On Wed, Feb 26, 2014 at 08:41:38AM -0500, Mark Hounschell wrote:
> -static void dgap_sysfs_create(struct board_t *brd)
> +static int dgap_tty_register_ports(struct board_t *brd)
> {
> struct channel_t *ch;
> - int j = 0;
> + int i;
> +
> + brd->SerialPorts = kcalloc(brd->nasync, sizeof(*brd->SerialPorts),
> + GFP_KERNEL);
> + if (brd->SerialPorts == NULL) {
> + pr_err("dgap: Cannot allocate serial port memory\n");
Don't add these error messages here. kcalloc() already prints a much
better error message.
> + return -ENOMEM;
> + }
> + for (i = 0; i < brd->nasync; i++)
> + tty_port_init(&brd->SerialPorts[i]);
> +
> + brd->PrinterPorts = kcalloc(brd->nasync, sizeof(*brd->PrinterPorts),
> + GFP_KERNEL);
> + if (brd->PrinterPorts == NULL) {
> + pr_err("dgap: Cannot allocate printer port memory\n");
kfree(brd->SerialPorts);
> + return -ENOMEM;
> + }
> + for (i = 0; i < brd->nasync; i++)
> + tty_port_init(&brd->PrinterPorts[i]);
>
> ch = brd->channels[0];
> - for (j = 0; j < brd->nasync; j++, ch = brd->channels[j]) {
> + for (i = 0; i < brd->nasync; i++, ch = brd->channels[i]) {
> struct device *classp;
Put a blank line after the declaration block.
> - classp = tty_register_device(brd->SerialDriver, j,
> - &(ch->ch_bd->pdev->dev));
> +
> + classp = tty_port_register_device(&brd->SerialPorts[i],
> + brd->SerialDriver, brd->firstminor + i, NULL);
The more traditional way to break up the long lines is:
classp = tty_port_register_device(&brd->SerialPorts[i],
brd->SerialDriver,
brd->firstminor + i, NULL);
dgap_create_tty_sysfs(&ch->ch_tun, classp);
ch->ch_tun.un_sysfs = classp;
classp = tty_port_register_device(&brd->PrinterPorts[i],
brd->PrintDriver,
brd->firstminor + i,
NULL);
dgap_create_tty_sysfs(&ch->ch_pun, classp);
ch->ch_pun.un_sysfs = classp;
(also i re-ordered the last two lines).
(also I wouldn't have sent this email at all if there hadn't been that
missing kfree()).
regards,
dan carpenter
> +
> ch->ch_tun.un_sysfs = classp;
> dgap_create_tty_sysfs(&ch->ch_tun, classp);
>
> - classp = tty_register_device(brd->PrintDriver, j,
> - &(ch->ch_bd->pdev->dev));
> + classp = tty_port_register_device(&brd->PrinterPorts[i],
> + brd->PrintDriver, brd->firstminor + i, NULL);
> +
> ch->ch_pun.un_sysfs = classp;
> dgap_create_tty_sysfs(&ch->ch_pun, classp);
> }
> dgap_create_ports_sysfiles(brd);
> +
> + return 0;
_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
