Hi, the card came back and I had to flash it again but it worked perfectly fine this time :) So I setup a new Kernel (3.18.20) and the most recent i40e driver (1.3.39.1) and removed the previous workaround to disable ntuples on both interfaces. So basically a vanilla setup. That host is up for several hours no and there was no spam so far and only one reset yet: Sep 25 12:38:54 somehost kernel: [77571.409182] i40e 0000:02:00.1: TX driver issue detected, PF reset issued Sep 25 12:38:55 somehost kernel: [77572.245943] bond0: link status up again after 0 ms for interface eth1
and here's the requested dmesg again: [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.18.20 (fud@somehost) (gcc version 4.7.2 (Debian 4.7.2-5) ) #1 SMP Wed Aug 26 14:25:15 CEST 2015 [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.18.20 root=UUID=ea7a13a2-a96b-4165-801a-119b0f0d9b8f ro ipv6.disable=1 intel_pstate=disable earlyprintk=ttyS0,115200,keep intel_iommu=off [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000099bff] usable [ 0.000000] BIOS-e820: [mem 0x0000000000099c00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000becc8fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000becc9000-0x00000000bed0bfff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000bed0c000-0x00000000ce491fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000ce492000-0x00000000ce534fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ce535000-0x00000000ce5c6fff] usable [ 0.000000] BIOS-e820: [mem 0x00000000ce5c7000-0x00000000ce68bfff] ACPI NVS [ 0.000000] BIOS-e820: [mem 0x00000000ce68c000-0x00000000cf7fefff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000cf7ff000-0x00000000cf7fffff] usable [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000082fffffff] usable [ 0.000000] console [earlyser0] enabled [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] SMBIOS 2.7 present. [ 0.000000] DMI: Supermicro X9SCL/X9SCM/X9SCL/X9SCM, BIOS 2.2 02/20/2015 [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable [ 0.000000] AGP: No AGP bridge found [ 0.000000] e820: last_pfn = 0x830000 max_arch_pfn = 0x400000000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-CBFFF write-protect [ 0.000000] CC000-E7FFF uncachable [ 0.000000] E8000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask 800000000 write-back [ 0.000000] 1 base 800000000 mask FE0000000 write-back [ 0.000000] 2 base 820000000 mask FF0000000 write-back [ 0.000000] 3 base 0E0000000 mask FE0000000 uncachable [ 0.000000] 4 base 0D0000000 mask FF0000000 uncachable [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] 8 disabled [ 0.000000] 9 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] e820: update [mem 0xd0000000-0xffffffff] usable ==> reserved [ 0.000000] e820: last_pfn = 0xcf800 max_arch_pfn = 0x400000000 [ 0.000000] found SMP MP-table at [mem 0x000fd7b0-0x000fd7bf] mapped at [ffff8800000fd7b0] [ 0.000000] Base memory trampoline at [ffff880000093000] 93000 size 24576 [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff] [ 0.000000] [mem 0x00000000-0x000fffff] page 4k [ 0.000000] BRK [0x01b02000, 0x01b02fff] PGTABLE [ 0.000000] BRK [0x01b03000, 0x01b03fff] PGTABLE [ 0.000000] BRK [0x01b04000, 0x01b04fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x82fe00000-0x82fffffff] [ 0.000000] [mem 0x82fe00000-0x82fffffff] page 2M [ 0.000000] BRK [0x01b05000, 0x01b05fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0x82c000000-0x82fdfffff] [ 0.000000] [mem 0x82c000000-0x82fdfffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x800000000-0x82bffffff] [ 0.000000] [mem 0x800000000-0x82bffffff] page 2M [ 0.000000] init_memory_mapping: [mem 0x00100000-0xbecc8fff] [ 0.000000] [mem 0x00100000-0x001fffff] page 4k [ 0.000000] [mem 0x00200000-0xbebfffff] page 2M [ 0.000000] [mem 0xbec00000-0xbecc8fff] page 4k [ 0.000000] init_memory_mapping: [mem 0xbed0c000-0xce491fff] [ 0.000000] [mem 0xbed0c000-0xbedfffff] page 4k [ 0.000000] [mem 0xbee00000-0xce3fffff] page 2M [ 0.000000] [mem 0xce400000-0xce491fff] page 4k [ 0.000000] BRK [0x01b06000, 0x01b06fff] PGTABLE [ 0.000000] BRK [0x01b07000, 0x01b07fff] PGTABLE [ 0.000000] init_memory_mapping: [mem 0xce535000-0xce5c6fff] [ 0.000000] [mem 0xce535000-0xce5c6fff] page 4k [ 0.000000] init_memory_mapping: [mem 0xcf7ff000-0xcf7fffff] [ 0.000000] [mem 0xcf7ff000-0xcf7fffff] page 4k [ 0.000000] init_memory_mapping: [mem 0x100000000-0x7ffffffff] [ 0.000000] [mem 0x100000000-0x7ffffffff] page 2M [ 0.000000] RAMDISK: [mem 0x360c0000-0x37057fff] [ 0.000000] ACPI: Early table checksum verification disabled [ 0.000000] ACPI: RSDP 0x00000000000F0490 000024 (v02 SUPERM) [ 0.000000] ACPI: XSDT 0x00000000CE64F088 00008C (v01 SUPERM SMCI--MB 00000001 AMI 00010013) [ 0.000000] ACPI: FACP 0x00000000CE65A210 00010C (v05 SUPERM SMCI--MB 00000001 AMI 00010013) [ 0.000000] ACPI: DSDT 0x00000000CE64F1A8 00B068 (v02 SUPERM SMCI--MB 00000000 INTL 20051117) [ 0.000000] ACPI: FACS 0x00000000CE68A080 000040 [ 0.000000] ACPI: APIC 0x00000000CE65A320 000092 (v03 SUPERM SMCI--MB 00000001 AMI 00010013) [ 0.000000] ACPI: FPDT 0x00000000CE65A3B8 000044 (v01 SUPERM SMCI--MB 00000001 AMI 00010013) [ 0.000000] ACPI: MCFG 0x00000000CE65A400 00003C (v01 SUPERM SMCI--MB 00000001 MSFT 00000097) [ 0.000000] ACPI: HPET 0x00000000CE65A440 000038 (v01 SUPERM SMCI--MB 00000001 AMI. 00000005) [ 0.000000] ACPI: SSDT 0x00000000CE65A478 000397 (v01 SataRe SataTabl 00001000 INTL 20091112) [ 0.000000] ACPI: SPMI 0x00000000CE65A810 000040 (v05 A M I OEMSPMI 00000000 AMI. 00000000) [ 0.000000] ACPI: SSDT 0x00000000CE65A850 0009A4 (v01 PmRef Cpu0Ist 00003000 INTL 20051117) [ 0.000000] ACPI: SSDT 0x00000000CE65B1F8 000B18 (v01 PmRef CpuPm 00003000 INTL 20051117) [ 0.000000] ACPI: EINJ 0x00000000CE65BD10 000130 (v01 AMI AMI EINJ 00000000 00000000) [ 0.000000] ACPI: ERST 0x00000000CE65BE40 000210 (v01 AMIER AMI ERST 00000000 00000000) [ 0.000000] ACPI: HEST 0x00000000CE65C050 0000A8 (v01 AMI AMI HEST 00000000 00000000) [ 0.000000] ACPI: BERT 0x00000000CE65C0F8 000030 (v01 AMI AMI BERT 00000000 00000000) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000082fffffff] [ 0.000000] NODE_DATA(0) allocated [mem 0x82ffdc000-0x82ffdffff] [ 0.000000] [ffffea0000000000-ffffea001cbfffff] PMD -> [ffff88080f600000-ffff88082b7fffff] on node 0 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00001000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0x82fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00001000-0x00098fff] [ 0.000000] node 0: [mem 0x00100000-0xbecc8fff] [ 0.000000] node 0: [mem 0xbed0c000-0xce491fff] [ 0.000000] node 0: [mem 0xce535000-0xce5c6fff] [ 0.000000] node 0: [mem 0xcf7ff000-0xcf7fffff] [ 0.000000] node 0: [mem 0x100000000-0x82fffffff] [ 0.000000] Initmem setup node 0 [mem 0x00001000-0x82fffffff] [ 0.000000] On node 0 