All we did was the equivalent of 'ifup eth3'. We are not using network manager.
Can you point me to some documentation on this 'ies api based application'? Thanks, Ben On 11/02/2017 10:17 AM, Kwan, Ngai-mint wrote:
Hi Ben, From your ethtool output, I can see that you have: Link detected: no From past experiences, this means that you're not running an IES API based application to manage the card. Can you confirm that you have or don't have an application manager running? Regards, Ngai-Mint Kwan -----Original Message----- From: Ben Greear [mailto:gree...@candelatech.com] Sent: Monday, October 30, 2017 3:12 PM To: e1000-devel list <e1000-devel@lists.sourceforge.net> Subject: [E1000-devel] fm10k cannot get link Hello, We're trying to get an Intel 100G NIC to work, and so far, cannot get it to link. The cable is: X0016I4AO3 QSFP28 10Gtek (any suggestions for a better/different one?) [ 5.022681] fm10k 0000:05:00.0: PCI Express bandwidth of 64GT/s available [ 5.022683] fm10k 0000:05:00.0: (Speed:8.0GT/s, Width: x8, Encoding Loss:<2%, Payload:256B) [ 5.022684] fm10k 0000:05:00.0: 00:e0:ed:54:78:f2 [ 5.027864] fm10k 0000:06:00.0: PCI Express bandwidth of 64GT/s available [ 5.027865] fm10k 0000:06:00.0: (Speed:8.0GT/s, Width: x8, Encoding Loss:<2%, Payload:256B) [ 5.027866] fm10k 0000:06:00.0: 00:e0:ed:54:78:f3 [ 6.057950] Modules linked in: ioatdma(+) shpchp nfsd auth_rpcgss nfs_acl lockd grace sunrpc ast drm_kms_helper ttm igb drm i2c_algo_bit i2c_core ixgbe mdio hwmon fm10k ptp pps_core dca fjes ipv6 crc_ccitt [ 7.294441] fm10k 0000:05:00.0 eth0.r: renamed from eth0 [ 14.044914] fm10k 0000:05:00.0 eth2: renamed from eth0.r [ 14.107798] fm10k 0000:06:00.0 eth1.r: renamed from eth1 [ 14.178217] fm10k 0000:06:00.0 eth3: renamed from eth1.r [root@lf1005c-is14120020 ~]# ethtool eth3 Settings for eth3: Current message level: 0x00000007 (7) drv probe link Link detected: no [root@lf1005c-is14120020 ~]# uname -a Linux lf1005c-is14120020 4.9.29+ #46 SMP PREEMPT Wed Jul 26 17:48:57 PDT 2017 x86_64 x86_64 x86_64 GNU/Linux [root@lf1005c-is14120020 ~]# ethtool -i eth3 driver: fm10k version: 0.21.2-k firmware-version: bus-info: 0000:06:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: no supports-register-dump: yes supports-priv-flags: no [root@lf1005c-is14120020 ~]# lspci|grep 06 06:00.0 Ethernet controller: Intel Corporation Device 15a4 Please let me know if you have any suggestions. Thanks, Ben -- Ben Greear <gree...@candelatech.com> Candela Technologies Inc http://www.candelatech.com ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ E1000-devel mailing list E1000-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/e1000-devel To learn more about Intel® Ethernet, visit http://communities.intel.com/community/wired
-- Ben Greear <gree...@candelatech.com> Candela Technologies Inc http://www.candelatech.com ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ E1000-devel mailing list E1000-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/e1000-devel To learn more about Intel® Ethernet, visit http://communities.intel.com/community/wired
