Searching the web, I came up with numerous ..."fixes"... , some benign, some disastrous.
The consensus though is that it was caused by a Microsoft Security Update and we can only wait for the next Update to fix the Previous Update. In the meantime, it's a minor PITA that does no damage, so I just need to remember to open DXBase twice !! 73, Dick, W1KSZ On Thu, Sep 13, 2012 at 10:46 AM, Richard Solomon <dickw1...@gmail.com> wrote: > OK, so what can I do about it ?? > > 73, Dick, W1KSZ > > On Thu, Sep 13, 2012 at 10:35 AM, Neal Campbell <nealk...@me.com> wrote: >> I think the technical term is that windows is "hosed up"! >> >> 73 >> Neal >> On Sep 13, 2012, at 12:48 PM, Jack <lenn...@bellsouth.net> wrote: >> >>> Dick, >>> >>> No, I do not think DXbase is corrupt. I actually think that you did way too >>> many "new" things .... brand new home built pc, two software packages >>> recently installed, probably a lot of new drivers to go with you new pc... >>> any one of these things could be causing the problem. >>> >>> But, a quick search on the web reveals this info and there is a ton of other >>> information about this same error message as well. >>> >>> http://forums.cnet.com/7723-6142_102-243141/exception-processing-message-c00 >>> 00013/ >>> >>> Good luck. >>> Jack >>> >>> >>> -----Original Message----- >>> From: dxbase-boun...@mailman.qth.net [mailto:dxbase-boun...@mailman.qth.net] >>> On Behalf Of Richard Solomon >>> Sent: Thursday, September 13, 2012 12:09 PM >>> To: dxbase@mailman.qth.net >>> Subject: [Dxbase] New Problem >>> >>> I am running Ver.1.05 and all was well until I moved computers around !! >>> >>> I built a new Windows 7 Machine and replaced my everyday computer with it. >>> I moved that Computer into the shack. Now, it already had DXBase 2007 on it >>> and it was working. >>> >>> After installing Ham Radio Deluxe and the SignaLink interface and some other >>> stuff I noticed this problem. >>> >>> When I tried to enter a Call I get the following error message: >>> >>> Windows - No Disk >>> Exception Processing Message C0000013 Parameters 75b6bf7c 4 (then the 75b >>> message repeated twice. >>> >>> If I clear that error message I get: >>> >>> Windows - No Disk >>> There is no disk in the drive. Please insert Disk into Drive. >>> >>> If I clear that message, close DXBase and re-open it, all is well. BUT, if I >>> change Databases the above errors repeat themselves. >>> >>> Can my copy of the DXBase program be corrupt ?? >>> >>> Thanks for any help, >>> >>> 73, Dick, W1KSZ >>> ______________________________________________________________ >>> Dxbase mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/dxbase >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Dxbase@mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> >>> ______________________________________________________________ >>> Dxbase mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/dxbase >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Dxbase@mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >> ______________________________________________________________ Dxbase mailing list Home: http://mailman.qth.net/mailman/listinfo/dxbase Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Dxbase@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
