On Mon, Jul 16 2018, Sergio Paracuellos wrote: > This patch series include an attempt to avoid the use of custom > read and writes in driver code and use PCI subsystem common ones. > > In order to do this 'map_bus' callback is implemented and also > data structures for driver are included. The regs base address > is being readed from device tree and the driver gets clean a lot > of code. > > Changes in v4: > - Rebased onto staging-next. > > Changes in v3: > - Include new patches to delete all RALINK_BASE definition > dependant code and be able to avoid use of pci_legacy code. > - use devm_of_pci_get_host_bridge_resources, > devm_request_pci_bus_resources and pci_scan_root_bus_bridge > and pci_bus_add_devices > > Changes in v2: > - squash PATCH 1 and PATCH 2 of previous series in only PATCH 1 > - Change name for host structure. > - Create a new port structure (platform has 3 pcie controllers) > - Replace the use of pci_generic_config_[read|write]32 in favour > of pci_generic_config_[read|write] and change map_bus implemen- > tation for hopefully the right one. > > Best regards,
Thanks for these.
I added
diff --git a/arch/mips/ralink/Kconfig b/arch/mips/ralink/Kconfig
index 1f9cb0e3c79a..50779b3379db 100644
--- a/arch/mips/ralink/Kconfig
+++ b/arch/mips/ralink/Kconfig
@@ -51,6 +51,7 @@ choice
select COMMON_CLK
select CLKSRC_MIPS_GIC
select HW_HAS_PCI
+ select PCI_DRIVERS_GENERIC
endchoice
choice
so that I could build and test it - maybe there is somewhere else that
"select" can go while this is still in staging..
The system boots and can see the three pcie-attached SATA controllers:
# lspci
00:00.0 PCI bridge: Device 0e8d:0801 (rev 01)
00:01.0 PCI bridge: Device 0e8d:0801 (rev 01)
00:02.0 PCI bridge: Device 0e8d:0801 (rev 01)
01:00.0 IDE interface: ASMedia Technology Inc. ASM1061 SATA IDE Controller (rev
02)
02:00.0 IDE interface: ASMedia Technology Inc. ASM1061 SATA IDE Controller (rev
02)
03:00.0 IDE interface: ASMedia Technology Inc. ASM1061 SATA IDE Controller (rev
02)
but it cannot see the drive that is plugged into one of these.
Below is the first 10 seconds of dmesg.
I suspect the relevant bit is
[ 8.680000] ahci: probe of 0000:01:00.0 failed with error -22
[ 8.700000] ahci: probe of 0000:02:00.0 failed with error -22
[ 8.710000] ahci: probe of 0000:03:00.0 failed with error -22
I haven't dug deeper yet.
Thanks,
NeilBrown
[ 0.000000] Linux version 4.18.0-rc5+ (neilb@noble) (gcc version 7.2.0
(GCC)) #205 SMP Wed Jul 25 08:12:13 AEST 2018
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is GB-PC1
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 1c000000 @ 00000000 (usable)
[ 0.000000] memory: 04000000 @ 20000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32
bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000001fffffff]
[ 0.000000] HighMem [mem 0x0000000020000000-0x0000000023ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000001bffffff]
[ 0.000000] node 0: [mem 0x0000000020000000-0x0000000023ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000023ffffff]
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] Normal zone: 1024 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 114688 pages, LIFO batch:31
[ 0.000000] HighMem zone: 16384 pages, LIFO batch:3
[ 0.000000] random: get_random_bytes called from start_kernel+0xb4/0x4ec
with crng_init=0
[ 0.000000] percpu: Embedded 15 pages/cpu @(ptrval) s30480 r8192 d22768
u61440
[ 0.000000] pcpu-alloc: s30480 r8192 d22768 u61440 alloc=15*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttyS0,57600
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Writing ErrCtl register=000108a2
[ 0.000000] Readback ErrCtl register=000108a2
[ 0.000000] Memory: 504788K/524288K available (6131K kernel code, 232K
rwdata, 1052K rodata, 6524K init, 241K bss, 19500K reserved, 0K cma-reserved,
65536K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 256
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles:
0xcf914c9718, max_idle_ns: 440795231327 ns
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps
every 21474836475000000ns
[ 0.010000] Calibrating delay loop... 597.60 BogoMIPS (lpj=2988032)
[ 0.070000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] Hierarchical SRCU implementation.