totalpages: 8381562 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 21 pages reserved [ 0.000000] DMA zone: 3992 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 11498 pages used for memmap [ 0.000000] DMA32 zone: 840930 pages, LIFO batch:31 [ 0.000000] Normal zone: 103040 pages used for memmap [ 0.000000] Normal zone: 7536640 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x05] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000 [ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff] [ 0.000000] PM: Registered nosave memory: [mem 0x00099000-0x00099fff] [ 0.000000] PM: Registered nosave memory: [mem 0x0009a000-0x0009ffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff] [ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff] [ 0.000000] PM: Registered nosave memory: [mem 0xbecc9000-0xbed0bfff] [ 0.000000] PM: Registered nosave memory: [mem 0xce492000-0xce534fff] [ 0.000000] PM: Registered nosave memory: [mem 0xce5c7000-0xce68bfff] [ 0.000000] PM: Registered nosave memory: [mem 0xce68c000-0xcf7fefff] [ 0.000000] PM: Registered nosave memory: [mem 0xcf800000-0xdfffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfebfffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff] [ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff] [ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff] [ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff] [ 0.000000] e820: [mem 0xcf800000-0xdfffffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:8 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88082fc00000 s80960 r8192 d29632 u262144 [ 0.000000] pcpu-alloc: s80960 r8192 d29632 u262144 alloc=1*2097152 [ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 8266947 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.18.20 root=UUID=ea7a13a2-a96b-4165-801a-119b0f0d9b8f ro ipv6.disable=1 intel_pstate=disable earlyprintk=ttyS0,115200,keep intel_iommu=off [ 0.000000] Intel-IOMMU: disabled [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340 using standard form [ 0.000000] AGP: Checking aperture... [ 0.000000] AGP: No AGP bridge found [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing! [ 0.000000] Memory: 32970712K/33526248K available (5512K kernel code, 966K rwdata, 1832K rodata, 1228K init, 852K bss, 555536K reserved) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled. [ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=8. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 [ 0.000000] NR_IRQS:33024 nr_irqs:488 0 [ 0.000000] Console: colour VGA+ 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] allocated 134217728 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] hpet clockevent registered [ 0.000000] tsc: Fast TSC calibration failed [ 0.000000] tsc: PIT calibration matches HPET. 1 loops [ 0.000000] tsc: Detected 3499.669 MHz processor [ 0.000025] Calibrating delay loop (skipped), value calculated using timer frequency.. 6999.33 BogoMIPS (lpj=13998676) [ 0.010617] pid_max: default: 32768 minimum: 301 [ 0.015230] ACPI: Core revision 20140926 [ 0.024681] ACPI: All ACPI Tables successfully acquired [ 0.039606] Security Framework initialized [ 0.043611] AppArmor: AppArmor disabled by boot time parameter [ 0.049421] Yama: becoming mindful. [ 0.054266] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes) [ 0.067119] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes) [ 0.076825] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.083636] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.091133] Initializing cgroup subsys memory [ 0.095401] Initializing cgroup subsys devices [ 0.099824] Initializing cgroup subsys freezer [ 0.104249] Initializing cgroup subsys net_cls [ 0.108676] Initializing cgroup subsys blkio [ 0.112929] Initializing cgroup subsys perf_event [ 0.117615] Initializing cgroup subsys net_prio [ 0.122145] CPU: Physical Processor ID: 0 [ 0.126120] CPU: Processor Core ID: 0 [ 0.129769] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' [ 0.129769] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8) [ 0.143037] mce: CPU supports 9 MCE banks [ 0.146959] CPU0: Thermal monitoring enabled (TM1) [ 0.151728] process: using mwait in idle threads [ 0.156328] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 8 [ 0.156328] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32, 1GB 0 [ 0.168125] Freeing SMP alternatives memory: 20K (ffffffff81a26000 - ffffffff81a2b000) [ 0.176733] ftrace: allocating 22083 entries in 87 pages [ 0.197324] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.242968] smpboot: CPU0: Intel(R) Xeon(R) CPU E3-1270 V2 @ 3.50GHz (fam: 06, model: 3a, stepping: 09) [ 0.252247] TSC deadline timer enabled [ 0.252264] Performance Events: PEBS fmt1+, 16-deep LBR, IvyBridge events, full-width counters, Intel PMU driver. [ 0.262484] ... version: 3 [ 0.266477] ... bit width: 48 [ 0.270555] ... generic registers: 4 [ 0.274548] ... value mask: 0000ffffffffffff [ 0.279843] ... max period: 0000ffffffffffff [ 0.285137] ... fixed-purpose events: 3 [ 0.289130] ... event mask: 000000070000000f [ 0.295409] x86: Booting SMP configuration: [ 0.299494] .... node #0, CPUs: #1 [ 0.316534] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter. [ 0.324669] #2 #3 #4 #5 #6 #7 [ 0.407240] x86: Booted up 1 node, 8 CPUs [ 0.411319] smpboot: Total of 8 processors activated (55994.70 BogoMIPS) [ 0.424047] devtmpfs: initialized [ 0.430926] PM: Registering ACPI NVS region [mem 0xbecc9000-0xbed0bfff] (274432 bytes) [ 0.438777] PM: Registering ACPI NVS region [mem 0xce5c7000-0xce68bfff] (806912 bytes) [ 0.447304] pinctrl core: initialized pinctrl subsystem [ 0.452519] NET: Registered protocol family 16 [ 0.468890] cpuidle: using governor ladder [ 0.488929] cpuidle: using governor menu [ 0.492803] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.500309] ACPI: bus type PCI registered [ 0.504301] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 [ 0.510784] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000) [ 0.520010] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820 [ 0.526980] PCI: Using configuration type 1 for base access [ 0.544821] ACPI: Added _OSI(Module Device) [ 0.548905] ACPI: Added _OSI(Processor Device) [ 0.553330] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.558017] ACPI: Added _OSI(Processor Aggregator Device) [ 0.565243] ACPI: Executed 1 blocks of module-level executable AML code [ 0.739624] \_SB_:_OSC invalid UUID [ 0.739625] _OSC request data:1 1f [ 0.739811] ACPI: Dynamic OEM Table Load: [ 0.743707] ACPI: SSDT 0xFFFF880807B5C000 00083B (v01 PmRef Cpu0Cst 00003001 INTL 20051117) [ 0.764280] ACPI: Dynamic OEM Table Load: [ 0.768173] ACPI: SSDT 0xFFFF880807049C00 000303 (v01 PmRef ApIst 00003000 INTL 20051117) [ 0.788649] ACPI: Dynamic OEM Table Load: [ 0.792543] ACPI: SSDT 0xFFFF880807007C00 