_FD,10_BASE,MFPRMBLSUPR,CANAUTONEG, > EXTENDED>, > advert:de1<ASM_DIR,PAUSE,100BASE_TX_FD,100BASE_TX,10BASE_T_FD,10BAS > E_T>, lpar:0, exp:0 > >Jul 7 20:00:14 osol01 gld: [ID 944156 kern.info] atge0: atheros L1 nic > >driver v2.6.4: type "ether" mac address 00:1f:c6:08:f5:7f > >Jul 7 20:00:14 osol01 pcie_pci: [ID 586369 kern.info] PCIE-device: > >pci1043,8...@0, atge0 > >Jul 7 20:00:14 osol01 genunix: [ID 936769 kern.info] atge0 > >is /p...@0,0/pci8086,2...@1c,1/pci1043,8...@0 > >Jul 7 20:00:14 osol01 atge: [ID 188825 kern.info] atge0: gem_add_intrs: > >supported intr_types:3 > >Jul 7 20:00:14 osol01 pcplusmp: [ID 805372 kern.info] pcplusmp: > >pci1969,2048 (atge) instance 0 irq 0x19 vector 0x60 ioapic 0xff intin > >0xff is bound to cpu 0 > >Jul 7 20:00:14 osol01 atge: [ID 716252 kern.info] atge0: resetting PHY > > > >(same as before, no negotiation) > > > >I understand that my router supports 10 mbps, it's a Linksys WRT54G. I > >confirmed this with the manual, it has four 10/100 RJ45 switched ports. > > Did you check link/speed/duplex lamps in the front panel of the > Linksys WRT54G? > > I prepared the bugfix of atge below, which I mentioned in the previous > mail. > please try it. > > http://homepage2.nifty.com/mrym3/taiyodo/atge-2.6.5t0.tar.gz > > To update atge driver, do following after you extract files from the > tarball, > > # /usr/ccs/bin/make install > # init 6 > > If it won't work, it is difficult to solve the issue right now. > > -masa > > >Thanks again, Masa! > >Best regards, > > > >HeCSa. > > > > > > > > -- HeCSa
_______________________________________________ driver-discuss mailing list driver-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/driver-discuss
