Hey Peter,

Sorry our hardware doesn't support LX4 modules, which is what I'm assuming you 
mean by WDM SFP+.   The unsupported module parameter is only used for modules 
that we recognize but haven't validated.  This way we at least know the module 
won't hurt the hardware even if we can't vouch for their performance.   
Attempting to use any unknown SFP+ module that was plugged in (assuming zero 
init) could potently harm the HW.

Thanks,
-Don <donald.c.skidm...@intel.com>

> -----Original Message-----
> From: Peter Volkov [mailto:peter.vol...@gmail.com]
> Sent: Tuesday, January 05, 2016 8:54 PM
> To: e1000-devel@lists.sourceforge.net
> Subject: [E1000-devel] ixgbe: link flapping on two directly connected servers
> with 82599ES adapter
> 
> Good time.
> 
> We experince link flapping while connecting two supermicro servers with
> 82599ES adapters:
> 
> [Wed Jan  6 07:10:14 2016] ixgbe 0000:81:00.1 enp129s0f1: NIC Link is Down
> [Wed Jan  6 07:10:15 2016] ixgbe 0000:81:00.1 enp129s0f1: NIC Link is Up 10
> Gbps, Flow Control: RX/TX [Wed Jan  6 07:10:15 2016] ixgbe 0000:81:00.1
> enp129s0f1: NIC Link is Down [Wed Jan  6 07:10:16 2016] ixgbe 0000:81:00.1
> enp129s0f1: NIC Link is Up 10 Gbps, Flow Control: RX/TX [Wed Jan  6
> 07:10:16 2016] ixgbe 0000:81:00.1 enp129s0f1: NIC Link is Down [Wed Jan  6
> 07:10:16 2016] ixgbe 0000:81:00.1 enp129s0f1: NIC Link is Up 10 Gbps, Flow
> Control: RX/TX [Wed Jan  6 07:10:16 2016] ixgbe 0000:81:00.1 enp129s0f1:
> NIC Link is Down [Wed Jan  6 07:10:16 2016] ixgbe 0000:81:00.1 enp129s0f1:
> NIC Link is Up 10 Gbps, Flow Control: RX/TX [Wed Jan  6 07:10:17 2016]
> ixgbe 0000:81:00.1 enp129s0f1: NIC Link is Down [Wed Jan  6 07:10:17 2016]
> ixgbe 0000:81:00.1 enp129s0f1: NIC Link is Up 10 Gbps, Flow Control: RX/TX
> 
> So we are trying to connect two supermicro servers with E10G42BTDA
> X520-DA2 controller
> in each server:
> 81:00.0 Ethernet controller: Intel Corporation 82599ES 10-Gigabit SFI/SFP+
> Network Connection (rev 01)
> 
> In one controller there is following SFP module:
> 
> # ethtool --module-info enp129s0f1
> Identifier                                : 0x03 (SFP)
> Extended identifier                       : 0x04 (GBIC/SFP defined by
> 2-wire interface ID)
> Connector                                 : 0x07 (LC)
> Transceiver codes                         : 0x20 0x00 0x00 0x00 0x00 0x00
> 0x00 0x00
> Transceiver type                          : 10G Ethernet: 10G Base-LR
> Encoding                                  : 0x06 (64B/66B)
> BR, Nominal                               : 10300MBd
> Rate identifier                           : 0x00 (unspecified)
> Length (SMF,km)                           : 20km
> Length (SMF)                              : 20000m
> Length (50um)                             : 0m
> Length (62.5um)                           : 0m
> Length (Copper)                           : 0m
> Length (OM3)                              : 0m
> Laser wavelength                          : 1330nm
> Vendor name                               : GIGALINK
> Vendor OUI                                : 00:90:65
> Vendor PN                                 : GL-OT-ST12LC1-13
> Vendor rev                                : A
> Optical diagnostics support               : Yes
> Laser bias current                        : 37.020 mA
> Laser output power                        : 0.9654 mW / -0.15 dBm
> Receiver signal average optical power     : 0.4904 mW / -3.09 dBm
> Module temperature                        : 44.23 degrees C / 111.61
> degrees F
> Module voltage                            : 3.2836 V
> Alarm/warning flags implemented           : Yes
> Laser bias current high alarm             : Off
> Laser bias current low alarm              : Off
> Laser bias current high warning           : Off
> Laser bias current low warning            : Off
> Laser output power high alarm             : Off
> Laser output power low alarm              : Off
> Laser output power high warning           : Off
> Laser output power low warning            : Off
> Module temperature high alarm             : Off
> Module temperature low alarm              : Off
> Module temperature high warning           : Off
> Module temperature low warning            : Off
> Module voltage high alarm                 : Off
> Module voltage low alarm                  : Off
> Module voltage high warning               : Off
> Module voltage low warning                : Off
> Laser rx power high alarm                 : Off
> Laser rx power low alarm                  : Off
> Laser rx power high warning               : Off
> Laser rx power low warning                : Off
> Laser bias current high alarm threshold   : 85.000 mA
> Laser bias current low alarm threshold    : 10.000 mA