000119 (v01 PmRef ApCst 00003000 INTL 20051117) [ 0.813761] ACPI: Interpreter enabled [ 0.817329] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140926/hwxface-580) [ 0.826523] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20140926/hwxface-580) [ 0.835727] ACPI: (supports S0 S1 S4 S5) [ 0.839628] ACPI: Using IOAPIC for interrupt routing [ 0.844615] HEST: Table parsing has been initialized. [ 0.849610] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.863689] ACPI: Power Resource [FN00] (off) [ 0.868006] ACPI: Power Resource [FN01] (off) [ 0.872344] ACPI: Power Resource [FN02] (off) [ 0.876682] ACPI: Power Resource [FN03] (off) [ 0.881022] ACPI: Power Resource [FN04] (off) [ 0.885681] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe]) [ 0.891767] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI] [ 0.900002] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug PME] [ 0.907216] acpi PNP0A08:00: _OSC: OS now controls [AER PCIeCapability] [ 0.914173] PCI host bridge to bus 0000:00 [ 0.918169] pci_bus 0000:00: root bus resource [bus 00-fe] [ 0.923636] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7] [ 0.929798] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff] [ 0.935959] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff] [ 0.942817] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff] [ 0.949673] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff] [ 0.956530] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff] [ 0.963386] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff] [ 0.970243] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff] [ 0.977101] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff] [ 0.983957] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff] [ 0.990814] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xfeafffff] [ 0.997674] pci 0000:00:00.0: [8086:0158] type 00 class 0x060000 [ 0.997751] pci 0000:00:01.0: [8086:0151] type 01 class 0x060400 [ 0.997831] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold [ 0.997870] pci 0000:00:01.0: System wakeup disabled by ACPI [ 1.003450] pci 0000:00:01.1: [8086:0155] type 01 class 0x060400 [ 1.003473] pci 0000:00:01.1: PME# supported from D0 D3hot D3cold [ 1.003502] pci 0000:00:01.1: System wakeup disabled by ACPI [ 1.009121] pci 0000:00:19.0: [8086:1502] type 00 class 0x020000 [ 1.009138] pci 0000:00:19.0: reg 0x10: [mem 0xdfb00000-0xdfb1ffff] [ 1.009145] pci 0000:00:19.0: reg 0x14: [mem 0xdfb25000-0xdfb25fff] [ 1.009153] pci 0000:00:19.0: reg 0x18: [io 0xf020-0xf03f] [ 1.009212] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold [ 1.009246] pci 0000:00:19.0: System wakeup disabled by ACPI [ 1.014835] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320 [ 1.014854] pci 0000:00:1a.0: reg 0x10: [mem 0xdfb24000-0xdfb243ff] [ 1.014938] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold [ 1.014983] pci 0000:00:1a.0: System wakeup disabled by ACPI [ 1.020571] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400 [ 1.020648] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 1.020686] pci 0000:00:1c.0: System wakeup disabled by ACPI [ 1.026274] pci 0000:00:1c.4: [8086:1c18] type 01 class 0x060400 [ 1.026351] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold [ 1.026388] pci 0000:00:1c.4: System wakeup disabled by ACPI [ 1.031981] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320 [ 1.032000] pci 0000:00:1d.0: reg 0x10: [mem 0xdfb23000-0xdfb233ff] [ 1.032084] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold [ 1.032129] pci 0000:00:1d.0: System wakeup disabled by ACPI [ 1.037718] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401 [ 1.037791] pci 0000:00:1e.0: System wakeup disabled by ACPI [ 1.043379] pci 0000:00:1f.0: [8086:1c52] type 00 class 0x060100 [ 1.043532] pci 0000:00:1f.2: [8086:1c02] type 00 class 0x010601 [ 1.043549] pci 0000:00:1f.2: reg 0x10: [io 0xf070-0xf077] [ 1.043556] pci 0000:00:1f.2: reg 0x14: [io 0xf060-0xf063] [ 1.043563] pci 0000:00:1f.2: reg 0x18: [io 0xf050-0xf057] [ 1.043570] pci 0000:00:1f.2: reg 0x1c: [io 0xf040-0xf043] [ 1.043577] pci 0000:00:1f.2: reg 0x20: [io 0xf000-0xf01f] [ 1.043584] pci 0000:00:1f.2: reg 0x24: [mem 0xdfb22000-0xdfb227ff] [ 1.043625] pci 0000:00:1f.2: PME# supported from D3hot [ 1.043684] pci 0000:00:1f.3: [8086:1c22] type 00 class 0x0c0500 [ 1.043697] pci 0000:00:1f.3: reg 0x10: [mem 0xdfb21000-0xdfb210ff 64bit] [ 1.043716] pci 0000:00:1f.3: reg 0x20: [io 0x0580-0x059f] [ 1.043832] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.048735] pci 0000:02:00.0: [8086:1572] type 00 class 0x020000 [ 1.048745] pci 0000:02:00.0: reg 0x10: [mem 0xdd800000-0xddffffff 64bit pref] [ 1.048755] pci 0000:02:00.0: reg 0x1c: [mem 0xde808000-0xde80ffff 64bit pref] [ 1.048764] pci 0000:02:00.0: reg 0x30: [mem 0xdfa80000-0xdfafffff pref] [ 1.048800] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 1.048818] pci 0000:02:00.0: reg 0x184: [mem 0xde400000-0xde40ffff 64bit pref] [ 1.048827] pci 0000:02:00.0: reg 0x190: [mem 0xde910000-0xde913fff 64bit pref] [ 1.048862] pci 0000:02:00.1: [8086:1572] type 00 class 0x020000 [ 1.048872] pci 0000:02:00.1: reg 0x10: [mem 0xdd000000-0xdd7fffff 64bit pref] [ 1.048882] pci 0000:02:00.1: reg 0x1c: [mem 0xde800000-0xde807fff 64bit pref] [ 1.048891] pci 0000:02:00.1: reg 0x30: [mem 0xdfa00000-0xdfa7ffff pref] [ 1.048925] pci 0000:02:00.1: PME# supported from D0 D3hot D3cold [ 1.048942] pci 0000:02:00.1: reg 0x184: [mem 0xde000000-0xde00ffff 64bit pref] [ 1.048951] pci 0000:02:00.1: reg 0x190: [mem 0xde810000-0xde813fff 64bit pref] [ 1.056725] pci 0000:00:01.1: PCI bridge to [bus 02-03] [ 1.061856] pci 0000:00:01.1: bridge window [mem 0xdfa00000-0xdfafffff] [ 1.061858] pci 0000:00:01.1: bridge window [mem 0xdd000000-0xdeafffff 64bit pref] [ 1.061915] pci 0000:00:1c.0: PCI bridge to [bus 04] [ 1.066903] pci 0000:05:00.0: [8086:10d3] type 00 class 0x020000 [ 1.066942] pci 0000:05:00.0: reg 0x10: [mem 0xdf900000-0xdf91ffff] [ 1.066987] pci 0000:05:00.0: reg 0x18: [io 0xe000-0xe01f] [ 1.067010] pci 0000:05:00.0: reg 0x1c: [mem 0xdf920000-0xdf923fff] [ 1.067239] pci 0000:05:00.0: PME# supported from D0 D3hot D3cold [ 1.067289] pci 0000:05:00.0: System wakeup disabled by ACPI [ 1.080881] pci 0000:00:1c.4: PCI bridge to [bus 05] [ 1.085759] pci 0000:00:1c.4: bridge window [io 0xe000-0xefff] [ 1.085762] pci 0000:00:1c.4: bridge window [mem 0xdf900000-0xdf9fffff] [ 1.085807] pci 0000:06:03.0: [102b:0532] type 00 class 0x030000 [ 1.085822] pci 0000:06:03.0: reg 0x10: [mem 0xdc000000-0xdcffffff pref] [ 1.085831] pci 0000:06:03.0: reg 0x14: [mem 0xdf800000-0xdf803fff] [ 1.085839] pci 0000:06:03.0: reg 0x18: [mem 0xdf000000-0xdf7fffff] [ 1.085948] pci 0000:00:1e.0: PCI bridge to [bus 06] (subtractive decode) [ 1.092645] pci 0000:00:1e.0: bridge window [mem 