[ 0.110000] smp: Bringing up secondary CPUs ...
[ 0.120000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.120000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32
bytes
[ 0.120000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.120000] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.180000] Synchronize counters for CPU 1: done.
[ 0.220000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.220000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32
bytes
[ 0.220000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.220000] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.280000] Synchronize counters for CPU 2: done.
[ 0.320000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.320000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32
bytes
[ 0.320000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.320000] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.380000] Synchronize counters for CPU 3: done.
[ 0.420000] smp: Brought up 1 node, 4 CPUs
[ 0.430000] devtmpfs: initialized
[ 0.480000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 19112604462750000 ns
[ 0.490000] futex hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.500000] pinctrl core: initialized pinctrl subsystem
[ 0.510000] NET: Registered protocol family 16
[ 0.560000] FPU Affinity set after 12000 emulations
[ 0.570000] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges:
[ 0.580000] mt7621-pci 1e140000.pcie: MEM 0x60000000..0x6fffffff ->
0x00000000
[ 0.600000] mt7621-pci 1e140000.pcie: IO 0x1e160000..0x1e16ffff ->
0x00000000
[ 0.910000] ***** Xtal 40MHz *****
[ 0.920000] Port 0 N_FTS = 1b102800
[ 0.930000] Port 1 N_FTS = 1b102800
[ 0.930000] Port 2 N_FTS = 1b102800
[ 1.990000] PCIE0 enabled
[ 2.000000] PCIE1 enabled
[ 2.000000] PCIE2 enabled
[ 2.010000] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 2.020000] pci_bus 0000:00: No busn resource found for root bus, will use
[bus 00-ff]
[ 2.030000] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 2.040000] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.040000] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 2.040000] pci 0000:00:00.0: supports D1
[ 2.040000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 2.040000] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 2.040000] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.040000] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 2.040000] pci 0000:00:01.0: supports D1
[ 2.040000] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 2.040000] pci 0000:00:02.0: [0e8d:0801] type 01 class 0x060400
[ 2.040000] pci 0000:00:02.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 2.040000] pci 0000:00:02.0: reg 0x14: [mem 0x00000000-0x0000ffff]
[ 2.040000] pci 0000:00:02.0: supports D1
[ 2.040000] pci 0000:00:02.0: PME# supported from D0 D1 D3hot
[ 2.040000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]),
reconfiguring
[ 2.060000] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]),
reconfiguring
[ 2.070000] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]),
reconfiguring
[ 2.090000] pci 0000:01:00.0: [1b21:0611] type 00 class 0x010185
[ 2.090000] pci 0000:01:00.0: reg 0x10: [io 0x0000-0x0007]
[ 2.090000] pci 0000:01:00.0: reg 0x14: [io 0x0000-0x0003]
[ 2.090000] pci 0000:01:00.0: reg 0x18: [io 0x0000-0x0007]
[ 2.090000] pci 0000:01:00.0: reg 0x1c: [io 0x0000-0x0003]
[ 2.090000] pci 0000:01:00.0: reg 0x20: [io 0x0000-0x000f]
[ 2.090000] pci 0000:01:00.0: reg 0x24: [mem 0x00000000-0x000001ff]
[ 2.090000] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 2.100000] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 2.100000] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff]
[ 2.100000] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff
pref]
[ 2.100000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 2.100000] pci 0000:02:00.0: [1b21:0611] type 00 class 0x010185
[ 2.100000] pci 0000:02:00.0: reg 0x10: [io 0x0000-0x0007]
[ 2.100000] pci 0000:02:00.0: reg 0x14: [io 0x0000-0x0003]
[ 2.100000] pci 0000:02:00.0: reg 0x18: [io 0x0000-0x0007]
[ 2.100000] pci 0000:02:00.0: reg 0x1c: [io 0x0000-0x0003]
[ 2.100000] pci 0000:02:00.0: reg 0x20: [io 0x0000-0x000f]
[ 2.100000] pci 0000:02:00.0: reg 0x24: [mem 0x00000000-0x000001ff]
[ 2.100000] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 2.110000] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 2.110000] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff]
[ 2.110000] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff
pref]
[ 2.110000] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 2.110000] pci 0000:03:00.0: [1b21:0611] type 00 class 0x010185
[ 2.110000] pci 0000:03:00.0: reg 0x10: [io 0x0000-0x0007]
[ 2.110000] pci 0000:03:00.0: reg 0x14: [io 0x0000-0x0003]
[ 2.110000] pci 0000:03:00.0: reg 0x18: [io 0x0000-0x0007]
[ 2.110000] pci 0000:03:00.0: reg 0x1c: [io 0x0000-0x0003]
[ 2.110000] pci 0000:03:00.0: reg 0x20: [io 0x0000-0x000f]
[ 2.110000] pci 0000:03:00.0: reg 0x24: [mem 0x00000000-0x000001ff]
[ 2.120000] pci 0000:00:02.0: PCI bridge to [bus 03-ff]
[ 2.130000] pci 0000:00:02.0: bridge window [io 0x0000-0x0fff]
[ 2.130000] pci 0000:00:02.0: bridge window [mem 0x00000000-0x000fffff]
[ 2.130000] pci 0000:00:02.0: bridge window [mem 0x00000000-0x000fffff
pref]
[ 2.130000] pci_bus 0000:03: busn_res: [bus 03-ff] end is updated to 03
[ 2.130000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 03
[ 2.130000] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 2.140000] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.150000] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 2.170000] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.180000] pci 0000:00:02.0: BAR 0: no space for [mem size 0x80000000]
[ 2.190000] pci 0000:00:02.0: BAR 0: failed to assign [mem size 0x80000000]
[ 2.210000] pci 0000:00:00.0: BAR 8: no space for [mem size 0x00100000]
[ 2.220000] pci 0000:00:00.0: BAR 8: failed to assign [mem size 0x00100000]
[ 2.230000] pci 0000:00:00.0: BAR 9: no space for [mem size 0x00100000 pref]
[ 2.250000] pci 0000:00:00.0: BAR 9: failed to assign [mem size 0x00100000
pref]
[ 2.260000] pci 0000:00:01.0: BAR 8: no space for [mem size 0x00100000]
[ 2.270000] pci 0000:00:01.0: BAR 8: failed to assign [mem size 0x00100000]
[ 2.290000] pci 0000:00:01.0: BAR 9: no space for [mem size 0x00100000 pref]
[ 2.300000] pci 0000:00:01.0: BAR 9: failed to assign [mem size 0x00100000
pref]
[ 2.320000] pci 0000:00:02.0: BAR 8: no space for [mem size 0x00100000]
[ 2.330000] pci 0000:00:02.0: BAR 8: failed to assign [mem size 0x00100000]
[ 2.340000] pci 0000:00:02.0: BAR 9: no space for [mem size 0x00100000 pref]
[ 2.360000] pci 0000:00:02.0: BAR 9: failed to assign [mem size 0x00100000
pref]
[ 2.370000] pci 0000:00:00.0: BAR 1: no space for [mem size 0x00010000]
[ 2.380000] pci 0000:00:00.0: BAR 1: failed to assign [mem size 0x00010000]
[ 2.400000] pci 0000:00:01.0: BAR 1: no space for [mem size 0x00010000]
[ 2.410000] pci 0000:00:01.0: BAR 1: failed to assign [mem size 0x00010000]
[ 2.420000] pci 0000:00:02.0: BAR 1: no space for [mem size 0x00010000]
[ 2.440000] pci 0000:00:02.0: BAR 1: failed to assign [mem size 0x00010000]
[ 2.450000] pci 0000:00:00.0: BAR 7: no space for [io size 0x1000]
[ 2.460000] pci 0000:00:00.0: BAR 7: failed to assign [io size 0x1000]
[ 2.480000] pci 0000:00:01.0: BAR 7: no space for [io size 0x1000]
[ 2.490000] pci 0000:00:01.0: BAR 7: failed to assign [io size 0x1000]
[ 2.500000] pci 0000:00:02.0: BAR 7: no space for [io size 0x1000]
