Thanks Fred! What a PITA.
On Wed, Jun 19, 2019 at 7:43 AM -0800, "Fred Handscombe" <[email protected]> wrote:
You have to get a new registration file with ALL the callsigns in it, or
just put the registered call in the field as it serves no other purpose
anyway, you need 1 log file per on the air callsign.
I have one with 5 or 6 of my personal calls in various countries
I had many robust discussions with Jack on the subject but he wouldn’t
budge!
73 Fred
G4BWP
www.g4bwp.com
Hoarder of fine valved radios
------ Original Message ------
From: "Bill - KL7TC"
To: "Fred Handscombe" ; [email protected]
Sent: 19/06/2019 16:18:38
Subject: Re: Re[2]: [Dxbase] Selection Wizard Issue...again
>Well that's lame because what happens if you had 2 callsigns?
>
>
>
>
>On Wed, Jun 19, 2019 at 6:58 AM -0800, "Fred Handscombe"
> wrote:
>
>>If the Opr Call is not the registered one then DXbase will not export
>>any contacts
>>
>>If you "find and replace" the Opr Call with the registered one through
>>the whole log then it will work for you
>>
>>The registered Opr Call was Jack's original way of stopping bootleggers
>>
>>73 Fred
>>G4BWP
>>
>>www.g4bwp.com
>>Hoarder of fine valved radios
>>
>>------ Original Message ------
>>From: "Bill - KL7TC"
>>To: "Fred Handscombe" ; [email protected]
>>Sent: 19/06/2019 15:02:11
>>Subject: Re: [Dxbase] Selection Wizard Issue...again
>>
>> >It is different
>> >
>> >
>> >
>> >
>> >On Tue, Jun 18, 2019 at 11:32 PM -0800, "Fred Handscombe"
>> > wrote:
>> >
>> >>Bill
>> >>
>> >>Does the Opr Call in his log match the registered callsign?
>> >>
>> >>You can check in Help > About...
>> >>
>> >>That is the cause of many problems in DXbase
>> >>
>> >>I can confirm that the Selection Wizard with no tick marks in the QSO
>> >>Filters page WILL export the entire log under Windows 10
>> >>
>> >>73 Fred
>> >>G4BWP
>> >>
>> >>www.g4bwp.com
>> >>Hoarder of fine valved radios
>> >>
>> >>------ Original Message ------
>> >>From: "Bill - KL7TC"
>> >>To: "[email protected]"
>> >>Sent: 19/06/2019 07:34:01
>> >>Subject: [Dxbase] Selection Wizard Issue...again
>> >>
>> >> >Trying to export my dad’s 2007 log to adif using the selection wizard.
>> >> >I have used it in the past on mine with no issues.
>> >> >
>> >> >1. No checks blocks
>> >> >2. Tried test first and no test, nothing happens.
>> >> >3. When I click start, it opens the location and when hit ok, nothing
>> >> >happens.
>> >> >
>> >> >I was trying it at his house and mine with same result…nothing. There
>> >> >are 2373 qsos in the log.
>> >> >
>> >> >Not sure what the issue is…unless it’s a Windows 10 issue.
>> >> >
>> >> >Thanks and 73,
>> >> >Bill – KL7TC
>> >> >Fairbanks, Alaska BP64DU
>> >> >
>> >> >
>> >> >Sent from Mail for Windows 10
>> >> >
>> >> >______________________________________________________________
>> >> >Dxbase mailing list
>> >> >Home: http://mailman.qth.net/mailman/listinfo/dxbase
>> >> >Help: http://mailman.qth.net/mmfaq.htm
>> >> >Post: mailto:[email protected]
>> >> >
>> >> >This list hosted by: http://www.qsl.net
>> >> >Please help support this email list: http://www.qsl.net/donate.html
>> >>
>> >>
>>
>>
______________________________________________________________
Dxbase mailing list
Home: http://mailman.qth.net/mailman/listinfo/dxbase
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:[email protected]
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