0xdf000000-0xdf8fffff] [ 1.092650] pci 0000:00:1e.0: bridge window [mem 0xdc000000-0xdcffffff 64bit pref] [ 1.092651] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode) [ 1.092652] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode) [ 1.092653] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode) [ 1.092655] pci 0000:00:1e.0: bridge window [mem 0x000cc000-0x000cffff] (subtractive decode) [ 1.092656] pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000d3fff] (subtractive decode) [ 1.092657] pci 0000:00:1e.0: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode) [ 1.092658] pci 0000:00:1e.0: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode) [ 1.092659] pci 0000:00:1e.0: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode) [ 1.092660] pci 0000:00:1e.0: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode) [ 1.092661] pci 0000:00:1e.0: bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode) [ 1.092662] pci 0000:00:1e.0: bridge window [mem 0xd0000000-0xfeafffff] (subtractive decode) [ 1.092690] acpi PNP0A08:00: Disabling ASPM (FADT indicates it is unsupported) [ 1.100314] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15) [ 1.107107] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 10 11 12 14 15) [ 1.113962] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 10 11 12 14 15) [ 1.120818] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 *11 12 14 15) [ 1.127675] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 10 11 12 14 15) [ 1.134531] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled. [ 1.142515] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled. [ 1.150505] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15) [ 1.157484] ACPI: Enabled 4 GPEs in block 00 to 3F [ 1.162221] vgaarb: setting as boot device: PCI:0000:06:03.0 [ 1.167794] vgaarb: device added: PCI:0000:06:03.0,decodes=io+mem,owns=io+mem,locks=none [ 1.175867] vgaarb: loaded [ 1.178556] vgaarb: bridge control possible 0000:06:03.0 [ 1.183909] PCI: Using ACPI for IRQ routing [ 1.193792] PCI: pci_cache_line_size set to 64 bytes [ 1.193833] e820: reserve RAM buffer [mem 0x00099c00-0x0009ffff] [ 1.193834] e820: reserve RAM buffer [mem 0xbecc9000-0xbfffffff] [ 1.193835] e820: reserve RAM buffer [mem 0xce492000-0xcfffffff] [ 1.193836] e820: reserve RAM buffer [mem 0xce5c7000-0xcfffffff] [ 1.193837] e820: reserve RAM buffer [mem 0xcf800000-0xcfffffff] [ 1.193935] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0 [ 1.199994] hpet0: 8 comparators, 64-bit 14.318180 MHz counter [ 1.207831] Switched to clocksource hpet [ 1.215086] pnp: PnP ACPI init [ 1.218096] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved [ 1.224641] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active) [ 1.224688] system 00:01: [io 0x0680-0x069f] has been reserved [ 1.230542] system 00:01: [io 0x1000-0x100f] has been reserved [ 1.236442] system 00:01: [io 0xffff] has been reserved [ 1.241736] system 00:01: [io 0xffff] has been reserved [ 1.247031] system 00:01: [io 0x0400-0x0453] could not be reserved [ 1.253282] system 00:01: [io 0x0458-0x047f] has been reserved [ 1.259182] system 00:01: [io 0x0500-0x057f] has been reserved [ 1.265084] system 00:01: [io 0x164e-0x164f] has been reserved [ 1.270987] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.271008] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active) [ 1.271039] system 00:03: [io 0x0454-0x0457] has been reserved [ 1.276891] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active) [ 1.276924] system 00:04: [io 0x04d0-0x04d1] has been reserved [ 1.282792] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.282868] system 00:05: [io 0x0a00-0x0a1f] has been reserved [ 1.288693] system 00:05: [io 0x0a30-0x0a3f] has been reserved [ 1.294594] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.294751] pnp 00:06: [dma 0 disabled] [ 1.294780] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 1.294921] pnp 00:07: [dma 0 disabled] [ 1.294947] pnp 00:07: Plug and Play ACPI device, IDs PNP0501 (active) [ 1.295019] system 00:08: [io 0x0b00-0x0b7f] has been reserved [ 1.300845] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.300958] pnp 00:09: [dma 0 disabled] [ 1.300985] pnp 00:09: Plug and Play ACPI device, IDs PNP0501 (active) [ 1.301064] pnp 00:0a: Plug and Play ACPI device, IDs IPI0001 (active) [ 1.301198] system 00:0b: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 1.307720] system 00:0b: [mem 0xfed10000-0xfed17fff] has been reserved [ 1.314314] system 00:0b: [mem 0xfed18000-0xfed18fff] has been reserved [ 1.320909] system 00:0b: [mem 0xfed19000-0xfed19fff] has been reserved [ 1.327506] system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved [ 1.334102] system 00:0b: [mem 0xfed20000-0xfed3ffff] has been reserved [ 1.340701] system 00:0b: [mem 0xfed90000-0xfed93fff] has been reserved [ 1.347295] system 00:0b: [mem 0xfed45000-0xfed8ffff] has been reserved [ 1.353892] system 00:0b: [mem 0xff000000-0xffffffff] has been reserved [ 1.360488] system 00:0b: [mem 0xfee00000-0xfeefffff] could not be reserved [ 1.367430] system 00:0b: [mem 0xd0000000-0xd0000fff] has been reserved [ 1.374027] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active) [ 1.374113] pnp: PnP ACPI: found 12 devices [ 1.384167] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.389053] pci 0000:00:01.1: PCI bridge to [bus 02-03] [ 1.394250] pci 0000:00:01.1: bridge window [mem 0xdfa00000-0xdfafffff] [ 1.401020] pci 0000:00:01.1: bridge window [mem 0xdd000000-0xdeafffff 64bit pref] [ 1.408745] pci 0000:00:1c.0: PCI bridge to [bus 04] [ 1.413701] pci 0000:00:1c.4: PCI bridge to [bus 05] [ 1.418641] pci 0000:00:1c.4: bridge window [io 0xe000-0xefff] [ 1.424718] pci 0000:00:1c.4: bridge window [mem 0xdf900000-0xdf9fffff] [ 1.431489] pci 0000:00:1e.0: PCI bridge to [bus 06] [ 1.436435] pci 0000:00:1e.0: bridge window [mem 0xdf000000-0xdf8fffff] [ 1.443203] pci 0000:00:1e.0: bridge window [mem 0xdc000000-0xdcffffff 64bit pref] [ 1.450929] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 1.450931] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 1.450932] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 1.450933] pci_bus 0000:00: resource 7 [mem 0x000cc000-0x000cffff] [ 1.450934] pci_bus 0000:00: resource 8 [mem 0x000d0000-0x000d3fff] [ 1.450935] pci_bus 0000:00: resource 9 [mem 0x000d4000-0x000d7fff] [ 1.450936] pci_bus 0000:00: resource 10 [mem 0x000d8000-0x000dbfff] [ 1.450937] pci_bus 0000:00: resource 11 [mem 0x000dc000-0x000dffff] [ 1.450938] pci_bus 0000:00: resource 12 [mem 0x000e0000-0x000e3fff] [ 1.450939] pci_bus 0000:00: resource 13 [mem 0x000e4000-0x000e7fff] [ 1.450940] pci_bus 0000:00: resource 14 [mem 0xd0000000-0xfeafffff] [ 1.450941] pci_bus 0000:02: resource 1 [mem 0xdfa00000-0xdfafffff] [ 1.450942] pci_bus 0000:02: resource 2 [mem 0xdd000000-0xdeafffff 64bit pref] [ 1.450943] pci_bus 0000:05: resource 0 [io 0xe000-0xefff] [ 1.450944] pci_bus 0000:05: resource 1 [mem 0xdf900000-0xdf9fffff] [ 1.450946] pci_bus 0000:06: resource 1 [mem 0xdf000000-0xdf8fffff] [ 1.450947] pci_bus 0000:06: resource 2 [mem 0xdc000000-0xdcffffff 64bit pref] [ 1.450948] pci_bus 0000:06: resource 4 [io 0x0000-0x0cf7] [ 1.450949] pci_bus 0000:06: resource 5 [io 0x0d00-0xffff] [ 1.450950] pci_bus 0000:06: resource 6 [mem 0x000a0000-0x000bffff] [ 1.450951] pci_bus 0000:06: resource 7 [mem 0x000cc000-0x000cffff] [ 1.450952] pci_bus 0000:06: resource 8 [mem 0x000d0000-0x000d3fff] [ 1.450953] pci_bus 0000:06: resource 9 [mem 0x000d4000-0x000d7fff] [ 1.450954] pci_bus 0000:06: resource 10 [mem 0x000d8000-0x000dbfff] [ 1.450955] pci_bus 0000:06: resource 11 [mem 0x000dc000-0x000dffff] [ 1.450956] pci_bus 0000:06: resource 12 [mem 0x000e0000-0x000e3fff] [ 1.450957] pci_bus 0000:06: resource 13 [mem 0x000e4000-0x000e7fff] [ 1.450958] pci_bus 0000:06: resource 14 [mem 0xd0000000-0xfeafffff] [ 1.451014] NET: Registered protocol family 2 [ 1.455462] TCP established hash table entries: 262144 (order: 9, 2097152 bytes) [ 1.463005] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 1.469713] TCP: Hash tables configured (established 262144 bind 65536) [ 1.476246] TCP: reno registered [ 1.479464] UDP hash table entries: 16384 (order: 7, 524288 bytes) [ 1.485680] UDP-Lite hash table entries: 16384 (order: 7, 524288 bytes) [ 1.492306] NET: Registered protocol family 1 [ 1.496818] PCI: CLS mismatch (64 != 32), using 64 bytes [ 1.496823] pci 0000:06:03.0: Video device with shadowed ROM [ 1.496853] Unpacking initramfs... [ 1.690454] Freeing initrd memory: 15968K (ffff8800360c0000 - ffff880037058000) [ 1.697700] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 1.704118] software IO TLB [mem 0xca492000-0xce492000] (64MB) mapped at [ffff8800ca492000-ffff8800ce491fff] [ 1.714164] RAPL PMU detected, hw unit 2^-16 Joules, API unit is 2^-32 Joules, 3 fixed counters 163840 ms ovfl timer [ 1.724674] microcode: CPU0 sig=0x306a9, pf=0x2, revision=0x1b [ 1.730426] microcode: CPU1 sig=0x306a9, pf=0x2, revision=0x1b [ 1.736250] microcode: CPU2 sig=0x306a9, pf=0x2, revision=0x1b [ 1.750730] microcode: CPU3 sig=0x306a9, pf=0x2, revision=0x1b [ 1.756546] microcode: CPU4 sig=0x306a9, pf=0x2, revision=0x1b [ 1.762360] microcode: CPU5 sig=0x306a9, pf=0x2, revision=0x1b [ 1.768179] microcode: CPU6 sig=0x306a9, pf=0x2, revision=0x1b [ 1.773991] microcode: CPU7 sig=0x306a9, pf=0x2, revision=0x1b [ 1.779835] microcode: Microcode Update Driver: v2.00 <tig...@aivazian.fsnet.co.uk>, Peter Oruba [ 1.788826] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 1.795033] audit: initializing netlink subsys (disabled) [ 1.800388] audit: type=2000 audit(1443100076.548:1): initialized [ 1.806664] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 1.812933] zpool: loaded [ 1.815517] zbud: loaded [ 1.818158] VFS: Disk quotas dquot_6.5.2 [ 1.821997] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 1.828445] msgmni has been set to 32768 [ 1.832595] alg: No test for stdrng (krng) [ 1.836625] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.844014] io scheduler noop registered [ 1.847878] io scheduler deadline registered [ 1.852131] io scheduler cfq registered (default) [ 1.856959] pcieport 0000:00:01.0: irq 24 for MSI/MSI-X [ 1.857070] pcieport 0000:00:01.1: irq 25 for MSI/MSI-X [ 1.857283] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 1.862775] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 1.869391] intel_idle: MWAIT substates: 0x1120 [ 1.869392] intel_idle: v0.4 model 0x3A [ 1.869393] intel_idle: lapic_timer_reliable_states 0xffffffff [ 1.869628] ERST: Error Record Serialization Table (ERST) support is initialized. [ 1.877034] pstore: Registered erst as persistent store backend [ 1.882975] GHES: APEI firmware first mode is enabled by WHEA _OSC. [ 1.889229] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.915898] 00:06: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 1.943574] 00:07: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 1.971232] 00:09: ttyS2 at I/O 0x3e8 (irq = 10, base_baud = 115200) is a 16550A [ 1.978753] Linux agpgart interface v0.103 [ 1.982831] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 1.992701] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.997575] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.002720] mousedev: PS/2 mouse device common for all mice [ 2.008232] rtc_cmos 00:02: RTC can wake from S4 [ 2.012908] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0 [ 2.018943] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 2.026564] ledtrig-cpu: registered to indicate activity on CPUs [ 2.032717] AMD IOMMUv2 driver by Joerg Roedel <joerg.roe...@amd.com> [ 2.039059] AMD IOMMUv2 functionality not available on this system [ 2.045283] TCP: cubic registered [ 2.048521] IPv6: Loaded, but administratively disabled, reboot required to enable [ 2.056071] mip6: Mobile IPv6 [ 2.059020] mip6: mip6_init: can't add xfrm type(destopt) [ 2.064404] NET: Registered protocol family 17 [ 2.068836] mpls_gso: MPLS GSO support [ 2.072972] registered taskstats version 1 [ 2.077499] rtc_cmos 00:02: setting system clock to 2015-09-24 13:07:57 UTC (1443100077) [ 2.085560] PM: Hibernation image not present or could not be loaded. [ 2.086094] Freeing unused kernel memory: 1228K (ffffffff818f3000 - ffffffff81a26000) [ 2.093851] Write protecting the kernel read-only data: 8192k [ 2.100532] Freeing unused kernel memory: 620K (ffff880001565000 - ffff880001600000) [ 2.108556] Freeing unused kernel memory: 216K (ffff8800017ca000 - ffff880001800000) [ 2.123393] udevd[94]: starting version 175 [ 2.131920] pps_core: LinuxPPS API ver. 1 registered [ 2.136823] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giome...@linux.it> [ 2.147106] PTP clock support registered [ 2.151071] ACPI: bus type USB registered [ 2.155038] usbcore: registered new interface driver usbfs [ 2.160469] usbcore: registered new interface driver hub [ 2.165787] usbcore: registered new device driver usb [ 2.171019] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k [ 2.176789] e1000e: Copyright(c) 1999 - 2014 Intel Corporation. [ 2.182928] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.189595] ehci-pci: EHCI PCI platform driver [ 2.194192] i40e: Intel(R) Ethernet Connection XL710 Network Driver - version 1.3.39.1 [ 2.197599] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.197641] e1000e 0000:00:19.0: irq 26 for MSI/MSI-X [ 2.198073] thermal LNXTHERM:00: registered as thermal_zone0 [ 2.198073] ACPI: Thermal Zone [TZ00] (28 C) [ 2.198216] thermal LNXTHERM:01: registered as thermal_zone1 [ 2.198216] ACPI: Thermal Zone [TZ01] (30 C) [ 2.231104] i40e: Copyright (c) 2013 - 2015 Intel Corporation. [ 2.249391] i40e 0000:02:00.0: fw 4.40.35115 api 1.4 nvm 4.53 0x80001dc0 1.123.0 [ 2.256998] SCSI subsystem initialized [ 2.261957] libata version 3.00 loaded. [ 2.453377] e1000e 0000:00:19.0 eth0: registered PHC clock [ 2.458796] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:a8:02:51 [ 2.466693] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection [ 2.473600] e1000e 0000:00:19.0 eth0: MAC: 10, PHY: 11, PBA No: FFFFFF-0FF [ 2.480564] ehci-pci 0000:00:1a.0: EHCI Host Controller [ 2.480631] e1000e 0000:05:00.