[ 2.510000] pci 0000:00:02.0: BAR 7: failed to assign [io size 0x1000]
[ 2.530000] pci 0000:01:00.0: BAR 5: no space for [mem size 0x00000200]
[ 2.540000] pci 0000:01:00.0: BAR 5: failed to assign [mem size 0x00000200]
[ 2.550000] pci 0000:01:00.0: BAR 4: no space for [io size 0x0010]
[ 2.570000] pci 0000:01:00.0: BAR 4: failed to assign [io size 0x0010]
[ 2.580000] pci 0000:01:00.0: BAR 0: no space for [io size 0x0008]
[ 2.590000] pci 0000:01:00.0: BAR 0: failed to assign [io size 0x0008]
[ 2.600000] pci 0000:01:00.0: BAR 2: no space for [io size 0x0008]
[ 2.620000] pci 0000:01:00.0: BAR 2: failed to assign [io size 0x0008]
[ 2.630000] pci 0000:01:00.0: BAR 1: no space for [io size 0x0004]
[ 2.640000] pci 0000:01:00.0: BAR 1: failed to assign [io size 0x0004]
[ 2.650000] pci 0000:01:00.0: BAR 3: no space for [io size 0x0004]
[ 2.670000] pci 0000:01:00.0: BAR 3: failed to assign [io size 0x0004]
[ 2.680000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 2.690000] pci 0000:02:00.0: BAR 5: no space for [mem size 0x00000200]
[ 2.700000] pci 0000:02:00.0: BAR 5: failed to assign [mem size 0x00000200]
[ 2.720000] pci 0000:02:00.0: BAR 4: no space for [io size 0x0010]
[ 2.730000] pci 0000:02:00.0: BAR 4: failed to assign [io size 0x0010]
[ 2.740000] pci 0000:02:00.0: BAR 0: no space for [io size 0x0008]
[ 2.750000] pci 0000:02:00.0: BAR 0: failed to assign [io size 0x0008]
[ 2.770000] pci 0000:02:00.0: BAR 2: no space for [io size 0x0008]
[ 2.780000] pci 0000:02:00.0: BAR 2: failed to assign [io size 0x0008]
[ 2.790000] pci 0000:02:00.0: BAR 1: no space for [io size 0x0004]
[ 2.800000] pci 0000:02:00.0: BAR 1: failed to assign [io size 0x0004]
[ 2.820000] pci 0000:02:00.0: BAR 3: no space for [io size 0x0004]
[ 2.830000] pci 0000:02:00.0: BAR 3: failed to assign [io size 0x0004]
[ 2.840000] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 2.850000] pci 0000:03:00.0: BAR 5: no space for [mem size 0x00000200]
[ 2.860000] pci 0000:03:00.0: BAR 5: failed to assign [mem size 0x00000200]
[ 2.880000] pci 0000:03:00.0: BAR 4: no space for [io size 0x0010]
[ 2.890000] pci 0000:03:00.0: BAR 4: failed to assign [io size 0x0010]
[ 2.900000] pci 0000:03:00.0: BAR 0: no space for [io size 0x0008]
[ 2.910000] pci 0000:03:00.0: BAR 0: failed to assign [io size 0x0008]
[ 2.930000] pci 0000:03:00.0: BAR 2: no space for [io size 0x0008]
[ 2.940000] pci 0000:03:00.0: BAR 2: failed to assign [io size 0x0008]
[ 2.950000] pci 0000:03:00.0: BAR 1: no space for [io size 0x0004]
[ 2.970000] pci 0000:03:00.0: BAR 1: failed to assign [io size 0x0004]
[ 2.980000] pci 0000:03:00.0: BAR 3: no space for [io size 0x0004]
[ 2.990000] pci 0000:03:00.0: BAR 3: failed to assign [io size 0x0004]
[ 3.000000] pci 0000:00:02.0: PCI bridge to [bus 03]
[ 3.080000] SCSI subsystem initialized
[ 3.090000] libata version 3.00 loaded.
[ 3.100000] random: fast init done
[ 3.100000] clocksource: Switched to clocksource GIC
[ 3.130000] NET: Registered protocol family 2
[ 3.140000] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144
bytes)
[ 3.150000] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 3.170000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 3.180000] TCP: Hash tables configured (established 4096 bind 4096)
[ 3.190000] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 3.200000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 3.220000] NET: Registered protocol family 1
[ 3.230000] PCI: CLS 0 bytes, default 32
[ 8.200000] Initialise system trusted keyrings
[ 8.210000] workingset: timestamp_bits=30 max_order=17 bucket_order=0
[ 8.340000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 8.350000] jffs2: version 2.2. (NAND) (SUMMARY) \xffffffc2\xffffffa9
2001-2006 Red Hat, Inc.
