Am 25.03.2016 12:33, schrieb Daeseok Youn:
> the dgnc_offset_table has a same value with (1 << port).
> So I tried to replace dgnc_offset_table array with 1 << port.
> And also there are redundant assignments(tmp and current_port)
> inside while loop for checking uart port, and remove them.
>
> Signed-off-by: Daeseok Youn <daeseok.y...@gmail.com>
> ---
> Greg, This patch depends on previous patches.
> here are links(previous):
> 1. https://lkml.org/lkml/2016/3/24/661
> 2. https://lkml.org/lkml/2016/3/24/663
>
> if those patches are failed to merge, I will send them again after
> fixing them.
>
> thanks.
>
> drivers/staging/dgnc/dgnc_neo.c | 44
> +++++++++++++++++++----------------------
> 1 file changed, 20 insertions(+), 24 deletions(-)
>
> diff --git a/drivers/staging/dgnc/dgnc_neo.c b/drivers/staging/dgnc/dgnc_neo.c
> index d732e6e..8b6bc73 100644
> --- a/drivers/staging/dgnc/dgnc_neo.c
> +++ b/drivers/staging/dgnc/dgnc_neo.c
> @@ -77,9 +77,6 @@ struct board_ops dgnc_neo_ops = {
> .send_immediate_char = neo_send_immediate_char
> };
>
> -static uint dgnc_offset_table[8] = { 0x01, 0x02, 0x04, 0x08,
> - 0x10, 0x20, 0x40, 0x80 };
> -
> /*
> * This function allows calls to ensure that all outstanding
> * PCI writes have been completed, by doing a PCI read against
> @@ -923,9 +920,7 @@ static irqreturn_t neo_intr(int irq, void *voidbrd)
> struct dgnc_board *brd = voidbrd;
> struct channel_t *ch;
> int port = 0;
> - int type = 0;
> - int current_port;
> - u32 tmp;
> + int type;
> u32 uart_poll;
> unsigned long flags;
> unsigned long flags2;
> @@ -960,28 +955,29 @@ static irqreturn_t neo_intr(int irq, void *voidbrd)
>
> /* At this point, we have at least SOMETHING to service, dig further...
> */
>
> - current_port = 0;
> -
> /* Loop on each port */
> while ((uart_poll & 0xff) != 0) {
> - tmp = uart_poll;
> -
> - /* Check current port to see if it has interrupt pending */
> - if ((tmp & dgnc_offset_table[current_port]) != 0) {
> - port = current_port;
> - type = tmp >> (8 + (port * 3));
> - type &= 0x7;
> - } else {
> - current_port++;
> - continue;
> - }
> + int i;
>
> - /* Remove this port + type from uart_poll */
> - uart_poll &= ~(dgnc_offset_table[port]);
> + type = 0;
>
> - if (!type) {
> - /* If no type, just ignore it, and move onto next port
> */
> - continue;
> + for (i = port; i < MAXPORTS; i++) {
> + unsigned int offset_table = 0x1 << i;
> +
> + /* Check current port to see
> + * if it has interrupt pending
> + */
> + if ((uart_poll & offset_table) != 0) {
> + port = i;
> + type = uart_poll >> (8 + (port * 3));
> + type &= 0x7;
> +
> + /* Remove this port + type from uart_poll */
> + uart_poll &= ~(offset_table);
why not: art_poll &= ~ (0x1 << i);
then you can easy eliminate offset_table
btw: why do you need i ?
re,
wh
> + }
> +
> + if (type)
> + break;
> }
>
> /* Switch on type of interrupt we have */
_______________________________________________
devel mailing list
de...@linuxdriverproject.org
http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