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 2.480663] e1000e 0000:05:00.0: irq 27 for MSI/MSI-X [ 2.480665] e1000e 0000:05:00.0: irq 28 for MSI/MSI-X [ 2.480667] e1000e 0000:05:00.0: irq 29 for MSI/MSI-X [ 2.495076] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1 [ 2.495874] i40e 0000:02:00.0: MAC address: 3c:fd:fe:9c:56:b8 [ 2.499857] i40e 0000:02:00.0: SAN MAC: 3c:fd:fe:9c:56:ba [ 2.513542] ehci-pci 0000:00:1a.0: debug port 2 [ 2.514095] i40e 0000:02:00.0: irq 30 for MSI/MSI-X [ 2.514098] i40e 0000:02:00.0: irq 31 for MSI/MSI-X [ 2.514099] i40e 0000:02:00.0: irq 32 for MSI/MSI-X [ 2.514101] i40e 0000:02:00.0: irq 33 for MSI/MSI-X [ 2.514103] i40e 0000:02:00.0: irq 34 for MSI/MSI-X [ 2.514105] i40e 0000:02:00.0: irq 35 for MSI/MSI-X [ 2.514107] i40e 0000:02:00.0: irq 36 for MSI/MSI-X [ 2.514108] i40e 0000:02:00.0: irq 37 for MSI/MSI-X [ 2.514110] i40e 0000:02:00.0: irq 38 for MSI/MSI-X [ 2.514111] i40e 0000:02:00.0: irq 39 for MSI/MSI-X [ 2.514113] i40e 0000:02:00.0: irq 40 for MSI/MSI-X [ 2.514114] i40e 0000:02:00.0: irq 41 for MSI/MSI-X [ 2.514116] i40e 0000:02:00.0: irq 42 for MSI/MSI-X [ 2.514118] i40e 0000:02:00.0: irq 43 for MSI/MSI-X [ 2.514119] i40e 0000:02:00.0: irq 44 for MSI/MSI-X [ 2.514121] i40e 0000:02:00.0: irq 45 for MSI/MSI-X [ 2.514122] i40e 0000:02:00.0: irq 46 for MSI/MSI-X [ 2.514124] i40e 0000:02:00.0: irq 47 for MSI/MSI-X [ 2.521951] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported [ 2.521964] ehci-pci 0000:00:1a.0: irq 16, io mem 0xdfb24000 [ 2.537912] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00 [ 2.543607] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.550333] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.557541] usb usb1: Product: EHCI Host Controller [ 2.562399] usb usb1: Manufacturer: Linux 3.18.20 ehci_hcd [ 2.568471] usb usb1: SerialNumber: 0000:00:1a.0 [ 2.573164] hub 1-0:1.0: USB hub found [ 2.576818] hub 1-0:1.0: 2 ports detected [ 2.580962] ehci-pci 0000:00:1d.0: EHCI Host Controller [ 2.586095] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.593480] ehci-pci 0000:00:1d.0: debug port 2 [ 2.599535] e1000e 0000:05:00.0 eth2: registered PHC clock [ 2.601911] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported [ 2.601922] ehci-pci 0000:00:1d.0: irq 23, io mem 0xdfb23000 [ 2.610602] e1000e 0000:05:00.0 eth2: (PCI Express:2.5GT/s:Width x1) 00:25:90:a8:02:50 [ 2.613936] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00 [ 2.613963] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.613964] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.613965] usb usb2: Product: EHCI Host Controller [ 2.613965] usb usb2: Manufacturer: Linux 3.18.20 ehci_hcd [ 2.613966] usb usb2: SerialNumber: 0000:00:1d.0 [ 2.614075] hub 2-0:1.0: USB hub found [ 2.614078] hub 2-0:1.0: 2 ports detected [ 2.614192] ahci 0000:00:1f.2: version 3.0 [ 2.614340] ahci 0000:00:1f.2: irq 48 for MSI/MSI-X [ 2.614485] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 3 Gbps 0x3f impl SATA mode [ 2.614486] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems apst [ 2.626630] i40e 0000:02:00.0: PCI-Express: Speed 8.0GT/s Width x8 [ 2.654604] scsi host0: ahci [ 2.654992] i40e 0000:02:00.0: Features: PF-id[0] VFs: 64 VSIs: 66 QP: 8 RX: 1BUF RSS FD_ATR FD_SB NTUPLE DCB VxLAN PTP VEPA [ 2.657763] scsi host1: ahci [ 2.658083] scsi host2: ahci [ 2.658320] scsi host3: ahci [ 2.658546] scsi host4: ahci [ 2.658747] scsi host5: ahci [ 2.658785] ata1: SATA max UDMA/133 abar m2048@0xdfb22000 port 0xdfb22100 irq 48 [ 2.658788] ata2: SATA max UDMA/133 abar m2048@0xdfb22000 port 0xdfb22180 irq 48 [ 2.658790] ata3: SATA max UDMA/133 abar m2048@0xdfb22000 port 0xdfb22200 irq 48 [ 2.658792] ata4: SATA max UDMA/133 abar m2048@0xdfb22000 port 0xdfb22280 irq 48 [ 2.658795] ata5: SATA max UDMA/133 abar m2048@0xdfb22000 port 0xdfb22300 irq 48 [ 2.658798] ata6: SATA max UDMA/133 abar m2048@0xdfb22000 port 0xdfb22380 irq 48 [ 2.670025] i40e 0000:02:00.1: fw 4.40.35115 api 1.4 nvm 4.53 0x80001dc0 1.123.0 [ 2.714122] tsc: Refined TSC clocksource calibration: 3500.024 MHz [ 2.769612] e1000e 0000:05:00.0 eth2: Intel(R) PRO/1000 Network Connection [ 2.776551] e1000e 0000:05:00.0 eth2: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF [ 2.890322] usb 1-1: new high-speed USB device number 2 using ehci-pci [ 2.916415] i40e 0000:02:00.1: MAC address: 3c:fd:fe:9c:56:b9 [ 2.926260] i40e 0000:02:00.1: SAN MAC: 3c:fd:fe:9c:56:bb [ 2.930381] usb 2-1: new high-speed USB device number 2 using ehci-pci [ 2.952496] i40e 0000:02:00.1: irq 49 for MSI/MSI-X [ 2.952503] i40e 0000:02:00.1: irq 50 for MSI/MSI-X [ 2.952508] i40e 0000:02:00.1: irq 51 for MSI/MSI-X [ 2.952512] i40e 0000:02:00.1: irq 52 for MSI/MSI-X [ 2.952516] i40e 0000:02:00.1: irq 53 for MSI/MSI-X [ 2.952520] i40e 0000:02:00.1: irq 54 for MSI/MSI-X [ 2.952525] i40e 0000:02:00.1: irq 55 for MSI/MSI-X [ 2.952537] i40e 0000:02:00.1: irq 56 for MSI/MSI-X [ 2.952539] i40e 0000:02:00.1: irq 57 for MSI/MSI-X [ 2.952541] i40e 0000:02:00.1: irq 58 for MSI/MSI-X [ 2.952543] i40e 0000:02:00.1: irq 59 for MSI/MSI-X [ 2.952545] i40e 0000:02:00.1: irq 60 for MSI/MSI-X [ 2.952547] i40e 0000:02:00.1: irq 61 for MSI/MSI-X [ 2.952549] i40e 0000:02:00.1: irq 62 for MSI/MSI-X [ 2.952550] i40e 0000:02:00.1: irq 63 for MSI/MSI-X [ 2.952554] i40e 0000:02:00.1: irq 64 for MSI/MSI-X [ 2.952556] i40e 0000:02:00.1: irq 65 for MSI/MSI-X [ 2.952558] i40e 0000:02:00.1: irq 66 for MSI/MSI-X [ 2.978497] ata5: SATA link down (SStatus 0 SControl 300) [ 2.983838] ata6: SATA link down (SStatus 0 SControl 300) [ 2.989225] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.995381] ata4: SATA link down (SStatus 0 SControl 300) [ 3.000756] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 3.007184] ata2: SATA link down (SStatus 0 SControl 300) [ 3.012510] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded [ 3.012514] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out [ 3.020391] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out [ 3.026954] usb 1-1: New USB device found, idVendor=8087, idProduct=0024 [ 3.026955] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.027240] hub 1-1:1.0: USB hub found [ 3.027332] hub 1-1:1.0: 6 ports detected [ 3.050510] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded [ 3.050512] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out [ 3.061847] i40e 0000:02:00.1: PCI-Express: Speed 8.0GT/s Width x8 [ 3.067012] usb 2-1: New USB device found, idVendor=8087, idProduct=0024 [ 3.067013] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 3.067296] hub 2-1:1.0: USB hub found [ 3.067384] hub 2-1:1.0: 6 ports detected [ 3.090237] i40e 0000:02:00.1: Features: PF-id[1] VFs: 64 VSIs: 66 QP: 8 RX: 1BUF RSS FD_ATR FD_SB NTUPLE DCB VxLAN PTP VEPA [ 3.103551] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out [ 3.112266] ata1.00: ATA-8: INTEL SSDSC2BA200G3, 5DV10250, max UDMA/133 [ 3.118799] ata1.00: 390721968 sectors, multi 1: LBA48 NCQ (depth 31/32) [ 3.125486] ata3.00: ATAPI: HL-DT-ST DVDRAM GT80N, 1.00, max UDMA/133 [ 3.132254] ata1.