[ 8.380000] SGI XFS with security attributes, no debug enabled
[ 8.430000] Key type asymmetric registered
[ 8.440000] Asymmetric key parser 'x509' registered
[ 8.450000] bounce: pool size: 64 pages
[ 8.450000] io scheduler noop registered
[ 8.460000] io scheduler deadline registered (default)
[ 8.470000] io scheduler mq-deadline registered (default)
[ 8.480000] io scheduler kyber registered
[ 8.500000] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 8.520000] console [ttyS0] disabled
[ 8.530000] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 18, base_baud
= 3125000) is a 16550A
[ 8.550000] console [ttyS0] enabled
[ 8.560000] bootconsole [early0] disabled
[ 8.580000] cacheinfo: Failed to find cpu0 device node
[ 8.590000] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 8.670000] loop: module loaded
[ 8.680000] ahci 0000:01:00.0: version 3.0
[ 8.680000] ahci: probe of 0000:01:00.0 failed with error -22
[ 8.700000] ahci: probe of 0000:02:00.0 failed with error -22
[ 8.710000] ahci: probe of 0000:03:00.0 failed with error -22
[ 8.720000] libphy: Fixed MDIO Bus: probed
[ 8.730000] tun: Universal TUN/TAP device driver, 1.6
[ 8.750000] sdhci: Secure Digital Host Controller Interface driver
[ 8.760000] sdhci: Copyright(c) Pierre Ossman
[ 8.770000] spi-mt7621 1e000b00.spi: sys_freq: 225000000
[ 8.780000] m25p80 spi0.0: w25q256 (32768 Kbytes)
[ 8.790000] 4 fixed-partitions partitions found on MTD device spi0.0
[ 8.810000] Creating 4 MTD partitions on "spi0.0":
[ 8.820000] 0x000000000000-0x000000030000 : "u-boot"
[ 8.830000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 8.850000] 0x000000040000-0x000000050000 : "factory"
[ 8.870000] 0x000000050000-0x000002000000 : "firmware"
[ 8.940000] libphy: mdio: probed
[ 8.970000] mtk_soc_eth 1e100000.ethernet: generated random MAC address
6e:14:15:9c:55:5b
[ 8.990000] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at
0xbe100000, irq 21
[ 9.020000] NET: Registered protocol family 10
[ 9.040000] Segment Routing with IPv6
[ 9.050000] NET: Registered protocol family 17
[ 9.060000] 8021q: 802.1Q VLAN Support v1.8
[ 9.070000] Loading compiled-in X.509 certificates
[ 9.090000] hctosys: unable to open rtc device (rtc0)
[ 9.120000] Freeing unused kernel memory: 6524K
[ 9.130000] This architecture does not have kernel memory protection.
[ 9.170000] mmc0: new high speed SD card at address 0002
[ 9.190000] mmcblk0: mmc0:0002 00000 1.88 GiB
[ 9.380000] usbcore: registered new interface driver usbfs
[ 9.400000] usbcore: registered new interface driver hub
[ 9.420000] usbcore: registered new device driver usb
[ 9.530000] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 9.540000] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus
number 1
[ 9.570000] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96
quirks 0x0000000000210010
[ 9.590000] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000
[ 9.630000] hub 1-0:1.0: USB hub found
[ 9.630000] hub 1-0:1.0: 2 ports detected
[ 9.660000] xhci-mtk 1e1c0000.xhci: xHCI Host Controller
[ 9.670000] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus
number 2
[ 9.680000] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed
[ 9.700000] usb usb2: We don't know the algorithms for LPM for this host,
disabling LPM.
[ 9.740000] hub 2-0:1.0: USB hub found
[ 9.740000] hub 2-0:1.0: 1 port detected
[ 9.810000] usbcore: registered new interface driver usb-storage
signature.asc
Description: PGP signature
_______________________________________________ devel mailing list de...@linuxdriverproject.org http://driverdev.linuxdriverproject.org/mailman/listinfo/driverdev-devel
