Enable only those interrupts that we can handle & acknowledge in the
interrupt handler.
At least on EdgeRouter Lite, the hardware may occasionally interrupt with
some error condition when the physical link status changes frequently.
Since the interrupt condition is not acked properly, this leads to the
following warning and the IRQ gets disabled completely:
[ 41.324700] eth0: Link down
[ 44.324721] eth0: 1000 Mbps Full duplex, port 0, queue 0
[ 44.885590] irq 117: nobody cared (try booting with the "irqpoll" option)
[ 44.892397] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
3.11.0-rc5-edge-los.git-27d042f-dirty-00950-gaa42f2d-dirty #8
[ 44.902825] Stack : ffffffff815c0000 0000000000000004 0000000000000003
0000000000000000
ffffffff81fd0000 ffffffff815c0000 0000000000000004 ffffffff8118530c
ffffffff815c0000 ffffffff811858d8 0000000000000000 0000000000000000
ffffffff81fd0000 ffffffff81fc0000 ffffffff8152f3a0 ffffffff815b7bf7
ffffffff81fc6688 ffffffff815b8060 0000000000000000 0000000000000000
0000000000000000 ffffffff815346c8 ffffffff815346b0 ffffffff814a6a18
ffffffff8158b848 ffffffff81145614 ffffffff81593800 ffffffff81187174
ffffffff815b7d00 ffffffff8158b760 0000000000000000 ffffffff814a9184
0000000000000000 0000000000000000 0000000000000000 0000000000000000
0000000000000000 ffffffff811203b8 0000000000000000 0000000000000000
...
[ 44.968408] Call Trace:
[ 44.970873] [<ffffffff811203b8>] show_stack+0x68/0x80
[ 44.975937] [<ffffffff814a9184>] dump_stack+0x78/0xb8
[ 44.980999] [<ffffffff811aac54>] __report_bad_irq+0x44/0x108
[ 44.986662] [<ffffffff811ab238>] note_interrupt+0x248/0x2a0
[ 44.992240] [<ffffffff811a85e4>] handle_irq_event_percpu+0x144/0x200
[ 44.998598] [<ffffffff811a86f4>] handle_irq_event+0x54/0x90
[ 45.004176] [<ffffffff811ab908>] handle_level_irq+0xd0/0x148
[ 45.009839] [<ffffffff811a7b04>] generic_handle_irq+0x34/0x50
[ 45.015589] [<ffffffff8111dae8>] do_IRQ+0x18/0x30
[ 45.020301] [<ffffffff8110486c>] plat_irq_dispatch+0x74/0xb8
[ 45.025958]
[ 45.027451] handlers:
[ 45.029731] [<ffffffff813fca10>] cvm_oct_rgmii_rml_interrupt
[ 45.035397] Disabling IRQ #117
[ 45.038742] Port 0 receive error code 13, packet dropped
[ 46.324719] eth0: Link down
[ 48.324733] eth0: 1000 Mbps Full duplex, port 0, queue 0
Reported-by: "Jason A. Donenfeld" <ja...@zx2c4.com>
Signed-off-by: Aaro Koskinen <aaro.koski...@iki.fi>
---
drivers/staging/octeon/ethernet-rgmii.c | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
diff --git a/drivers/staging/octeon/ethernet-rgmii.c
b/drivers/staging/octeon/ethernet-rgmii.c
index d8f5f69..ea53af3 100644
--- a/drivers/staging/octeon/ethernet-rgmii.c
+++ b/drivers/staging/octeon/ethernet-rgmii.c
@@ -373,9 +373,7 @@ int cvm_oct_rgmii_init(struct net_device *dev)
* Enable interrupts on inband status changes
* for this port.
*/
- gmx_rx_int_en.u64 =
- cvmx_read_csr(CVMX_GMXX_RXX_INT_EN
- (index, interface));
+ gmx_rx_int_en.u64 = 0;
gmx_rx_int_en.s.phy_dupx = 1;
gmx_rx_int_en.s.phy_link = 1;
gmx_rx_int_en.s.phy_spd = 1;
--
1.8.3.2
_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