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded [ 3.132259] ata1.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out [ 3.140106] ata1.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out [ 3.148916] ata1.00: configured for UDMA/133 [ 3.153298] scsi 0:0:0:0: Direct-Access ATA INTEL SSDSC2BA20 0250 PQ: 0 ANSI: 5 [ 3.154140] ata3.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded [ 3.154142] ata3.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out [ 3.154143] ata3.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out [ 3.156130] ata3.00: configured for UDMA/133 [ 3.185352] scsi 2:0:0:0: CD-ROM HL-DT-ST DVDRAM GT80N 1.00 PQ: 0 ANSI: 5 [ 3.298953] usb 1-1.2: new full-speed USB device number 3 using ehci-pci [ 3.323219] sd 0:0:0:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB) [ 3.330670] sd 0:0:0:0: [sda] Write Protect is off [ 3.335418] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 3.335427] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 3.338917] sr 2:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 3.338918] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 3.339081] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 3.358408] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 3.358668] sda: sda1 sda2 [ 3.358886] sd 0:0:0:0: [sda] Attached SCSI disk [ 3.371134] sr 2:0:0:0: Attached scsi generic sg1 type 5 [ 3.396737] usb 1-1.2: New USB device found, idVendor=0557, idProduct=2221 [ 3.403526] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.410814] usb 1-1.2: Product: Hermon USB hidmouse Device [ 3.416282] usb 1-1.2: Manufacturer: Winbond Electronics Corp [ 3.423736] hidraw: raw HID events driver (C) Jiri Kosina [ 3.430436] usbcore: registered new interface driver usbhid [ 3.435922] usbhid: USB HID core driver [ 3.440716] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.0/0003:0557:2221.0001/input/input2 [ 3.455434] hid-generic 0003:0557:2221.0001: input,hidraw0: USB HID v1.00 Mouse [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input0 [ 3.470147] input: Winbond Electronics Corp Hermon USB hidmouse Device as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2:1.1/0003:0557:2221.0002/input/input3 [ 3.484849] hid-generic 0003:0557:2221.0002: input,hidraw1: USB HID v1.00 Keyboard [Winbond Electronics Corp Hermon USB hidmouse Device] on usb-0000:00:1a.0-1.2/input1 [ 3.507384] PM: Starting manual resume from disk [ 3.511922] PM: Hibernation image partition 8:1 present [ 3.511923] PM: Looking for hibernation image. [ 3.512127] PM: Image not found (code -22) [ 3.512131] PM: Hibernation image not present or could not be loaded. [ 3.517313] EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem [ 3.529000] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 3.715841] Switched to clocksource tsc [ 3.885031] udevd[667]: starting version 175 [ 4.011695] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input4 [ 4.020070] ACPI: Power Button [PWRB] [ 4.023703] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5 [ 4.031033] ACPI: Power Button [PWRF] [ 4.034781] EDAC MC: Ver: 3.0.0 [ 4.038626] EDAC MC0: Giving out device to module ie31200_edac controller IE31200: DEV 0000:00:00.0 (POLLED) [ 4.115904] ipmi message handler version 39.2 [ 4.121319] IPMI System Interface driver. [ 4.126068] ipmi_si: probing via ACPI [ 4.129851] ipmi_si 00:0a: [io 0x0ca2] regsize 1 spacing 1 irq 0 [ 4.135777] i40e 0000:02:00.1 rename5: renamed from eth3 [ 4.141149] ipmi_si: Adding ACPI-specified kcs state machine [ 4.147092] ipmi_si: probing via SMBIOS [ 4.147160] input: PC Speaker as /devices/platform/pcspkr/input/input6 [ 4.157409] ipmi_si: SMBIOS: io 0xca2 regsize 1 spacing 1 irq 0 [ 4.163305] ipmi_si: Adding SMBIOS-specified kcs state machine duplicate interface [ 4.170854] ipmi_si: probing via SPMI [ 4.174504] ipmi_si: SPMI: io 0xca2 regsize 1 spacing 1 irq 0 [ 4.177849] i40e 0000:02:00.0 rename3: renamed from eth1 [ 4.185527] ipmi_si: Adding SPMI-specified kcs state machine [ 4.185655] ACPI Warning: SystemIO range 0x0000000000000428-0x000000000000042F conflicts with OpRegion 0x0000000000000400-0x000000000000047F (\PMIO) (20140926/utaddress-254) [ 4.185658] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 4.185660] ACPI Warning: SystemIO range 0x0000000000000540-0x000000000000054F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20140926/utaddress-254) [ 4.185662] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 4.185662] ACPI Warning: SystemIO range 0x0000000000000530-0x000000000000053F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20140926/utaddress-254) [ 4.185664] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 4.185664] ACPI Warning: SystemIO range 0x0000000000000500-0x000000000000052F conflicts with OpRegion 0x0000000000000500-0x0000000000000563 (\GPIO) (20140926/utaddress-254) [ 4.185665] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver [ 4.185665] lpc_ich: Resource conflict(s) found affecting gpio_ich [ 4.280990] iTCO_vendor_support: vendor-support=0 [ 4.304270] duplicate interface [ 4.307664] ipmi_si: Trying ACPI-specified kcs state machine at i/o address 0xca2, slave address 0x0, irq 0 [ 4.318187] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11 [ 4.323711] iTCO_wdt: Found a Cougar Point TCO device (Version=2, TCOBASE=0x0460) [ 4.323818] e1000e 0000:00:19.0 eth3: renamed from eth0 [ 4.336446] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 4.342474] AVX version of gcm_enc/dec engaged. [ 4.346907] AES CTR mode by8 optimization enabled [ 4.351931] i801_smbus 0000:00:1f.3: SMBus using PCI Interrupt [ 4.352819] alg: No test for __gcm-aes-aesni (__driver-gcm-aes-aesni) [ 4.364158] i40e 0000:02:00.1 eth1: renamed from rename5 [ 4.370154] [drm] Initialized drm 1.1.0 20060810 [ 4.374797] Error: Driver 'pcspkr' is already registered, aborting... [ 4.381228] alg: No test for crc32 (crc32-pclmul) [ 4.395990] [TTM] Zone kernel: Available graphics memory: 16494382 kiB [ 4.396626] i40e 0000:02:00.0 