> Laser bias current high warning threshold : 80.000 mA Laser bias current low
> warning threshold  : 12.000 mA
> Laser output power high alarm threshold   : 3.1623 mW / 5.00 dBm
> Laser output power low alarm threshold    : 0.3162 mW / -5.00 dBm
> Laser output power high warning threshold : 2.5119 mW / 4.00 dBm Laser
> output power low warning threshold  : 0.3981 mW / -4.00 dBm
> Module temperature high alarm threshold   : 85.00 degrees C / 185.00
> degrees F
> Module temperature low alarm threshold    : -10.00 degrees C / 14.00
> degrees F
> Module temperature high warning threshold : 80.00 degrees C / 176.00
> degrees F Module temperature low warning threshold  : -5.00 degrees C /
> 23.00 degrees F
> Module voltage high alarm threshold       : 3.7000 V
> Module voltage low alarm threshold        : 2.9000 V
> Module voltage high warning threshold     : 3.6000 V
> Module voltage low warning threshold      : 3.0000 V
> Laser rx power high alarm threshold       : 1.0000 mW / 0.00 dBm
> Laser rx power low alarm threshold        : 0.0200 mW / -16.99 dBm
> Laser rx power high warning threshold     : 0.7943 mW / -1.00 dBm
> Laser rx power low warning threshold      : 0.0251 mW / -16.00 dBm
> 
> In another controller:
> 
> # ethtool --module-info enp129s0f1
> Identifier                                : 0x03 (SFP)
> Extended identifier                       : 0x04 (GBIC/SFP defined by
> 2-wire interface ID)
> Connector                                 : 0x07 (LC)
> Transceiver codes                         : 0x20 0x00 0x00 0x00 0x00 0x00
> 0x00 0x00
> Transceiver type                          : 10G Ethernet: 10G Base-LR
> Encoding                                  : 0x06 (64B/66B)
> BR, Nominal                               : 10300MBd
> Rate identifier                           : 0x00 (unspecified)
> Length (SMF,km)                           : 20km
> Length (SMF)                              : 20000m
> Length (50um)                             : 0m
> Length (62.5um)                           : 0m
> Length (Copper)                           : 0m
> Length (OM3)                              : 0m
> Laser wavelength                          : 1270nm
> Vendor name                               : GIGALINK
> Vendor OUI                                : 00:90:65
> Vendor PN                                 : GL-OT-ST12LC1-12
> Vendor rev                                : A
> Option values                             : 0x00 0x1a
> Option                                    : RX_LOS implemented
> Option                                    : TX_FAULT implemented
> Option                                    : TX_DISABLE implemented
> BR margin, max                            : 0%
> BR margin, min                            : 0%
> Vendor SN                                 : G201511300616
> Date code                                 : 151118
> Optical diagnostics support               : Yes
> Laser bias current                        : 35.120 mA
> Laser output power                        : 0.7842 mW / -1.06 dBm
> Receiver signal average optical power     : 0.5695 mW / -2.45 dBm
> Module temperature                        : 45.68 degrees C / 114.22
> degrees F
> Module voltage                            : 3.2440 V
> Alarm/warning flags implemented           : Yes
> Laser bias current high alarm             : Off
> Laser bias current low alarm              : Off
> Laser bias current high warning           : Off
> Laser bias current low warning            : Off
> Laser output power high alarm             : Off
> Laser output power low alarm              : Off
> Laser output power high warning           : Off
> Laser output power low warning            : Off
> Module temperature high alarm             : Off
> Module temperature low alarm              : Off
> Module temperature high warning           : Off
> Module temperature low warning            : Off
> Module voltage high alarm                 : Off
> Module voltage low alarm                  : Off
> Module voltage high warning               : Off
> Module voltage low warning                : Off
> Laser rx power high alarm                 : Off
> Laser rx power low alarm                  : Off
> Laser rx power high warning               : Off
> Laser rx power low warning                : Off
> Laser bias current high alarm threshold   : 85.000 mA
> Laser bias current low alarm threshold    : 10.000 mA
> Laser bias current high warning threshold : 80.000 mA Laser bias current low
> warning threshold  : 12.000 mA
> Laser output power high alarm threshold   : 3.1623 mW / 5.00 dBm
> Laser output power low alarm threshold    : 0.3162 mW / -5.00 dBm
> Laser output power high warning threshold : 2.5119 mW / 4.00 dBm Laser
> output power low warning threshold  : 0.3981 mW / -4.00 dBm