eth0: renamed from rename3 [ 4.407813] [TTM] Zone dma32: Available graphics memory: 2097152 kiB [ 4.414324] [TTM] Initializing pool allocator [ 4.418678] [TTM] Initializing DMA pool allocator [ 4.425605] intel_rapl: Found RAPL domain package [ 4.430215] intel_rapl: Found RAPL domain core [ 4.446166] fbcon: mgadrmfb (fb0) is primary device [ 4.489833] ipmi_si 00:0a: Found new BMC (man_id: 0x002a7c, prod_id: 0x0624, dev_id: 0x20) [ 4.489843] ipmi_si 00:0a: IPMI kcs interface initialized [ 4.604074] Console: switching to colour frame buffer device 128x48 [ 4.698245] mgag200 0000:06:03.0: fb0: mgadrmfb frame buffer device [ 4.704491] mgag200 0000:06:03.0: registered panic notifier [ 4.733133] [drm] Initialized mgag200 1.0.0 20110418 for 0000:06:03.0 on minor 0 [ 4.975874] Adding 3905532k swap on /dev/sda1. Priority:-1 extents:1 across:3905532k SSFS [ 5.002394] EXT4-fs (sda2): re-mounted. Opts: (null) [ 5.044749] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro [ 5.077354] loop: module loaded [ 5.087636] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 5.101990] nf_conntrack version 0.5.0 (17374463 buckets, 138995704 max) [ 5.108653] nf_conntrack: falling back to vmalloc. [ 5.735510] random: dd urandom read with 92 bits of entropy available [ 5.927034] bond0: Setting xmit hash policy to layer3+4 (1) [ 5.927105] bond0: Setting MII monitoring interval to 100 [ 5.963685] bond0: Setting LACP rate to slow (0) [ 6.119830] bond0: Adding slave eth0 [ 6.119841] i40e 0000:02:00.0 eth0: already using mac address 3c:fd:fe:9c:56:b8 [ 6.123689] i40e 0000:02:00.0 eth0: NIC Link is Up 10 Gbps Full Duplex, Flow Control: None [ 6.123746] bond0: Enslaving eth0 as a backup interface with an up link [ 6.126208] bond0: Adding slave eth1 [ 6.126212] i40e 0000:02:00.1 eth1: set new mac address 3c:fd:fe:9c:56:b8 [ 6.135693] i40e 0000:02:00.1 eth1: NIC Link is Up 10 Gbps Full Duplex, Flow Control: None [ 6.135756] bond0: Enslaving eth1 as a backup interface with an up link [ 7.145905] random: nonblocking pool is initialized [ 12.460991] Process accounting resumed [ 12.918920] e1000e 0000:00:19.0: irq 26 for MSI/MSI-X [ 13.021814] e1000e 0000:00:19.0: irq 26 for MSI/MSI-X [ 13.279044] nf_conntrack: falling back to vmalloc. [ 13.323161] ip_tables: (C) 2000-2006 Netfilter Core Team On 2015-08-27 16:43, Rose, Gregory V wrote: >> -----Original Message----- >> From: Christian Ruppert [mailto:id...@qasl.de] >> Sent: Thursday, August 27, 2015 4:54 AM >> To: Fujinaka, Todd >> Cc: Rose, Gregory V; e1000-de...@lists.sf.net >> Subject: RE: [E1000-devel] X710 / i40e interface resets >> >> Well, that's it for now anyway... >> >> ... >> Power cycle is required to complete the update process. >> Tool execution completed with the following status: All operations >> completed successfully >> >> The card doesn't even appear in "lspci" anymore... :/ I used a Win7 to >> flash it since a co-worker already broke one when flashing via Linux. >> No >> idea how to unbrick it. > > Christian, > > I'm very sorry to hear that. It is pretty rare for this sort of thing > to happen but not unheard of. Please contact supp...@intel.com to get > help replacing the part. > > - Greg > >> >> >> On 2015-08-27 01:25, Fujinaka, Todd wrote: >> > Attachments don't work on this mailing list (though they may have >> > gotten to Greg). Please file a bug on e1000.sourceforge.net and attach >> > the files there. >> > >> > Todd Fujinaka >> > Software Application Engineer >> > Networking Division (ND) >> > Intel Corporation >> > todd.fujin...@intel.com >> > (503) 712-4565 >> > >> > -----Original Message----- >> > From: Christian Ruppert [mailto:id...@qasl.de] >> > Sent: Wednesday, August 26, 2015 10:24 AM >> > To: Rose, Gregory V >> > Cc: e1000-de...@lists.sf.net >> > Subject: Re: [E1000-devel] X710 / i40e interface resets >> > >> > On 2015-08-26 01:19, Rose, Gregory V wrote: >> >>> -----Original Message----- >> >>> From: Christian Ruppert [mailto:id...@qasl.de] >> >>> Sent: Friday, August 21, 2015 7:06 AM >> >>> To: Rose, Gregory V >> >>> Cc: e1000-de...@lists.sf.net >> >>> Subject: RE: [E1000-devel] X710 / i40e interface resets >> >>> >> >>> On 2015-07-28 18:51, Rose, Gregory V wrote: >> >>> >> -----Original Message----- >> >>> >> From: Christian Ruppert [mailto:id...@qasl.de] >> >>> >> Sent: Tuesday, July 28, 2015 5:43 AM >> >>> >> To: Rose, Gregory V >> >>> >> Cc: e1000-de...@lists.sf.net >> >>> >> Subject: RE: [E1000-devel] X710 / i40e interface resets >> >>> >> >> >> >> >> [snip] >> >> >> >>> > I've been told that the Tx driver issue detected message is due to >> >>> > a MDD (Malicious Driver Detection) event. We need to find out what >> >>> > is causing that so if you could please send me your system log and >> >>> > the output of ethtool <intf> and ethtool -i <intf> perhaps I can >> >>> > see what might be occurring. If not then we'll have to debug >> further. >> >>> >> >>> See the initial Mail for ethtool -k and so on. Also: >> >>> # ethtool eth0 >> >>> Settings for eth0: >> >>> Supported ports: [ FIBRE ] >> >>> Supported link modes: 1000baseT/Full >> >>> 10000baseT/Full >> >>> Supported pause frame use: Symmetric >> >>> Supports auto-negotiation: No >> >>> Advertised link modes: 1000baseT/Full >> >>> 10000baseT/Full >> >>> Advertised pause frame use: No >> >>> Advertised auto-negotiation: No >> >>> Speed: 10000Mb/s >> >>> Duplex: Full >> >>> Port: FIBRE >> >>> PHYAD: 0 >> >>> Transceiver: external >> >>> Auto-negotiation: off >> >>> Supports Wake-on: d >> >>> Wake-on: d >> >>> Current message level: 0x0000000f (15) >> >>> drv probe link timer >> >>> Link detected: yes >> >>> # ethtool -i eth0 >> >>> driver: i40e >> >>> version: 1.2.48 >> >>> firmware-version: f4.33.31377 a1.2 n4.42 e191b >> >>> bus-info: 0000:02:00.0 >> >>> supports-statistics: yes >> >>> supports-test: yes >> >>> supports-eeprom-access: yes >> >>> supports-register-dump: yes >> >>> supports-priv-flags: yes >> >> >> >> I also need the output of 'dmesg' - and I need to figure out how to >> >> determine what specific MDD event is occurring. I'll get back to you >> >> with instructions on how to do that when I get the system log from >> >> you. >> > >> > See the attached file. It's a dmesg from boot + some minutes. >> > I'll upgrade the card's firmware tomorrow I guess and try out the new >> > drivers btw. >> > >> >> >> >> Thanks, >> >> >> >> - Greg >> > >> > -- >> > Regards, >> > Christian Ruppert >> >> -- >> Regards, >> Christian Ruppert -- Regards, Christian Ruppert ------------------------------------------------------------------------------ _______________________________________________ E1000-devel mailing list E1000-devel@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/e1000-devel To learn more about Intel® Ethernet, visit http://communities.intel.com/community/wired