> Module temperature high alarm threshold   : 85.00 degrees C / 185.00
> degrees F
> Module temperature low alarm threshold    : -10.00 degrees C / 14.00
> degrees F
> Module temperature high warning threshold : 80.00 degrees C / 176.00
> degrees F Module temperature low warning threshold  : -5.00 degrees C /
> 23.00 degrees F
> Module voltage high alarm threshold       : 3.7000 V
> Module voltage low alarm threshold        : 2.9000 V
> Module voltage high warning threshold     : 3.6000 V
> Module voltage low warning threshold      : 3.0000 V
> Laser rx power high alarm threshold       : 1.0000 mW / 0.00 dBm
> Laser rx power low alarm threshold        : 0.0200 mW / -16.99 dBm
> Laser rx power high warning threshold     : 0.7943 mW / -1.00 dBm
> Laser rx power low warning threshold      : 0.0251 mW / -16.00 dBm
> 
> 
> We've checked both SFP+ modules and patchcord in other hardware and link
> was working fine there. As for module version we've tried both 4.1.5 and
> 4.3.13 and we experience problem with both versions. I've built v4.3.13
> module with printk enabled, and I found following messages in dmesg:
> 
> [Wed Jan  6 06:04:02 2016] ixgbe 0000:81:00.1 enp129s0f1: NIC Link is Up 10
> Gbps, Flow Control: RX/TX [Wed Jan  6 06:04:02 2016]
> ixgbe_get_media_type_82599 [Wed Jan  6 06:04:02 2016]
> ixgbe_check_mac_link_generic [Wed Jan  6 06:04:02 2016]
> ixgbe_get_media_type_82599 [Wed Jan  6 06:04:02 2016] ixgbe
> 0000:81:00.1 enp129s0f1: NIC Link is Down [Wed Jan  6 06:04:02 2016]
> ixgbe_check_mac_link_genericixgbe_fc_enable_genericixgbe_fc_autonegixg
> be_check_mac_link_generic
> [Wed Jan  6 06:04:02 2016] ixgbe 0000:81:00.1 enp129s0f1: NIC Link is Up 10
> Gbps, Flow Control: RX/TX [Wed Jan  6 06:04:02 2016]
> ixgbe_get_media_type_82599 [Wed Jan  6 06:04:02 2016]
> ixgbe_check_mac_link_generic [Wed Jan  6 06:04:02 2016]
> ixgbe_get_media_type_82599 [Wed Jan  6 06:04:02 2016] ixgbe
> 0000:81:00.1 enp129s0f1: NIC Link is Down
> 
> Does this helps to understand reasons for such behaviour?
> 
> What makes me wonder. In Documentation/networking/ixgbe.txt I found
> following information
> 
> *82599-BASED ADAPTERS*
> 
> *NOTES: If your 82599-based Intel(R) Network Adapter came with Intel
> optics, or* *is an Intel(R) Ethernet Server Adapter X520-2, then it only
> supports Intel* *optics and/or the direct attach cables listed below.*
> 
> *When 82599-based SFP+ devices are connected back to back, they should
> be set to* *the same Speed setting via ethtool. Results may vary if you mix
> speed
> settings.*
> *82598-based adapters support all passive direct attach cables that comply*
> *with SFF-8431 v4.1 and SFF-8472 v10.4 specifications. Active direct attach*
> *cables are not supported.*
> 
> Yet any attempt to set speed fails:
> # ethtool -s enp129s0f1 speed 10000
> Cannot set new settings: Invalid argument
>   not setting speed
> 
> Why is that? That said I found suggestion to set advertising mode:
> 
> ethtool -s enp129s0f1 advertise 0x1000
> 
> and this worked, but link flapping continues.
> 
> Yes, I realize that these modules are unsupported and to make them working
> I had to load module with allow_unsupported_sfp=1,1 but the main problem
> we have is that I failed to find any intel suggested WDM SFP+ module. We
> need to use only single fiber cable since in our final configuration we need 
> to
> connect both servers to our provider and they highly recomend WDM
> connections. If these modules are not going to work does there exist any
> WDM module that will?
> 
> # ethtool -i enp129s0f1
> driver: ixgbe
> version: 4.1.5
> firmware-version: 0x61c10001
> bus-info: 0000:81:00.1
> supports-statistics: yes
> supports-test: yes
> supports-eeprom-access: yes
> supports-register-dump: yes
> supports-priv-flags: no
> 
>  # ethtool enp129s0f1
> Settings for enp129s0f1:
> Supported ports: [ FIBRE ]
> Supported link modes:   10000baseT/Full
> Supported pause frame use: No
> Supports auto-negotiation: No
> Advertised link modes:  10000baseT/Full
> Advertised pause frame use: Symmetric
> Advertised auto-negotiation: No
> Speed: 10000Mb/s
> Duplex: Full
> Port: FIBRE
> PHYAD: 0
> Transceiver: external
> Auto-negotiation: off
> Supports Wake-on: d
> Wake-on: d
> Current message level: 0x00000007 (7)
>       drv probe link
> Link detected: yes
> 
> We've struggle with this problem for few days already so any suggestions are
> more then wellcome.
> 
> 
> TIA,
> --
> Peter.
------------------------------------------------------------------------------
_______________________________________________
E1000-devel mailing list
E1000-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/e1000-devel
To learn more about Intel&#174; Ethernet, visit 
http://communities.intel.com/community/wired

Reply via email to